StarTech.com

4-bay USB 3.0 eSATA naar SATA standalone 1:3 docking station

Dupliceer een SATA harde schijf naar drie harde schijven tegelijk

Productcode: SATDOCK4U3RE

  • Schijfduplicatie per sector, inclusief de HPA
  • Geïntegreerd LCD-scherm voor voortgangsindicatie en optiemenu
  • SuperSpeed USB 3.0-aansluiting met overdrachtsnelheden tot 5 Gbit/s
Bekijk meer
  • Snelle eSATA-aansluiting met overdrachtsnelheden tot 3 Gbit/s
  • Geïntegreerde functionaliteit voor het snel en veilig wissen van een schijf
  • Twee onder de schijven gemonteerde ventilatoren van 60mm met variabele snelheid (inclusief UIT)
  • Ondersteunt harde schijven (HDD) of solid-state drives (SSD) met een vormfactor van 2,5 of 3,5 inch
  • Compatibel met SATA harde schijven versie 1/2/3 (1,5/3,0/6,0 Gbit/s)
  • Gepatenteerd uitwerpmechanisme per knopdruk voor elk station
  • Onafhankelijke stroomschakelaars voor elke harde schijf
  • Extra, gemakkelijk toegankelijke ruimte tussen elke schijf
  • Vier grote, stabiele voeten met anti-slip
  • Inclusief SATA-naar-IDE-adapter
€ 588,99 EUR exc BTW
€ 712,68 EUR inc BTW

Overzicht

Met de SATDOCK4U3RE USB 3.0 en eSATA 1-naar-3 Harde Schijf Duplicator Docking Station als stand-alone apparaat kunt u een enkele SATA harde schijf dupliceren/klonen naar maximaal drie andere SATA-schijven tegelijk. De duplicator kan ook functioneren als een gewone 4-bay harde schijf docking station door deze aan te sluiten op een computersysteem. Er kunnen schijven met hoge capaciteit (getest tot 4TB 3,5" en 1TB 2,5" per bay) worden gebruikt om de opslag/backup-mogelijkheden van uw computer zeer te verbeteren.

De duplicator / docking station biedt 1:3 sectorduplicatie, inclusief HPA, van een enkele SATA-schijf naar drie andere tegelijk (met snelheden tot 72 Mbit/s), wat u tijd en moeite kan besparen. Als een externe harde schijf docking kan het worden aangesloten op uw computer via USB 3.0 of eSATA met overdrachtsnelheden tot respectievelijk 5 Gbit/s of 3 Gbit/s van de harde schijven naar uw computer .

Biedt functies voor snel en veilig wissen en ondersteuning voor IDE harde schijven met behulp van de meegeleverde SATA-naar-IDE-adapter (SAT2IDEADP).

StarTech.com Voordeel

  • Maakt tegelijkertijd 3 exacte kopieën van een SATA-schijf zonder aansluiting op een computer
  • Toegang tot 4 SATA harde schijven tegelijk via een enkele eSATA- of USB 3.0-aansluiting
  • Twee ventilatoren met variabele snelheid stellen u in staat de sterkte van de koeling aan te passen aan elke gebruiksomgeving of soort schijf

Toepassingen

Maak meerdere exacte kopieën van een harde schijf naar 3 nieuwe schijven voor de invoering van een groot aantal identieke computersystemen

Gerechtelijke technici die een of meer exacte kopieën van een harde schijf nodig hebben voor een onderzoek

MKB, OEM, systeemintegratoren, IT- en servicetechnici die snel toegang nodig hebben tot de inhoud van externe harde schijven, of de mogelijkheid om gegevens te klonen voor data-/schijfherstel.

Technische specificaties

Garantie
Garantie 2 Years
Hardware
Aantal stations 4
Chipsetcode JMicron - JMB394
JMicron - JMS539
Schijfgrootte 2.5in & 3.5in
Schijftype SATA
Ventilatoren 2 - 60 mm
Prestaties
Aantal plaatsingen 15,000 cycles per bay
Duplication Modes Sector by Sector (Whole Drive)
Duplication Speed 4.2GBpm
Max. schijfcapaciteit Tot nu toe getest met 3,5 inch harde schijven met 5400 rpm tot 4 TB (totaal 16 TB)en 2,5 inch harde schijven met 5400 rpm tot 1 TB (totaal 4 MB)
Maximale overdrachtsnelheid 3 Gbit/s
Port-multiplier Ja
Type en snelheid USB 3.0 - 5 Gbit/s
SATA II (3 Gbps)
Wismodi Quick Erase
Secure Erase (NIST SP 800-88 Rev 1 - Purge)
Connector(en)
Hostaansluitingen 1 - eSATA (7-polig, data) Contact
1 - USB Type-B (9-polig) USB 3.0 Vrouwelijk
Schijfaansluitingen 4 - SATA data & voeding combinatie (7+15-polig) Contact
Software
Besturingssystemen OS independent; No software or drivers required
Indicatoren
LED-indicatoren 4 - Schijf power/activiteit
Voeding
Inclusief voedingsadapter Inclusief wisselstroomadapter
Ingangsspanning 110V-240V AC
Ingangsstroom 2.0 A
Uitgangsspanning 12 DC
Uitgangsstroom 6.5 A
Vermogensopname 78
Gebruiksomgeving
Bedrijfstemperatuur 5°C to 80°C (41°F to 176°F)
Opslagtemperatuur -40°C to 70°C (-40°F to 158°F)
Vochtigheid 8% - 90% rel. luchtvochtigheid
Fysieke eigenschappen
Breedte product 172 mm [6.8 in]
Gewicht product 1.1 kg [2.4 lb]
Hoogte product 96 mm [3.8 in]
Kleur Zwart
Lengte product 284 mm [11.2 in]
Type behuizing Kunststof
Verpakkingsinformatie
Verzendgewicht (verpakt) 2.7 kg [6 lb]
Wat wordt er meegeleverd
Meegeleverd 1 - SATA-duplicator docking station
1 - SATA naar IDE adapter
1 - 40-pins IDE-kabel
1 - 44-pins naar 40-pins IDE-kabel
1 - eSATA-kabel
1 - Pakje met montageschroeven
1 - SP4 naar LP4 voedingskabel
1 - USB 3.0-kabel
1 - universele voedingsadapter (N-A/JP, VK, EU, ANZ)
1 - Handleiding

