Product ID: PIB2MS1
Increase the data storage capacity of your Raspberry Pi or other development board, by connecting it directly to an mSATA drive. Perfect for custom projects and applications, this USB to mSATA converter supports all models of Raspberry Pi as well as other development boards.
This convenient USB 2.0 mSATA converter lets you overcome data storage limitations by enabling you to connect an mSATA drive through your board’s USB-A port.
The USB to mSATA converter integrates seamlessly with your existing development board. It’s the perfect addition for development-board based applications such as surveillance, media players and servers, digital signage and IoT/automation solutions. It allows you to utilize your mSATA drives with your development board, and take advantage of the small form factor of mini-SATA, ideal for applications with space limitations.
Compatible with SATA I, SATA II and SATA III drives, the converter is easy to install and doesn’t require any device driver installation. It comes with a USB cable and all mounting accessories, including standoffs, so integrating it with your Raspberry Pi is fast and easy.
StarTech.com provides industry-leading support to get you up and running quickly. The PIB2MS1 is backed by a StarTech.com 2-year warranty and free lifetime technical support.
Raspberry Pi is a trademark of the Raspberry Pi Foundation
|Warranty Information||Warranty||2 Years|
|Connector(s)||1 - Drive Connectors||mSATA (52 pin, Mini SATA) Slot|
|1 - Host Connectors||USB Micro-B (5 pin)|
|Environmental||Operating Temperature||5°C to 50°C (41°F to 122°F)|
|Storage Temperature||-25°C to 70°C (-13°F to 158°F)|
|Humidity||15% ~ 90% RH|
|Bus Type||USB 2.0|
|Number of Drives||1|
|Drive Size||mSATA (Full Size)|
|Compatible Drive Types||mSATA (Mini SATA)|
|Chipset ID||Renesas/NEC - µPD720231A|
|Packaging Information||Package Height||32.0 mm [1.3 in]|
|Package Length||17.5 cm [6.9 in]|
|Shipping (Package) Weight||100.0 g [3.5 oz]|
|Package Width||14.4 cm [5.7 in]|
|Performance||Maximum Data Transfer Rate||480 Mbps|
|Type and Rate||USB 2.0 - 480 Mbit/s|
|SATA III (6 Gbps)|
|Hardware Raid Supported||No|
|Product Length||65.0 mm [2.6 in]|
|Product Width||55.0 mm [2.2 in]|
|Product Height||1.1 cm [0.4 in]|
|Weight of Product||18.2 g [0.6 oz]|
|Software||OS Compatibility||OS independent; No software or drivers required|
|What's in the Box||1 - Included in Package||USB to mSATA converter|
|USB-A to Micro-B cable|
|4 - Included in Package||standoffs|
|2 - Included in Package||mSATA mounting screws|
When you troubleshoot issues with a hard drive controller card, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
IDE, SATA, and eSATA cables
Hard drive controller card
To test your setup components, try the following:
Use the IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in another setup to see if the problem is with the components or the setup.
Use a different IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.
When you test your cables, it is recommended that you do the following:
Test each cable individually.
Use short cables when you are testing.
When you test the hard drive and hard drive controller card, it is recommended that you do the following:
To open the Device Manager, press the Windows key + R, type devmgmt.msc, and press Enter. Check the IDE ATA/ATAPI controllers (for IDE) section, or the Storage controllers (for SATA) section.
Do one of the following:
If you do not see the hard drive controller card in Device Manager, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=expansion-cards#pci-pcie-cannot-boot-os-or-detect-windows.
If the device is listed with an error, reinstall the drivers by completing the instructions on the website.
If the hard drive is listed with unallocated space, the hard drive needs to be formatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.
Note: A formatted hard drive does not show up in Computer or My Computer until it has a drive letter assigned to it.