USB 3.1 (10 Gbps) gereedschapsloze behuizing voor 2,5 inch SATA-schijven

Benut de hogere snelheid van USB 3.1 Gen 2 in een lichte en draagbare opslagoplossing

Productcode: S251BPU313

  • Creëer een draagbare externe opslag voor een 2,5 inch SSD/HDD met USB 3.1 Gen 2 high-speed prestaties
  • Gereedschapsloos ontwerp en lichte behuizing voor eenvoudige mobiliteit
  • USB A-naar-Micro B-kabel voor gemakkelijke compatibiliteit
Uw prijs
€36,99 EUR excl. VAT
€44,76 EUR incl. VAT

Nu hebt u zoals nog nooit tevoren toegang tot uw data, waar u ook heen gaat. Deze USB 3.1 Gen 2 (10 Gbps) 1-schijfsbehuizing voor 2,5 inch solid-state of harde schijven biedt u een ultrasnelle, draagbare externe opslagoplossing.

Foto van StarTech.com USB 3.1 Gen 2 behuizing (S251BPU313) op laptoptas, waaruit blijkt hoe mobiel hij is

Licht en gereedschapsloos voor eenvoudige mobiliteit

Ontworpen met een duurzaam en licht frame, past deze behuizing gemakkelijk in een laptop- of draagtas voor mobiele opslag. Het is volledig gereedschapsloos en kan dus snel in uw schijven worden geïnstalleerd.

Benut de snelheid van USB 3.1 Gen 2

Tabel met USB-bestandstransmissiesnelheden toont USB 3.1 Gen 2 met 10 Gbps is twee keer zo snel als USB 3.0 met 5 Gbps

USB 3.1 Gen 2 biedt u meer bandbreedte en snelheid, met bestandstransmissiesnelheden tot 10 Gbps - twee keer zo snel als USB 3.0 (USB 3.1 Gen 1). Daardoor kunt u de hoge prestaties van de laatste SSD's benutten, terwijl knelpunten in uw datatransmissie worden opgelost.

Direct gevoed vanaf de USB-poort

De behuizing kan eenvoudig worden aangesloten op een hostcomputer, zonder dat een externe voeding vereist is. Het wordt geleverd met een USB A-naar-Micro B-kabel, waardoor het neerwaarts compatibel is met bestaande USB-poorten of hardware. Verder wordt UASP ondersteund voor nog betere prestaties.

De S251BPU313 wordt gedekt door een 2-jarige garantie en gratis levenslange technische ondersteuning van StarTech.com.

Toepassingen

  • Profiteer van nieuwe laptops en desktops met een ultrasnelle USB 3.1 Gen 2 (10 Gbps) verbinding
  • Snelle en draagbare externe opslag voor laptops, netbooks of pc’s
  • Gebruik uw SATA SSDs/HDDs met maximale snelheid
  • Back-up belangrijke data naar een extern opslagapparaat
  • Deel snel en veilig grote bestanden tussen computers onderling zonder een netwerk
  • Zet gegevens over vanuit uw oude SATA-schijf of zet een ongebruikte schijf om in extra externe opslagruimte

Partnernummers

  • Ingram Micro Belgium 2996000
  • Tech Data - Belgium 4428477
  • UPC 065030861946

