Productcode: S322SAT3R
Met de S322SAT3R in de interne schijf gemonteerde SATA RAID-adapter kunt u twee SATA harde schijven aansluiten op één SATA-connector op uw moederbord, en zo een hardware RAID array bouwen.
Deze veelzijdige RAID-adapter heeft een ingebouwde hardware RAID-controller die JBOD, BIG, RAID 0, en RAID 1 ondersteunt, voor meer schijfcapaciteit, veilige dataredundantie of verbeterde systeem prestaties.
Met de twee bijgevoegde SATA-kabels hebt u alles dat u nodig heeft voor een probleemloze installatie. Deze plug & play HDD-adapter is gemakkelijk te installeren en wordt direct op uw schijf gemonteerd zonder extra bevestigingsmaterialen of software-installatie.
Om de prestatie te maximaliseren en de volledige snelheid van uw SATA III harde schijven te benutten, ondersteunt deze HDD RAID-controller SATA III voor datatransmissiesnelheden tot 6 Gbps in combinatie met een geschikte controller.
De S322SAT3R wordt gedekt door een 2-jarige garantie en gratis levenslange technische ondersteuning van StarTech.com.
Warranty Information | Warranty | 2 Years |
---|---|---|
Poorten | 2 | |
Connector(en) | 2 - Schijfaansluitingen | SATA (7-polig, data) |
1 - Hostaansluitingen | SATA data & voeding combinatie (7+15-polig) | |
Fysieke eigenschappen | Lengte product | 75,0 mm [3,0 in] |
Breedte product | 26,0 mm [1,0 in] | |
Hoogte product | 23,0 mm [0,9 in] | |
Gewicht product | 11,8 g [0,4 oz] | |
Gebruiksomgeving | Bedrijfstemperatuur | 5°C - 50°C (41°C to 122°C) |
Opslagtemperatuur | -25°C - 70°C (-13°C to 158°C) | |
Vochtigheid | Actief 20% tot 80% Niet-actief 15% tot 90% |
|
Hardware | Interface | SATA |
Aantal stations | 2 | |
Schijftype | SATA | |
Schijfinstallatie | Vast | |
Chipsetcode | JMicron - JMS562 | |
Prestaties | Maximale overdrachtsnelheid | 6 Gbit/s |
Type en snelheid | SATA III (6 Gbps) | |
Port-multiplier | Ja | |
RAID | Ja | |
Ondersteunde RAID-niveaus | BIG (span of lineair) | |
Max. schijfcapaciteit | Momenteel getest tot 4 TB 7200 RPM harde schijven | |
Hot-swappable | Nee | |
Ondersteunde RAID-niveaus | JBOD - (Just a Bunch of Disks) | |
RAID 0 (stripe) | ||
RAID 1 (mirror) | ||
Algemene specificaties | Voor de JBOD-modus moet uw SATA-controller Port Multiplier ondersteunen | |
Software | Besturingssystemen | OS independent; No software or drivers required |
Verpakkingsinformatie | Package Length | 17,3 cm [6,8 in] |
Package Width | 14,3 cm [5,6 in] | |
Package Height | 30,0 mm [1,2 in] | |
Verzendgewicht (verpakt) | 120,0 g [4,2 oz] | |
Wat wordt er meegeleverd | 1 - Meegeleverd | interne schijf gemonteerde, RAID-adapter - 2 SATA harde schijven |
2 - Meegeleverd | SATA-kabel (50 cm) | |
1 - Meegeleverd | LP4-naar-SATA-voedingsadapter | |
Handleiding |
Voeg twee SATA 6 Gbit/s-poorten toe voor high-speed toegang tot omvangrijke interne opslagmedia
Voeg 4 interne SATA III (6 Gbps)-poorten toe aan een computer met een PCI Express x2-sleuf
Voeg 2 externe SATA-poorten (eSATA) en 4 interne SATA-poorten toe aan uw desktopcomputer via een PCI Express uitbreidingsslot
Voeg 2 interne SATA 2.0 poorten toe aan uw desktopcomputer via een PCI Express uitbreidingsslot
Voeg een interne SATA-poort en een externe SATA-poort (eSATA) toe aan uw desktopcomputer via een PCI Express uitbreidingsslot
Voeg 2 externe of interne SATA-poorten van 6 Gbit/s toe aan een computer via een PCI Express-slot
Monteer een 3,5 inch harde schijf in een desktopcomputer met een beschikbare 5,25 inch bay
Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)In order to rebuild a RAID array, you need to replace a physical drive with an identical drive on the same RAID controller. Although standard RAID levels are generally agreed upon throughout the industry, the implementation varies between manufacturers. RAID arrays are typically not accessible when they are moved to another controller, and data may be unrecoverable if the drives are out of order or have been formatted or accessed by another RAID controller.
