Product ID: HSB430SATBK
In stock: 1
This 4 Bay SATA Mobile Rack lets you swap between 3.5in Serial ATA (SATA, SATA II, SATA III-6Gbps) hard drives in seconds.
A time saving storage solution, the mobile rack offers four trayless SATA hard drive bays, allowing you to hot swap Serial ATA hard drives but avoid having to mount the drives to trays for deployment or unfasten them for replacement.
To maximize performance and utilize the full speed potential of your SATA III hard drives, this HDD Backplane supports SATA III for transfer speeds up to 6 Gbps when paired with a compatible controller.
Supporting up to four hard drives, the mobile SATA hot swap rack only takes up three 5.25in drive bays inside a host computer - maximizing space-efficiency within the computer. The mobile rack/backplane is fully compatible with RAID installations to ensure maximum performance and versatility for enhanced storage applications.
Using Terabyte hard drives? Don’t expose your Hard Drive and valuable data to unnecessary heat!
The HSB430SATBK has two built-in 40mm fans that re-distribute the heat build-up generated as a result of typical drive operation. This feature is especially important for larger volume storage drives, and faster “spinning" drives (i.e 7200 RPM), as it can help optimize drive operability and in turn preserve stored data integrity.
|Warranty Information||Warranty||2 Years|
|Connector(s)||4 - Drive Connectors||SATA (7 pin, Data)|
|SATA Power (15 pin)|
|4 - Host Connectors||SATA (7 pin, Data)|
|SATA Power (15 pin)|
|Environmental||Operating Temperature||0°C to 50°C (32°F to 122°F)|
|Storage Temperature||0°C to 50°C (32°F to 122°F)|
|Humidity||Operating - 5~85% RH Non-condensing
Storage - 5~95%
|Hardware||Number of Drives||4|
|Compatible Drive Types||SATA|
|2 - Fans||40 mm|
|Indicators||4 - LED Indicators||Drive Power|
|Packaging Information||Shipping (Package) Weight||1,4 kg [3,2 lb]|
|Package Length||27,0 cm [10,6 in]|
|Package Width||18,2 cm [7,2 in]|
|Package Height||21,8 cm [8,6 in]|
|Performance||Hot Swap Capability||Yes|
|Insertion Rating||10, 000+ Cycles|
|Noise Level||24 dBA|
|Physical Characteristics||Weight of Product||1,4 kg [3,2 lb]|
|Material||Aluminum and Plastic|
|Product Length||19,4 cm [7,6 in]|
|Product Width||14,6 cm [5,7 in]|
|Product Height||12,6 cm [5,0 in]|
|Software||OS Compatibility||OS independent; No software or drivers required|
|What's in the Box||1 - Included in Package||5.25" Tray-Less SATA Hot-Swap Bay|
|4 - Included in Package||SATA cable|
|SATA to LP4 Molex + LED Cable|
|1 - Included in Package||Screw kit|
When you troubleshoot issues with a hard drive rack, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
To test your setup components, try the following:
When you test the hard drive and hard drive rack, it is recommended that you do the following:
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.
Yes, this mobile rack does support hot-swapping of SATA drives. To use this feature, it is required that the SATA port is set to Advanced Host Controller Interface (AHCI) mode and hot-swapping is enabled. On most motherboards, this is performed within the Basic Input/Output System (BIOS) or the Unified Extensible Firmware Interface (UEFI). If you are using a SATA controller card, consult the motherboard manufacturer's technical documentation for the correct steps to accomplish this.