Product ID: DSRXL
In stock: 8
StarTech.com's DS Series Digital Signage Broadcaster VGA Cat5 Receiver offers a comprehensive audio and video extension system, with the added benefit of serial control!
The DSRXL VGA Receiver(s) can be installed at the destination points, allowing you to distribute VGA video as well as the accompanying audio and serial control signals from the connected Serial, Audio and VGA Cat5 Digital Signage Broadcaster (DS128 - purchased separately), all over one Cat5 cable.
Ensuring not only a simple and cost-effective way to extend and control VGA video and the corresponding audio, the DS series (DS128 and DSRXL) also maintains exceptional, high quality video, up to 1600x1200 over a 100m connection. For further extension, you can daisy chain up to five receivers, for a maximum distance of 300m.
|Warranty Information||Warranty||2 Years|
|Connector(s)||Remote Unit Connectors||2 - VGA (15 pin, High Density D-Sub)|
|2 - RJ-45|
|2 - 3.5 mm Mini-Jack (3 Position)|
|2 - DB-9 (9 pin, D-Sub)|
|Environmental||Operating Temperature||0°C to 40°C (32°F to 104°F)|
|Storage Temperature||-20°C to 60°C (-4°F to 140°F)|
|Cabling||Cat 5 UTP|
|Industry Standards||DDC/EDID Emulation for port 1 monitor|
|Packaging Information||Package Length||20.6 cm [8.1 in]|
|Package Width||14.5 cm [5.7 in]|
|Package Height||176 mm [6.9 in]|
|Shipping (Package) Weight||1.0 kg [2.3 lb]|
|Performance||Maximum Cable Length||10000.0|
|Max Distance||300 m / 950 ft|
|Maximum Analog Resolutions||1600x1200|
|Supported Resolutions||1600x1200 @ 100m(330ft)
1280x1024 @ 300m(950ft)
|Wide Screen Supported||Yes|
|Audio Specifications||Two channel stereo audio supported|
|Product Length||13.5 cm [5.3 in]|
|Product Width||132 mm [5.2 in]|
|Product Height||2.6 cm [1.0 in]|
|Weight of Product||526 g [18.6 oz]|
|Power||Power Source||AC Adapter Included|
|Output Voltage||5 DC|
|Center Tip Polarity||Positive|
|Power Consumption (In Watts)||10|
|Special Notes / Requirements||Note||Up to 5 receiver units can be daisy-chained from the broadcaster unit extending to a maximum distance of 300m|
|What's in the Box||Included in Package||1 - Digital Signage Receiver|
|2 - Mounting Brackets w/ Screws|
|1 - Universal Power Adapter (NA/UK/EU/AUS)|
|1 - Instruction Manual|
Extend and centrally manage VGA video, audio and RS232 control signals to multiple displays
In stock: 8
Replace your lost or failed power adapter
In stock: 22
Make Fast Ethernet network connections using this high quality Cat5e Cable, with Power-over-Ethernet capability
In stock: 84
Extend your VGA monitor connections by 6ft
In stock: 311
Extend your VGA monitor connections by 25ft
In stock: 23
Extend your VGA monitor connection without losing video signal quality
In stock: 59
Extend your VGA monitor connections by 100ft
In stock: 19
Connect your VGA monitor with the highest quality connection available
In stock: 558
Connect your VGA monitor with the highest quality connection available
In stock: 53
There are a few things you'll want to take care of before you deploy your new video extender in your setup.
It’s important to make sure you have everything you will need ahead of time. These items are listed below.
It’s also important to test everything in a simplified setup ahead of time to make sure everything works and that you understand how it works.
In order to set up your video extender, complete the following:
Note: Not all video extenders require external power, or require external power on both ends. Refer to the manual for more information.
Now that you have set up your video extender, you can check that everything is working. You should be able to see your video source's output on the display connected to the video receiver.
If at this point you have further questions regarding a Startech.com video extender, contact our technical support team for further assistance.
When you troubleshoot issues with a video extender, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
Video and Ethernet cables
Video source (such as a DVD player or computer)
Video destination (such as a monitor or projector)
Note: When you are testing setup components, you should avoid using video adapters. For example, if you are converting a VGA source to HDMI for use with an HDMI extender, you should use an HDMI source when you test the components.
To test your setup components, try the following:
Use the cable, video extender, video source, and video destination in another setup to see if the problem is with the components or the setup.
Use a different cable, video extender, video source, and video destination in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.
When you test your cables, it is recommended that you do the following:
Test each cable individually.
Use short cables when you are testing.
When you test the video source and video destination, it is recommended that you do the following:
Remove the video extender from your setup and test to make sure that the video source and video destination work together without the video extender.
Test to make sure that the video source and video destination work together at the resolution that you want to use.
Note: In order for your setup to work properly, the video source, extender, and destination all need to support the resolution that you are using.
