Product ID: MCMGBSC055EU
The MCMGBSC055EU 1000 Mbps Gigabit Multi Mode Fiber Ethernet Media Converter SC - 550m converts transparently to/from 1000Base-T Ethernet signals and 1000Base-SX optical signals, providing a cost-effective Ethernet-fiber/copper-fiber link, in order to extend an Ethernet network connection over a Multimode fiber backbone.
Supporting a maximum Multimode fiber optic cable distance of 550 meters (0.34 miles), this Fiber Media Converter delivers a simple solution for connecting Gigabit Ethernet networks to remote locations using SC-terminated MM fiber, while ensuring solid network performance and scalability.
Backed by a StarTech.com 2-year warranty and free lifetime technical support.
|Warranty Information||Warranty||2 Years|
|Connector(s)||1 - Local Unit Connectors||RJ-45|
|1 - Remote Unit Connectors||Fiber Optic SC Duplex|
|Environmental||Operating Temperature||0°C to 40°C (32°F to 104°F)|
|Storage Temperature||-10°C to 70°C (14°F to 158°F)|
|Industry Standards||IEEE 802.3z 1000BASE-SX|
|Indicators||1 - LED Indicators||FX Link: On - Valid Fiber Link|
|TP RX: On - Receiving Data on the Ethernet Link|
|TP Link: On - Valid Ethernet Link|
|Packaging Information||Package Length||20,5 cm [8,1 in]|
|Package Width||16,5 cm [6,5 in]|
|Package Height||68 mm [2,7 in]|
|Shipping (Package) Weight||450 g [15,9 oz]|
|Performance||Maximum Data Transfer Rate||1000 Mbps (1 Gbps)|
|Max Transfer Distance||550 m (1804 ft)|
|Fiber Operating Mode||Half/Full-Duplex|
|Product Length||99 mm [3,9 in]|
|Product Width||73 mm [2,9 in]|
|Product Height||27 mm [1,1 in]|
|Weight of Product||450 g [15,9 oz]|
|Power||Power Source||AC Adapter Included|
|Input Voltage||230 AC|
|Output Voltage||9V DC|
|Output Current||0.6 A|
|Center Tip Polarity||Positive|
|Power Consumption (In Watts)||5.4|
|What's in the Box||1 - Included in Package||Media Converter|
Make Fast Ethernet network connections using this high quality Cat5e Cable, with Power-over-Ethernet capability
Replace your lost or failed power adapter
When you troubleshoot issues with a fiber media converter, there are some quick tests that you can complete to rule out potential problems. To identify what the source of the issue is, observe the power LED, LAN LEDs, and fiber link LED on the units.
If the power LED is not illuminated for the transmitter or the receiver, complete the following:
Make sure that you are using the provided power adapter(s).
Make sure that the adapter is plugged into a compatible wall outlet.
Make sure that the adapter is plugged into both the transmitter and receiver.
If another LED is not operating as expected, make sure that the components in your setup are working correctly. To test your setup components, try the following:
Use the cables, fiber media converter, and network devices (including SFPs, if applicable) in another setup to see if the problem is with the components or the setup.
Use different cables, fiber media converter, and network devices (including SFPs, if applicable) in your setup to see if the problem persists. Ideally, you should test components that you know work in another setup.
When you test your cables, it is recommended that you do the following:
Test each cable individually.
Use short cables when you are testing.
Make sure that the DIP switches are set to the following:
DIP switches should be identical on both local and remote units. By default, DIP switches are set to Off (the switch is pointing up).
For more information about the advanced configuration options, refer to the manual for your product.
If you cannot establish a network connection between your local and remote units, you need to do the following to make sure that the issue is not related to the network configuration:
Use two computer systems directly connected to the fiber media converter LAN ports.
Open a command prompt on Computer 1 and ping Computer 2.
If the issue is not related to the network configuration, you should receive a response from Computer 2.
For more information on how to ping another network device, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=networking#ping-test-windows-mac-os.
Different optical cables are needed for different applications. Before you select a cable to interconnect fiber devices, make sure that the following things match:
Mode: Single Mode or Multi Mode.
Wavelength: For example, 850 nm, 1310 nm, or 1550 nm.
Note: The above properties cannot be converted or changed by a cable.
When you select a cable, make sure that the cable ends (for example, LC, SC, ST, or MT) match the fiber media devices.
Simplex and duplex ends are available for most connector types. Simplex cables have the connectors separate, where duplex cables have the transmit (TX) and receive (RX) connectors joined together. StarTech.com fiber media devices are compatible with simplex and duplex connectors.
It does not matter which diameter or OM classification the cable uses, as long as it meets the mode requirement.
Fiber media converters can be used to convert a standard Ethernet connection to a standard fiber connection, or can be used to extend a copper Ethernet network. When you use fiber media converters to extend a copper Ethernet network, make sure that the same fiber standards are being used on either end of the fiber network.
UPC and APC are fiber connector types. UPC (Ultra Physical Contact) connectors have a fiber connector end face that has been polished to a dome-shape. APC (Angled Physical Contact) connectors have a fiber connector end face that has been polished at an eight degree angle. When building fiber solutions, be sure to avoid mixing UPC and APC connectors. UPC and APC cannot mate with one another because causes the fiber cores don’t touch. This can cause a degraded connection or none at all.
StarTech.com fiber products use UPC connectors.