StarTech.com

USB-C naar dual Gigabit Ethernet adapter met USB (Type-A) poort

Gebruik de USB-C poort van uw laptop voor het toevoegen van LAN-toegang met twee gigabit Ethernet-poorten en een USB 3.0 (type-A) poort

Productcode: US1GC301AU2R

  • Voeg twee gigabit Ethernet-poorten toe aan uw laptop of desktop via een USB Type-C poort
  • Voeg een USB Type-A poort toe aan uw computer voor de aansluiting van een extra randapparaat
  • Is geschikt voor de nieuwste MacBook, Chromebook Pixel™ en andere laptop- en desktopcomputers met een USB-C poort (poort compatibel met Thunderbolt 3)
Bekijk meer
  • Met USB-voeding, compact en lichtgewicht voor maximale mobiliteit
  • Ondersteunt IEEE 802.3az Energy Efficient Ethernet, IEEE 802.3, 802.3u en 802.3ab (10BASE-T, 100BASE-TX en 1000BASE-T)
  • Tot 4K Jumbo Frame ondersteuning
  • Crossover-detectie en automatische aanpassing (Auto MDI-X)
€ 90,99 EUR exc BTW
€ 110,10 EUR inc BTW

Overzicht

Nu kunt u vaste netwerktoegang toevoegen via de USB-C™ of Thunderbolt™ 3 poort van uw laptop of desktop en eenvoudig verbinding maken met uw USB 3.0 (Type-A) apparaten. Deze gigabit Ethernet netwerkadapter biedt u toegang tot twee betrouwbare GbE-poorten, en zonder stuurprogramma's te moeten installeren. Deze netwerkadapter is een geweldige metgezel voor uw MacBook, Chromebook Pixel™, Dell™ XPS 12, Dell Latitude™ 12 7000 Serie 2-in-1 of ander apparaat met een USB Type-C™ poort.

Krachtige gigabit netwerkverbindingen

De netwerkadapter benut de 5 Gbps snelheid van USB 3.0 (ook bekend als USB 3.1 Gen 1) en biedt zo de volledige bandbreedte van uw gigabit netwerkverbinding, zonder knelpunten. Dit bespaart u tijd omdat u gemakkelijker toegang hebt tot zeer grote bestanden via het netwerk met gigabitsnelheden. 

Voor nog meer veelzijdigheid ondersteunt de netwerkadapter een scala aan handige functies zoals Wake-On-LAN, VLAN Tagging, Crossover Detection en Auto-Correction (Auto MDIX), Checksum Offload (IPv4, IPv6, TCP, UDP) en Large Send Offload.

Voeg connectiviteit toe aan uw USB-apparaten

Sommige computers met USB Type-C bieden slechts één USB-C poort voor externe aansluitingen, waarop u uw bestaande USB Type-A apparaten echter niet kunt aansluiten. Deze gigabit adapter heeft een geïntegreerde USB 3.0 Type-A poort, zodat u - terwijl de adapter op uw computer is aangesloten voor netwerktoegang - ook verbinding kunt maken met USB-randapparaten waarvoor een USB Type-A connector nodig is. De netwerkadapter is ook neerwaarts compatibel met USB 2.0 systemen.

Eenvoudige installatie dankzij native stuurprogrammaondersteuning

Gebruiksklaar in een mum van tijd. De netwerkadapter biedt native stuurprogrammaondersteuning voor een snelle installatie. Steek de adapter gewoon in de USB Type-C poort van uw laptop en maak verbinding met uw netwerk. De netwerkadapter chipset biedt native stuurprogrammaondersteuning in Chrome OS™ en Windows® 8.1, en ondersteunt Mac OSX (10.10) met stuurprogramma-installatie.

Probleemloze verbindingen via USB-Type-C

De USB Type-C connector is kleiner en gemakkelijker te gebruiken dan vorige USB connectors. Dankzij het omkeerbare design kunt u deze connector in uw apparaten steken ongeacht welke kant omhoogwijst. Sluit de kabel telkens correct aan - frustratie of beschadigde poorten behoren tot het verleden.

De US1GC301AU2R wordt gedekt door een 2-jarige garantie en gratis levenslange technische ondersteuning van StarTech.com.

Toepassingen

Voeg gigabit Ethernet-capaciteit toe aan uw MacBook, Chromebook Pixel, Dell XPS 12 of Dell Latitude 12 7000 Series 2-in-1

Voeg een extra USB-randapparaat toe met uw netwerkadapter

Verbeter uw laptop of desktop met gigabit netwerkmogelijkheden zonder de computer te hoeven openen of een beschikbare uitbreidingssleuf te gebruiken

Sluit uw laptop aan op een gigabit netwerk - ideaal voor kleine bedrijven, thuiskantoren, netwerkprogramma's op afdelingen en netwerk gaming

