Productcode: SATDOCK5U3ER
Met de SATDOCK5U3ER harde-schijfduplicator & docking station kunt u een 2,5 inch of 3,5 inch SATA harde schijf (HDD) of solid-state drive (SSD) tegelijkertijd klonen naar vijf andere SATA-schijven, als een standalone apparaat. Met de duplicator kunt u ook max. 5 schijven wissen, zonder een hostverbinding.
U kunt de duplicator ook gebruiken als een 5-bay HDD / SSD docking station, door deze via USB 3.0 of eSATA op een hostcomputersysteem aan te sluiten. Door ondersteuning van schijven met hoge capaciteit (getest tot 6 TB) is dit een eenvoudige en voordelige manier om de dataopslag-/back-upcapaciteit van uw computer aanzienlijk te vergroten.
Door data tegelijkertijd van een schijf naar vijf schijven te kopiëren, verhoogt de harde-schijfkloner uw productiviteit doordat u bij omvangrijke duplicatieprojecten geen schijven meer constant hoeft te plaatsen en te verwijderen.
Bovendien kan het dock tegelijkertijd max. vijf schijven wissen in meerdere bedieningsmodi, inclusief Snel wissen en Multipass Overwriting (DoD) -- de ideale oplossing voor het permanent wissen van vertrouwelijke informatie en ter bescherming van uw bedrijf en uw klanten tegen identiteitsdiefstal.
Dankzij het geïntegreerde LCD-scherm kunt u met de SATDOCK5U3ER de duplicatievoortgang gemakkelijk in de gaten houden en de kopieer-/wisresultaten en schijfdiagnoses bekijken tijdens standalone gebruik.
De behuizing is ook specifiek ontworpen voor gebruiksgemak. De schijfsleuven hebben een dubbel profiel voor het probleemloos wisselen van 2,5 inch en 3,5 inch harde schijven en solid-state drives zonder dat extra beugels of adapters nodig zijn.
Omdat het docking station via eSATA of USB 3.0 kan worden aangesloten, is de SATDOCK5U3ER een veelzijdige oplossing voor de uitbreiding van de opslagcapaciteit van bijna elke laptop of desktop. Voor snelle prestaties kunt u het docking station via eSATA op uw computer aansluiten voor efficiënte datatransmissiesnelheden tot 3 Gbps. Voor een bredere systeemcompatibiliteit kunt u het dock via USB 3.0 aansluiten, met neerwaartse compatibiliteit met USB 2.0/1.1 hostverbindingen.
De SATDOCK5U3ER heeft ook twee alleen-laden snellaad-USB-poorten, waardoor uw iPhone®, iPad®, en Android™ tablets of smartphones altijd volledig geladen zijn.
U kunt ook andere typen schijven dupliceren, wissen of openen in duplicatie- en snelwis toepassingen met behulp van een schijfadapter. De StarTech.com adapters in de onderstaande lijst zijn getest en zijn dus gegarandeerd compatibel met deze schijfduplicator:
2,5/3,5 inch IDE schijven - SAT2IDEADP
mSATA schijven - SAT2MSAT25
M.2 (NGFF) schijven - SAT32M225
Gebouwd voor betrouwbare, langdurige prestaties is de SATDOCK5U3ER gemaakt van duurzame materialen en wordt gedekt door een 2-jarige garantie en gratis levenslange technische ondersteuning van StarTech.com.
Warranty Information | Warranty | 2 Years |
---|---|---|
Connector(en) | 6 - Schijfaansluitingen | SATA data & voeding combinatie (7+15-polig) |
1 - Hostaansluitingen | eSATA (7-polig, data) | |
USB Type-B (9-polig) USB 3.0 | ||
Fysieke eigenschappen | Type behuizing | Staal |
Lengte product | 31,5 cm [12,4 in] | |
Breedte product | 15,2 cm [6,0 in] | |
Hoogte product | 75 mm [3,0 in] | |
Gewicht product | 1,5 kg [3,3 lb] | |
Gebruiksomgeving | Bedrijfstemperatuur | 5°C to 35°C (41°F to 95°F) |
Opslagtemperatuur | -20°C to 50°C (-4°F to 122°F) | |
Vochtigheid | 20%~80% RV | |
Hardware | Aantal stations | 5 |
Schijfgrootte | 2.5in & 3.5in | |
Schijftype | SATA | |
2 - Ventilatoren | 60 mm | |
Chipsetcode | SunplusIT - SPIF260A ASMedia - ASM1153 JMicron - JMB393 |
|
Indicatoren | 1 - LED-indicatoren | Vermogen docking station |
Bronschijf voeding en activiteit | ||
5 - LED-indicatoren | Doelschijf voeding / activiteit | |
Prestaties | Maximale overdrachtsnelheid | 5 Gbit/s |
Type en snelheid | USB 3.0 - 5 Gbit/s | |
SATA II (3 Gbps) | ||
Port-multiplier | Ja | |
Duplication Modes | Sector by Sector (Whole Drive) | |
Duplication Speed | 7GBpm | |
Wismodi | Quick Erase | |
Max. schijfcapaciteit | Momenteel getest tot 6 TB 7200 RPM | |
Wismodi | 1-Pass Overwrite (NIST SP 800-88 Rev 1 - Clear) | |
3-Pass Overwrite | ||
7-Pass Overwrite | ||
Algemene specificaties | 7 GB per minuut duplicatiesnelheid | |
Software | Besturingssystemen | OS independent; No software or drivers required |
Verpakkingsinformatie | Package Height | 19,7 cm [7,8 in] |
Package Length | 38,7 cm [15,2 in] | |
Verzendgewicht (verpakt) | 2,5 kg [5,5 lb] | |
Package Width | 27,6 cm [10,9 in] | |
Voeding | Inclusief voedingsadapter | Inclusief wisselstroomadapter |
Ingangsspanning | 100 - 240 AC | |
Ingangsstroom | 2 A | |
Uitgangsspanning | 19V DC | |
Uitgangsstroom | 5 A | |
Polariteit pin midden | Positief | |
Stekkertype | M | |
Vermogensopname | 95 | |
Wat wordt er meegeleverd | 1 - Meegeleverd | USB 3.0\eSATA 1:5 SATA HDD duplicatordock |
USB 3.0-kabel | ||
eSATA-kabel | ||
4 - Meegeleverd | Rubberen poten (geïnstalleerd) | |
1 - Meegeleverd | universele voedingsadapter (NA, GB, EU, ANZ) | |