Compatibiliteit

Bekijk volledige OS compatibiliteit
OS independent; No software or drivers required

Certificaties

Verwante producten

USB naar IDE Standalone Schijf-Duplicator Docking Station
UNIDUPDOCK
USB naar IDE Standalone Schijf-Duplicator Docking Station

Kloon willekeurige combinatie van 2,5 of 3,5 inch IDE- of SATA-harde schijven

€ 263,99 exc BTW
€ 319,43 inc BTW

Accessoires

Productondersteuning

Veelgestelde vragen (FAQ)

Voor uw aanschaf

StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.

If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.

Solid-state drives (SSDs) use SATA connectors to access power and transfer data. Any duplicator that can copy to or from SATA hard drives will work with a StarTech.com duplicator.

Note: If you use a dock to duplicate SSDs, keep in mind that the StarTech.com disk duplicators execute a sector by sector read and write. SSDs are rated by a number of reads and writes. Repeated duplication and sector by sector reads and writes of SSDs can reduce the life cycle of the drive.

Software-level encryption on the drive poses no issue to StarTech.com duplicators, as the duplicators copy encrypted data sector by sector over to the new drive.

Hardware-level encryption or BIOS level hard drive locks cause the duplication to halt and fail, as the drive is unable to read or write the sectors that are encrypted.

Duplication of Hidden Protected Area (HPA) Partitions or Extended Industry Standard Architecture (EISA) cause the duplicator to halt and fail, as the drive cannot read and write the protected partitions on the drive.

Note: Our UNIDUPDOCKSATDOCK22RE and SATDOCK4U3RE do include the ability to copy HPA partitions, but the duplication is still dependent on how the HPA partition is written to the hard drive, whether or not it is encrypted and how it is encrypted.

StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.

SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.

Quick and secure erase functions

Quick erase and secure erase are functions the duplicators call on the hard drives themselves. How they work depends on the manufacturer of the hard drive.

Department of Defense erase function

A Department of Defense (DoD) erase is a function performed by the duplicator where it does three passes. The first pass writes all 0s. The second pass writes all 1s. The third pass writes 0s and 1s randomly.

Note: Not all duplicators will feature all of these erase modes. It is important to review the product manual to confirm the available erase modes.

To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the device supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the device was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the device. For example, IDE, SATA, or M.2.
  • Make sure that the device supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the device. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the docking station.

Hoe gaat u te werk

To confirm that the Mac OS detects your USB device, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your USB device is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

You may need to refresh the System Information page after you plug in your device.  To do so, press Command R with the System Information page open.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Troubleshooting

When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables
  • Hard drives
  • Hard drive dock or duplicator

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive dock or duplicator in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive dock or duplicator in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:

Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  2. Do one of the following:
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive. 

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

This docking station allows the hard drive to enforce its own power state, as opposed to enforcing a power state that keeps the hard drive active at all times. Since most newer hard drives have low-power energy conservation modes, this will cause the hard drive to enter an idle state if it is not used for a certain amount of time. 

 

You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.

The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.

Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.

Extend a partition on a computer running Windows

Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.

After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:

  1. Press the Windows key + R.
  2. Type compmgmt.msc and click Ok.
  3. In Computer Management, on the left side of the screen, click Disk Management.
  4. Find the target drive. It will most likely be at the bottom of the list, have a partition that is the same size as the source drive, and have an unallocated area on the drive.
  5. On the target drive, right-click the last partition on the right side of the screen and click Extend Volume.
  6. In the Extend Volume wizard, click Next. By default, the remaining drive area is the amount of space used.
  7. Click Next > Finish.

The primary partition on the drive now uses the entire drive area.

You can use the SATDOCK4U3RE to skip bad sectors on a hard drive. For more information, visit the following FAQ: http://www.startech.com/ca/faq/hard_drive_duplicators_failing_drives.

To use the SATDOCK4U3RE to skip bad sectors, you need to enable Read Error Skip. By default, Read Error Skip is disabled.

To enable Read Error Skip, complete the following:

  1. Turn on the SATDOCK4U3RE.

  2. Press ENT four times to enable Duplicator mode.

  3. Press ESC to open the menu.

  4. Press UP to open the Advanced Setup menu.

  5.  Press ENT twice to open the ReadErr Skip menu.

  6. Select Enable and then press ENT twice.

  7. Wait a few seconds for the unit to exit the menu.

StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode .  A duplication that fails or halts will not cause a problem with the source drive.

You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.