Technische specificaties

Garantie
Garantie 2 Years
Hardware
Bus type USB 3.0
Chipsetcode VIA/VLI - VL812
ASIX - AX88179
Industriestandaarden IEEE 802.3, 802.3u en 802.3ab
Interface RJ45 (gigabit Ethernet)
Poorten 2
USB pass-through Ja
Prestaties
Auto MDIX Ja
Bandbreedte 5 Gbps (USB 3.0)
2 Gbps (Ethernet - Full-Duplex)
Compatibele netwerken 10/100/1000 Mbps
Full duplex ondersteuning Ja
Jumbo Frame Support 4K max.
Maximale kabellengte 0.1 m [0.3 ft]
Maximale overdrachtsnelheid 5 Gbps (USB 3.0)
2 Gbps (Ethernet; full-duplex)
Type en snelheid USB 3.0 - 5 Gbit/s
Connector(en)
Externe poorten 2 - RJ-45 Vrouwelijk
Type connector(en) 1 - USB 3.0 A (snelladen, 9-polig, SuperSpeed)
1 - USB Type-C (24-polig) USB 3.0
Software
Besturingssystemen Windows® XP, Vista, 7, 8, 8.1, 10
Windows Server® 2003, 2008 R2, 2012, 2016
Mac OS® 10.6 to 10.13 VLAN tagging is currently not supported in Mac OS
Linux Kernel 2.6.25 to 4.11.x LTS Versions only
Speciale opmerkingen / vereisten
Systeem- en kabelvereisten Beschikbare USB Type-C poort
Indicatoren
LED-indicatoren 4 - 2x Gigabit koppeling/activiteit

2x 10/100 koppeling/activiteit
Voeding
Inclusief voedingsadapter Gevoed via USB
Gebruiksomgeving
Bedrijfstemperatuur 5°C to 50°C (41°F to 122°F)
Opslagtemperatuur -20°C to 60°C (-4°F to 140°F)
Vochtigheid 20%~80%
Fysieke eigenschappen
Breedte product 60 mm [2.4 in]
Form Factor Aangesloten kabel
Gewicht product 54 g [1.9 oz]
Hoogte product 16 mm [0.6 in]
Kleur Zwart
Lengte product 75 mm [3 in]
Type behuizing Kunststof
Verpakkingsinformatie
Verzendgewicht (verpakt) 112 g [4 oz]
Wat wordt er meegeleverd
Meegeleverd 1 - USB-C naar dual gigabit Ethernet-adapter

Compatibiliteit

Bekijk volledige OS compatibiliteit
Windows® XP, Vista, 7, 8, 8.1, 10
Windows Server® 2003, 2008 R2, 2012, 2016
Mac OS® 10.6 to 10.13 VLAN tagging is currently not supported in Mac OS
Linux Kernel 2.6.25 to 4.11.x LTS Versions only

Certificaties

Verwante producten

USB-C naar gigabit netwerkadapter met extra USB poort
US1GC301AU
USB-C naar gigabit netwerkadapter met extra USB poort

Gebruik de USB Type-C poort van uw laptop om een gigabit Ethernet-poort en een USB 3.1 Gen 1 (Type-A) poort toe te voegen

€ 58,99 exc BTW
€ 71,38 inc BTW
USB 3.0 naar Gigabit Ethernet Netwerkadapter
USB31000S
USB 3.0 naar Gigabit Ethernet Netwerkadapter

Voeg Gigabit Ethernet-netwerkconnectiviteit toe aan een laptop of pc via een USB 3.0-poort

€ 32,99 exc BTW
€ 39,92 inc BTW
USB-C naar Gigabit Ethernet Netwerkadapter
US1GC30B
USB-C naar Gigabit Ethernet Netwerkadapter

Sluit een gigabit netwerk via de USB-C poort aan op uw computer.

€ 38,99 exc BTW
€ 47,18 inc BTW
USB-C naar gigabit netwerkadapter - Wit
US1GC30W
USB-C naar gigabit netwerkadapter - Wit

Voeg een gigabit Ethernet-poort toe aan uw MacBook, Chromebook of laptop met USB Type-C

€ 38,99 exc BTW
€ 47,18 inc BTW

Accessoires

Productondersteuning

Veelgestelde vragen (FAQ)

Voor uw aanschaf

USB-C is a type of USB connector that is capable of supporting the following:

  • Data transfer speeds up to 10Gbps, if you use USB 3.1.
  • Bi-directional power delivery up to 100W, if both the USB host connection and the device support it.
  • Alternate modes, which deliver different types of data at different speeds. For example, DisplayPort Alternate Mode (DP Alt Mode).

If using Thunderbolt 3 over USB-C, the connection is capable of additional features. For example, Thunderbolt 3 is capable of 40Gbps of total bandwidth. For more information, refer to the following FAQ: https://www.startech.com/faq/thunderbolt-3-port-capabilities.

Not all USB-C ports or devices are capable of supporting all of the features listed above, or all of the features at the maximum capabilities. If you require a specific USB-C feature, your USB host connection, cables, and device must all support the feature that you require. For more information about whether your components support specific USB-C features, refer to the information provided by the manufacturers. 

