Product ID: IPUSB2HD3
This HDMI over IP extender lets you share an HDMI display or projector with the wireless or wired computer on your network. With intuitive controls and effortless screen sharing, this extender makes it easier than ever for users to collaborate and deliver presentations in boardrooms and office meetings.
The IP video extender supports resolutions up to 1080p and features two built-in USB ports, enabling you to connect remote USB devices to your computer from your display. It's the perfect solution for controlling a computer from wherever the adapter is located.
The IP video extender helps you boost your office productivity, by making it easier for users to collaborate and communicate. The included software lets you connect multiple computers and easily switch between which user is sharing their content with the HDMI display, unlike some wireless video systems that are difficult to configure and require users to disconnect and reconnect manually.
With this IP video extender, you can turn your HDMI television, monitor or projector into an IP display that can connect to any Windows® computer on your network, making it perfect for conference rooms and classrooms where different ideas are shared by users who bring their own computers.
With a built-in USB hub, you can use your computer to access two remote USB devices at your remote display, enabling you or your customers to control the computer from the remote location. Remote operation can be used to create interactive digital signage, to engage your customers.
The IPUSB2HD3 is TAA compliant backed by a 2-year StarTech.com warranty with free lifetime technical support.
Note: This HDMI over IP video extender is intended for use on networks with dedicated bandwidth. See our FAQ for further details.
|Warranty Information||Warranty||2 Years|
|Connector(s)||1 - Connector A||HDMI (19 pin)|
|2 - Connector A||USB Type-A (4 pin) USB 2.0|
|1 - Connector B||USB B (4 pin)|
|Cabling||Cat 5e UTP or better|
|Chipset ID||DisplayLink - DL-195|
|Packaging Information||Package Height||66 mm [2,6 in]|
|Package Length||14,3 cm [5,6 in]|
|Shipping (Package) Weight||702 g [24,8 oz]|
|Package Width||17 cm [6,7 in]|
|Performance||Maximum Data Transfer Rate||USB - 480Mbps
Ethernet - 1000Mbps
|Max Distance||100 m / 330 ft|
|Maximum Digital Resolutions||1920x1080|
|Supported Resolutions||Widescreen (16/32 bit):
1920x1200, 1920x1080, 1680x1050, 1600x900, 1440x900, 1360x768, 1280x800, 1280x768, 1280x720
1600x1200, 1400x1050, 1280x1024, 1280x960, 1152x864, 1024x768, 800x600
|Wide Screen Supported||Yes|
|Audio Specifications||Two channel stereo audio supported|
|General Specifications||This USB video adapter uses a DisplayLink family chipset. If you’re connecting this device to a computer along with additional USB video adapters or docking stations, please avoid using devices with a Trigger or Fresco family chipset.|
|Physical Characteristics||Weight of Product||304 g [10,7 oz]|
|Product Length||10,2 cm [4,0 in]|
|Product Width||74 mm [2,9 in]|
|Product Height||24 mm [0,9 in]|
|Power||Power Source||AC Adapter Included|
|Input Voltage||100 - 240 AC|
|Input Current||0.6 A|
|Output Voltage||5 DC|
|Output Current||2 A|
|Center Tip Polarity||Positive|
|Power Consumption (In Watts)||10|
|Software||OS Compatibility||Windows® 10, 8.1, 8, 7, Vista, XP|
|What's in the Box||1 - Included in Package||HDMI over IP extender|
|universal power adapter (NA, EU, UK, ANZ)|
|mounting screw kit|
|rubber foot set|
|quick start guide|
Create Ultra HD connections between your High Speed HDMI®-equipped devices
To get the highest quality signal from your source to your display when you use an HDMI extender, do the following:
Make sure that the HDMI versions of the source, extender, and destination are compatible. For example, if you require 3D support, make sure that all of the devices can support 3D over HDMI.
Use the least amount of adapters, splitters, or converters as possible. Each device that you use in your setup creates additional points of potential failure and creates more steps for an HDCP key to hop through, which may cause issues with older displays. For more information on HDCP, refer to the following FAQ: http://www.startech.com/faq/video_signal_converters_HDCP.
Use an HDMI extender that exceeds the requirements of the setup. For example, if you need to extend the signal 200 feet, it is best to use an extender capable of more than 200 feet.
Make sure that all of the CAT 5/6 runs are as straight as possible, with the least amount of coiling.
Make sure that all of the patches, wall jacks, and cables use the highest possible CAT specification, (for example, CAT 6), and were tested to conform to the standard.
Use patches, wall jacks, and cables with the same pin configuration. For more information on T568A versus T568B wiring, refer to the following FAQ: http://www.startech.com/faq/network_cables_a_vs_b_pinout.
Keep the cabling away from sources of high noise.
Make sure that you use adequate electrical grounding in your setup.
Computers running macOS Catalina (10.15) may experience compatibility issues with products that use DisplayLink technology, such as USB Docking Stations and Video Adapters. Connecting to a DisplayLink-powered Product may cause the Display(s) to output a blank screen. If you experience this problem, follow these steps:
When you troubleshoot issues with a video extender, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
Video and Ethernet cables
Video source (such as a DVD player or computer)
Video destination (such as a monitor or projector)
Note: When you are testing setup components, you should avoid using video adapters. For example, if you are converting a VGA source to HDMI for use with an HDMI extender, you should use an HDMI source when you test the components.
To test your setup components, try the following:
Use the cable, video extender, video source, and video destination in another setup to see if the problem is with the components or the setup.
Use a different cable, video extender, video source, and video destination in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.
When you test your cables, it is recommended that you do the following:
Test each cable individually.
Use short cables when you are testing.
When you test the video source and video destination, it is recommended that you do the following:
Remove the video extender from your setup and test to make sure that the video source and video destination work together without the video extender.
Test to make sure that the video source and video destination work together at the resolution that you want to use.
Note: In order for your setup to work properly, the video source, extender, and destination all need to support the resolution that you are using.
If the IP extender detects that it does not have the necessary bandwidth to function, it may disconnect from the network. It is recommended that you use the IP extender with a switch or router with no other networking devices connected to it.
If the IP extender outputs video at 1920x1080, it can use up to 136Mbps. If the IP extender outputs video at 1920x1080 and remote USB devices are connected it, the IP extender can use up to 275Mbps.
Make sure that your network can support the bandwidth required by the IP extender.