40 Pin Female IDE to SATA Adapter Converter
Allows connection of a SATA device to an IDE motherboard or card
Product ID: IDE2SAT25
- Compliant with SATA specification 1.0 and Ultra ATA-133
- Compact form factor
- No driver/software installation required
This IDE to SATA adapter converts a 40-pin IDE connector to a SATA connector, allowing you to connect a 2.5in or 3.5in SATA (SATA, SATA II/SATA 300) drive to the motherboard in place of an IDE drive.
The IDE to SATA Adapter is suitable for installation in any computer case, as it is requires minimal space and does not impact airflow.
The StarTech.com Advantage
- A compact form factor to fit into almost any installation and no driver installation for true plug and play installation
- Backed by a lifetime warranty and free lifetime technical support
Connect newer SATA devices to older IDE motherboards
Replace an old IDE hard drive with a new SATA drive
Small form factor systems with limited room for adapters/converters
|Chipset ID||JMicron - JM20330|
|Maximum Data Transfer Rate||133 MBps|
|Connector Type(s)||1 - IDE (40 Pin, EIDE/PATA) Female|
|1 - SATA (7 pin, Data) Plug|
|1 - SP4 (4 pin, Small Drive Power) Male|
|OS Compatibility||OS independent; No software or drivers required|
|Product Height||0.4 in [9 mm]|
|Product Length||3.1 in [80 mm]|
|Product Weight||0.4 oz [12 g]|
|Product Width||1.3 in [32 mm]|
|Shipping (Package) Weight||0.5 lb [0.2 kg]|
|What's in the Box|
|Included in Package||1 - IDE to SATA Adapter|
|1 - SATA Cable|
|1 - Y Cable (LP4 to LP4 + SP4)|
|1 - Instruction Manual|
Quickly and easily connect SATA and/or IDE hard drives through USB 2.0
Connect 2 SATA hard drives to an IDE motherboard or card
Drivers & Downloads
Frequently Asked Questions
Before You Buy
Note: For more information on how to detect an IDE hard drive, visit http://www.startech.com/faq/hard_drive_accessories_ide_detection.
Older IDE drives are not supported by current StarTech.com products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.
There are a number of reasons that older IDE drives may not be detected, including the following:
The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).
The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).
The sector size is not 512 bytes.
Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.
Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size
If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.
When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.
There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.
* Product appearance and specifications are subject to change without notice.