Hoe gaat u te werk

StarTech.com does not support a Preboot Execution Environment (PXE) as this requires third-party software. However, our devices can be used as long as the following conditions are met:

  1. The BIOS must support PXE.
  2. The BIOS must see the card.
  3. The environment must have drivers for the chipset used in the card.
  4. If using a USB networking card, the environment must have support for USB devices as well.

Virtual local area network (VLAN) tagging requires that the network interface card (NIC) and the router or switch that you use support protocol IEEE 802.1q.

Depending on the NIC, you can set your VLAN ID in Device Manager.  Not all NICs that support VLAN tagging have this option.

Setting your VLAN ID in Device Manager

Note: Log in as the local administrator before continuing.

To open Device Manager:

  • Press Windows key + R
  • Type devmgmt.msc
  • Click OK.
  1. In Device Manager, open Network adapters.
  2. Right-click on the NIC and choose Properties.
  3. Click the Advanced tab.
  4. Scroll down to VLAN ID.
  5. Set the ID that you would like the NIC to have and click OK.

Setting up your VLAN Tagging and Setting a VLAN ID

How you perform this task depends on your router or switch.  Consult the manual or manufacturer of your router or switch for more details.

In your router or switch, you can VLAN tag a device by the VLAN ID if you set one previously, or by the MAC address of the computer.  Your router or switch will list all IP devices by MAC address.

For most operating systems, network interface card (NIC) teaming requires that the NIC and the router or switch support the protocol IEEE 802.1ax or IEEE 802.3ad. 

Windows Server 2012, however, has native support for NIC teaming, so the NIC and the router or switch do not need to support the protocols. To configure NIC teaming in Windows Server 2012 do the following:

  1. Click Start.
  2. Click Server Management.
  3. Click NIC Teaming enabled.
  4. Set up the NIC team as you would like.

If you view the Networking Connections section in the window, you can see the NIC team in the list as well as the Ethernet and wireless adapter cards.

Troubleshooting

When you troubleshoot issues with a network adapter, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Ethernet cables
  • Network devices
  • Computer system

To test your setup components, try the following:

  • Use the Ethernet cables, network devices, and computer system in another setup to see if the problem is with the components or the setup.
  • Use different Ethernet cables, network devices, and a different computer system in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.
  • Use short cables when you are testing.

When you test the Ethernet cables, network devices, and computer system, it is recommended that you do the following:

Sometimes an on-board network interface card (NIC) conflicts with a new NIC.  In these cases it is best to disable the on-board NIC.

The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible.  To do this, consult your motherboard manual.

You can also disable any NIC in Windows.  Here is how you do this:

First click Start, or, in Windows 10 and 8, hold down the Windows key and press X.  Then click Control Panel.

Windows 10

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows 8

  1. Click Network and Sharing Center.
  2. On the left, click Change adapter settings.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows 7

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows Vista

  1. Click Network and Sharing Center.
  2. On the left, click Manage network connections.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows XP

  1. Click Network Connections.
  2. Right-click the NIC that you would like to disable and select Disable.

If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings.  You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

Note: You must log in as the local administrator before you continue.

To open Device Manager:

  • Press Windows key + R.
  • Type devmgmt.msc.
  • Click OK.
  1. Open the Networking adapters section.
  2. Right-click the network adapter that you want to change and select Properties.
  3. Click the Advanced tab.
  4. Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate. Select any of the speeds that you see in the list.
  5. Click OK and restart your computer.

If the USB device does not work after your computer has been in extended hibernation, it is likely that Windows has automatically turned off the USB Root hub to save power. 

The steps below outline how to configure the USB root hub to stay on during hibernation, to prevent this from happening.
 

Windows 10 / 8

  1. On your keyboard, press the Windows key + X and select Control Panel.
  2. Click Hardware and Sound, then click Power Options.
  3. Click Change plan settings for the plan you want to change.
  4. Click Change advanced power settings.
  5. Click the plus sign (+) next to “USB settings” and “USB selective suspend setting” to expand the options and change the setting to Disabled.
  6. Click OK to apply the setting.

Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.

Windows 7 / Vista

  1. Click the Start button and select Control Panel.
  2. Click Hardware and Sound, then click Power Options.
  3. Click Change plan settings for the plan you want to change.
  4. Click Change advanced power settings.
  5. Click the plus sign (+) next to “USB settings” and “USB selective suspend setting” to expand the options and change the setting to Disabled.
  6. Click OK to apply the setting.

Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.

Windows XP

  1. On your desktop, right-click the My Computer icon and select Properties.
  2. Click the Device Manager tab.
  3. Expand Universal Serial Bus controllers by clicking the arrow to the left of it.
  4. Right-click the first USB Root Hub device and select Properties.
  5. Click the Power Management tab.
  6. Clear the box next to Allow the computer to turn off this device to save power.
  7. Click OK to apply the setting.
  8. Repeat steps 4-7 for any remaining devices in the Universal Serial Bus Controllers section with “Root Hub” in the name.

Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.