Compatibility

Specificaties

Warranty Information Warranty 2 Years
Connector(en) 1 - Schijfaansluitingen SATA data & voeding combinatie (7+15-polig)
1 - Hostaansluitingen USB 3.1 USB Type Micro-B (10-polig, Gen 2, 10 Gbps)
Fysieke eigenschappen Gewicht product 74 g [2,6 oz]
Kleur Zwart
Type behuizing Kunststof
Max. schijfhoogte 0 mm [0,0 in]
Lengte product 13,2 cm [5,2 in]
Breedte product 88 mm [3,5 in]
Hoogte product 15 mm [0,6 in]
Gebruiksomgeving Bedrijfstemperatuur 0°C to 40°C (32°F to 104°F)
Opslagtemperatuur -10°C to 65°C (14°F to 149°F)
Vochtigheid Vochtigheid tijdens gebruik: 10% ~ 90% RV
Vochtigheid tijdens opslag: 5% ~ 95% RV
Hardware Interface USB 3.1 Gen 2
Bus type USB 3.1 Gen 2
Aantal stations 1
Schijfgrootte 2.5in
Schijftype SATA
Schijfinstallatie Vast
Ventilator(en) Nee
Chipsetcode ASMedia - ASM1351
Indicatoren 1 - LED-indicatoren Voeding & activiteit
Prestaties Maximale overdrachtsnelheid 10 Gbps
Type en snelheid USB 3.1 Gen 2 - 10 Gbit/s
UASP ondersteuning Ja
4Kn Support Ja
Type en snelheid SATA III (6 Gbps)
TRIM Support Ja
Max. schijfcapaciteit Momenteel getest met harde schijven tot 2 TB bij 7200 tpm
Software Besturingssystemen OS independent; No software or drivers required
Speciale opmerkingen / vereisten Notitie Windows 7 and earlier Windows versions do not support TRIM with USB to SATA devices.
Verpakkingsinformatie Package Height 44 mm [1,7 in]
Package Length 13,3 cm [5,2 in]
Verzendgewicht (verpakt) 195 g [6,9 oz]
Package Width 17,8 cm [7,0 in]
Voeding Inclusief voedingsadapter Gevoed via USB
Wat wordt er meegeleverd 1 - Meegeleverd USB 3.1 naar 2,5 inch SATA HDD-behuizing
USB 3.1 A naar micro B kabel - 58 cm
schijfbeschermend stootkussen
Verkorte handleiding

Accessoires

Niet meer leverbaar
PEXUSB312A

2 poorts USB 3.1 Gen 2 (10Gbps) PCI Express kaart - PCIe met 2x USB-A

Upgrade uw computer naar de snellere USB 3.1, door twee 10 Gbps USB Type-A poorten toe te voegen

Uw prijs
€32,99 EUR excl. VAT
€39,92 EUR incl. VAT
USB3AUB15CMS

Dunne micro USB 3.0-kabel - 15 cm

Minimaliseer kabelwarboel en plaats uw USB 3.0 Micro-apparaten gemakkelijk bij uw desktop of laptop met een dunne, flexibele kabel

Uw prijs
€7,99 EUR excl. VAT
€9,67 EUR incl. VAT
USB3SAUB1

30 cm SuperSpeed USB 3.0-kabel A naar Micro B

Sluit een USB 3.0 Micro USB externe harde schijf aan op uw computer

Uw prijs
€8,99 EUR excl. VAT
€10,88 EUR incl. VAT
USB3AUB50CMB

50 cm zwarte SuperSpeed USB 3.0-kabel A naar micro B - M/M

Sluit een USB 3.0 Micro USB externe harde schijf aan op uw computer

Uw prijs
€9,99 EUR excl. VAT
€12,09 EUR incl. VAT

Drivers/Downloads

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Firmware

Datasheet

Productondersteuning

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Veelgestelde vragen (FAQ)

Troubleshooting

When you troubleshoot issues with a hard drive enclosure, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Cables
  • Hard drives
  • Hard drive enclosure

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive enclosure in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive enclosure in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive enclosure, it is recommended that you do the following:

  • To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.​

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

If your setup components support USB 3.1 but you are experiencing slower transfer speeds than you expected, consider the following:

  • A USB host connection with multiple USB 3.1 ports might not be able to support 10Gbps on each port simultaneously.
  • The type of port on a device does not determine whether the device is capable of USB 3.1 speeds. A USB-C port might not support USB 3.1 speeds, while USB-A and USB-B ports might support USB 3.1 speeds.
  • Any other devices that you include in your setup, such as an older hard drive in a USB 3.1 enclosure, might create a point of congestion and slow down transfer speeds.

To confirm the functionality of your USB host connection, its ports, and any other devices in your setup, refer to the information provided by the manufacturer.

Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.

U zou de firmware van uw apparaat niet moeten upgraden als u geen problemen hebt met de functionaliteit van uw apparaat. De enige keer dat u een upgrade zou moeten overwegen, is wanneer u een probleem met het apparaat hebt en u hebt bevestigd dat de firmware dit probleem kan oplossen.  U kunt dit bevestigen door de bij de firmware geleverde documentatie te raadplegen of contact op te nemen met ons Technisch Ondersteuningsteam. Een verkeerde upgrade van de firmware kan leiden tot verminderde prestaties. U kunt dus het best contact opnemen met StarTech.com als u dit wilt uitvoeren.