Handleiding |
Gebruik uw 2,5 of 3,5 inch IDE harde schijven in een SATA docking station
Biedt bescherming tegen schokken en stoten aan een 2,5 inch harde schijf
Biedt bescherming tegen schokken en stoten aan een 3,5 inch harde schijf
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Sluit uw externe apparaten aan en zet gegevens over 10x sneller dan met USB 2.0
Sluit uw externe SATA-opslagapparaten aan op uw laptop of desktopcomputer.
Sluit uw externe SATA-opslagapparaten aan op uw laptop of desktopcomputer.
Voeg 2 eSATA-poorten voor inbouw toe aan een laptop via een ExpressCard/54-slot
Plaats een USB 3.0-adapter vlak in de ExpressCard-slot van een laptop
Voeg een smalle eSATA-inbouwpoort toe aan een laptop via ExpressCard
Voeg 2 USB 3.0-poorten toe aan uw desktopcomputer via een PCI Express uitbreidingsslot
Voeg twee USB 3.0 poorten toe aan uw laptop via een ExpressCard-sleuf
Voeg een eSATA-poort toe aan een computer via een PCI Express-slot
Maakt snelle toegang mogelijk tot een eSATA-apparaat via een USB 3.0-poort
Verander een M.2 SSD in een 7 mm hoge 2,5 inch SATA 6 Gbps Open Frame SSD
Verander een mSATA SSD in een 7 mm hoge 2,5 inch SATA 6 Gbps Open Frame SSD
Zet vrijwel elke 2,5 inch SATA of SAS harde schijf om in een 3,5 inch SATA-schijf
Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
To test your setup components, try the following:
When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:
Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.
This docking station allows the hard drive to enforce its own power state, as opposed to enforcing a power state that keeps the hard drive active at all times. Since most newer hard drives have low-power energy conservation modes, this will cause the hard drive to enter an idle state if it is not used for a certain amount of time.
You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.
The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.
Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.
Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.
After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:
The primary partition on the drive now uses the entire drive area.
StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode . A duplication that fails or halts will not cause a problem with the source drive.
You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.
StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.
If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.
Solid-state drives (SSDs) use SATA connectors to access power and transfer data. Any duplicator that can copy to or from SATA hard drives will work with a StarTech.com duplicator.
Note: If you use a dock to duplicate SSDs, keep in mind that the StarTech.com disk duplicators execute a sector by sector read and write. SSDs are rated by a number of reads and writes. Repeated duplication and sector by sector reads and writes of SSDs can reduce the life cycle of the drive.
Software-level encryption on the drive poses no issue to StarTech.com duplicators, as the duplicators copy encrypted data sector by sector over to the new drive.
Hardware-level encryption or BIOS level hard drive locks cause the duplication to halt and fail, as the drive is unable to read or write the sectors that are encrypted.
Duplication of Hidden Protected Area (HPA) Partitions or Extended Industry Standard Architecture (EISA) cause the duplicator to halt and fail, as the drive cannot read and write the protected partitions on the drive.
Note: Our UNIDUPDOCK, SATDOCK22RE and SATDOCK4U3RE do include the ability to copy HPA partitions, but the duplication is still dependent on how the HPA partition is written to the hard drive, whether or not it is encrypted and how it is encrypted.
StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.
SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.
To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).
Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.
Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.
Navigate to Disk Management.
When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.
Click OK.
Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.
Right-click Unallocated or RAW volume, and select New Simple Volume.
In the New Partition Wizard, click Next.
Select Primary partition.
Leave the partition size set to default, and click Next.
Assign a drive letter or leave it set to the default, and click Next.
Enter the following settings to format the partition:
The new drive should appear in Windows Explorer.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).
Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.
Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.
To create a partition on a new drive, complete the following:
Open Finder.
Navigate to Applications and click Utilities.
Open Disk Utility.
Select the new drive and click the Partition tab.
Click Options and verify that it is set to GUID Partition Table.
Enter a name for the partition.
Click Partition.
The drive should now be accessible in Finder.