The problem is usually a bad quality or damaged VGA cable on either end of the extender set. Try replacing the VGA cable with a higher quality cable like StarTech.com’s MXT101MMHQ.
You should only use video converters and extenders if it is absolutely necessary to do so. In many cases, most video converters and extenders are not necessary if you purchase the correct cable.
The following table lists the maximum length of cable for common video standards.
|Video standard||Maximum length|
|DisplayPort||50 ft. (15.2m)|
|HDMI||50 ft. (15.2m)|
|DVI||50 ft. (15.2m)|
|VGA||200 ft. (71m)|
Note: StarTech.com offers cables longer than what is listed above, including active cables, which typically include built-in active signal boosters that allow for longer cables. Active cables are specifically designed to exceed the suggested maximum lengths and are tested at the listed specifications (for example, the maximum listed resolution).
Video adapters passively adapt a cable from one connector type to another. Video adapters do not change the signal type, or change the video standard.
Examples of common applications for adapters include the following:
DVI-I to VGA
RCA to BNC
Mini DisplayPort to DisplayPort
Couplers (female to female, or male to male)
Note: You can use a coupler to extend a cable for a short distance. However, each coupler that you use can introduce signal loss, which degrades the signal quality.
Video converters actively process and change the signal type from one video standard and convert it to another standard. They are typically used to convert digital to analog and vice versa, but can be used to convert a digital signal to another digital video standard (for example, HDMI to DisplayPort).
Video converters work over short distances from the source to the destination: up to 15 feet or 3 meters.
Video extenders convert an input signal to a higher voltage for transmission over longer distances and then convert the input signal back to the original video standard. The input and the output signal will match on a video extender, as the same video standard is maintained end-to-end. If a cable is extended with adapters or converters, the signal quality degrades.
Note: For more information on using a video adapter or converter with a video extender, see the following FAQ: http://www.startech.com/faq/video_signal_converters_convert_then_extend.
If you need to use a video extender with a video adapter or converter, you should position the adapter or converter as close to the video source as possible. For example, if you need to take a VGA signal from a computer and send it 200 feet to an HDMI® projector, you should convert the signal from VGA to HDMI and use an HDMI extender.
Note: For more information on when to use cables or extenders, see the following FAQ: http://www.startech.com/faq/video_signal_converters_when_to_convert.
No, this device is designed to be a point-to-point solution using networking cabling only.
This device outputs a VGA signal. If you have a display or video destination that uses another type of video connection, there are ways that you can convert the video signal or connection. These options are outlined below and organized by the target connection.
|Target connection||First conversion||Second conversion (if required)|
|DVI-D||VGA to HDMI: https://www.startech.com/AV/Converters/Video/?filter_AVINPUT=VGA&filter_AVOUTPUT=HDMI.||HDMI to DVI-D: https://www.startech.com/AV/Converters/Video/?filter_AVINPUT=VGA&filter_AVOUTPUT=HDMI.|
|DVI-I||VGA to DVI-I: https://www.startech.com/Cables/Audio-Video/Video-Adapter/DVIVGA/.||N/A|
|DisplayPort||VGA to HDMI: https://www.startech.com/AV/Converters/Video/?filter_AVINPUT=VGA&filter_AVOUTPUT=HDMI.||HDMI to DisplayPort: https://www.startech.com/AV/Converters/Video/?filter_AVINPUT=HDMI&filter_AVOUTPUT=DisplayPort.|
Note: You might need to use more than one converter as part of your solution; however, you should try to use the least number of converters and cables to connect your source and destination. If you have the option to convert to multiple target video connections, choose the option that requires the fewest number of conversions.
When you convert from VGA to DVI, you need to know if you are converting to a DVI-I or a DVI-D connection. For more information about how to identify the type of connection that you need, refer to the following FAQ: https://www.startech.com/faq/video_signal_converters_dvi_interface.
You also need to know which form of DVI that you are using, because DVI-I supports both analog (VGA) and digital (HDMI) signals, while DVI-D only supports digital (HDMI) signals.
Note: Certain devices may have a DVI-I connection but only support DVI-D signaling. It is important to verify that your DVI-I device supports DVI-I signaling.
This device has a VGA input port. If you have a video source that uses another video connection, there are options available to convert the video signal or connection. These options will be outlined below for each video source connection.
DVI-I to VGA: https://www.startech.com/DVIVGAMFBK.
DisplayPort to VGA: https://www.startech.com/AV/Displayport-Converters/DP-VGA/.
When you convert from DVI to VGA, you need to know if you are converting from a DVI-I or a DVI-D connection. For more information about how to identify the type of connection that you have, refer to the following FAQ: https://www.startech.com/faq/video_signal_converters_dvi_interface.
You also need to know which form of DVI that you are using, because DVI-I supports both analog (VGA) and digital (HDMI) signals, while DVI-D only supports digital (HDMI) signals. Some DVI-I connections only support DVI-D signaling. In this case, you must use a DVI-D to VGA converter.