Voor uw aanschaf

Hard drive enclosures require power from your system's USB port. Although you can plug in any standard SATA drive, USB ports only supply a limited amount of power and are not able to power all of the hard drives plugged into the system.

The power capabilities of the USB port combined with the power requirements of the attached hard drive will determine if the hard drive enclosure will work in your setup. The power (in mA) supplied by the USB port must be greater than the requirements of the hard drive.

A USB 2.0 port can supply a maximum of 500 mA (0.5 A), and a USB 3.0 port can supply a maximum of 900 mA (0.9 A).

You can usually find the power requirements of your hard drive in the technical specifications on the label of the hard drive or on the manufacturer's website.

Yes, this device supports the TRIM command. If the OS issues a TRIM command, the command will be passed to the connected device.

To determine if your hard drive will work in this enclosure, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the enclosure supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the enclosure was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the enclosure. For example, IDE, SATA, or M.2.
  • Make sure that the enclosure supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Make sure that the enclosure supports the height of your hard drive. For example, 9 mm or 15 mm.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the enclosure. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the enclosure.

USB 3.1 is the most recent version of the USB (Universal Serial Bus) standard for connecting computers and electronic devices. It is capable of data transfer speeds up to 10Gbps, and while it can use the USB-C connector type, it can also use a variety of other connector types. To achieve USB 3.1 transfer speeds, your USB host connection, cables, and device must all support USB 3.1. USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). 

USB 3.0 is capable of data transfer speeds up to 5Gbps. USB 3.0 is also known as USB 3.1 Gen 1 (5Gbps).

USB 3.1 is backwards compatible with USB 3.0 and USB 2.0, except in the following scenarios:

  • USB-B 3.1 cables are not compatible with USB-B 2.0 ports.
  • Unless you use an adapter, USB-C ports or cables will not work with USB-A or USB-B ports or cables.
  • Devices that require USB 3.1 transfer speeds of 10Gbps might not work with USB 3.0 or USB 2.0, or you might experience lower transfer speeds and impacted performance.
  • Bus-powered USB devices that requires more power than what USB 2.0 can provide are not compatible with USB 2.0.

To transfer data at speeds of 10Gbps, you need to confirm that the following components in your setup support USB 3.1:

  • The USB host connection
  • The USB cable
  • The USB device and any subcomponents (for example, a hard drive docking station and the hard drives in the docking station)

Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.

The included USB cable for this USB 3.1 Gen 2 device has been tested and verified to perform at USB 3.1 Gen 2 speeds of 10Gbps.

Hard Drives

Windows 10 

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).

Initialize a drive

Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.

  1. Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.

  2. Navigate to Disk Management.

  3. When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.

  4. Click OK.

Create a partition in a drive

Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.

  1. Right-click Unallocated or RAW volume, and select New Simple Volume.

  2. In the New Partition Wizard, click Next.

  3. Select Primary partition.

  4. Leave the partition size set to default, and click Next.

  5. Assign a drive letter or leave it set to the default, and click Next.

  6. Enter the following settings to format the partition:

  • In the File System field, enter NTFS.
  • Set the Allocation unit size to Default.
  • In the Volume label field, enter <your name/reference>.
  • Select the Perform a quick format check box.
  • Clear the Enable file and folder compression check box.
  1. Click Next > Finish.

The new drive should appear in Windows Explorer.

Mac OS

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).

Initialize a drive

Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.

Create a partition on a drive

Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.

To create a partition on a new drive, complete the following:

  1. Open Finder.

  2. Navigate to Applications and click Utilities.

  3. Open Disk Utility.

  4. Select the new drive and click the Partition tab.

  5. Click Options and verify that it is set to GUID Partition Table.

  6. Enter a name for the partition.

  7. Click Partition.

The drive should now be accessible in Finder.

 

Compliance and safety

Compliance letters

  • WEEE
    • Taal: English
  • RoHS
    • Taal: English

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Uitvoering en specificaties van het product zijn zonder aankondiging vatbaar voor wijzigingen.
Terug naar boven