If a RAID controller has failed, you should get the exact same model of RAID controller.
Note: If a drive or drives were damaged, it is possible that the RAID array may be permanently unrecoverable.
RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, you should back up the data on another physical drive or logical set of drives.
With the following RAID modes, recovery is possible using the same StarTech.com product. Refer to the following table for the appropriate method to use to recover your RAID array.
RAID mode | Max # of failed drives | Procedure |
RAID 1 | Only one drive is needed for recovery. |
The array will rebuild and is accessible during the rebuilding process. |
RAID 3 | Single drive failure will rebuild. |
Note: Do not change the order of the drives.
|
RAID 5 | Single drive failure will rebuild. |
Note: Do not change the order of the drives.
|
RAID 10 | Only one drive in a mirrored set can fail. |
Note: Do not change the order of the drives.
|
Note: Not all StarTech.com devices support each of the RAID modes described below. For more information on the RAID modes that your device supports, refer to the manual or the StarTech.com product page.
Redundant Array of Independent Disks (RAID) is a virtual disk technology that combines multiple physical drives into one unit. RAID can create redundancy, improve performance, or do both.
RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, it should be backed up to another physical drive or logical set of drives.
The following are terms that are normally used in connection with RAID:
Different RAID levels exist for different application requirements.
Refer to the following table for the list of RAID modes offered by some StarTech.com products:
RAID mode | Description | Operation | Advantages | Disadvantages | Recovery |
RAID 0 | Striped disks | Data is split evenly between two or more disks. | Large size and the fastest speed. | No redundancy. | If one or more drives fails, this results in array failure. |
RAID 1 | Mirrored disks | Two or more drives have identical data on them. | A single drive failure will not result in data loss. | Speed and size is limited by the slowest and smallest disk. | Only one drive is needed for recovery. |
RAID 3 | Striped set with dedicated parity | Data is split evenly between two or more disks, plus a dedicated drive for parity storage. | High speeds for sequential read/write operations. | Poor performance for multiple simultaneous instructions. | A single drive failure will rebuild. |
RAID 5 | Striped disks with distributed parity | Data is split evenly between three or more disks. Parity is split between disks. | Large size, fast speed, and redundancy. | The total array size is reduced by parity. | A single drive failure will rebuild. |
RAID 10 | 1+0; Striped set of Mirrored Subset | Four or more drives are made into two mirrors that are striped. | Larger size and higher speed than RAID-1, and more redundancy than RAID-0. | No parity. | Only one drive in a mirrored set can fail. |
JBOD | Just a Bunch Of Disks | Any number of drives are accessed independently by the operating system. | Software RAID modes can be used. | Hardware RAID may have better performance. | N/A |
Big | Spanning or Concatenation | Data is written on one drive until it is full, and then the next drive(s) until it or they are full. | Creates a very large and simple array. |
No redundancy. |
N/A |
Clone | RAID 1 + Spare |
Two drives have identical data, plus one drive is used for rebuilding in case of a primary array failure. |
Seamless operation when one drive fails in a RAID-1 array. | Spare drive is not accessible to the user. | Only one drive is needed for recovery. |