Productcode: SATERASER4
Met deze harde-schijf wisser kunnen standalone tegelijkertijd tot vier 2,5 of 3,5 inch SATA harde schijven of solid-state drives worden gewist.
In tegenstelling tot hard-drive docking stations of adapters die een computerverbinding en software nodig hebben om schijven te wissen, kan deze hard-drivewisser standalone schijven wissen zonder dat een hostcomputer noodzakelijk is. Dit voorkomt de problemen veroorzaakt door aansluiting van uw schijven op een hostcomputer en beschermt uw schijven tegen externe bedreigingen op uw beveiliging zoals datatoegang op afstand.
Het 4-bay design biedt maximale efficiency door meerdere schijven te combineren tot aparte wisprojecten, zodat u waardevolle tijd bespaart. De harde-schijf wisser ondersteunt USB 3.0, ook bekend als USB 3.1 Gen 1, met bestandoverdrachtsnelheden tot 5 Gbps.
Met door de bedrijfstak erkende wismodi wist de harde-schijf wisser de data van uw 2,5 of 3,5 inch SSD of HDD. Deze schijf-wisser ondersteunt negen wismodi waaronder Quick Erase, Single en Multi-pass Overwrites, Custom Erase, NIST 800-88 Rev. 1 Purge comform Secure Erase en Enhanced Secure Erase. De Multi-pass Overwrite (3-Pass Full Disk Overwrite) wisprocedures voldoen aan de normen van het Amerikaanse Ministerie van Defensie (Dod) (5220.22-M).
Ondersteunt diverse wismodi waardoor de schijfwisser de perfecte oplossing is voor bijna elke professionele applicatie. Single-Pass Overwrite is ideaal voor IT-technici en systeembeheerders die oude harde schijven voor andere doeleinden willen gebruiken, terwijl Quick en Secure Erase, Single Pass Overwrite en Multi-pass Overwrite (die aan de eisen van het Amerikaanse Ministerie van Defensie voldoen) ideale oplossingen zijn voor onderzoekslaboratoria, zorginstellingen, advocatenkantoren en accountants die met gevoelige data omgaan en een veilige wismethode nodig hebben om mogelijke schendingen van de privacy te voorkomen.
Naast ondersteuning van 2,5/3,5 inch SATA SSD's en HDD's is de harde-schijf wisser ook geschikt voor 2,5 en 3,5 inch IDE harde schijven, mSATA schijven en SATA M.2 schijven met een compatibele StarTech.com adapter:
IDE harde schijven: Gebruik StarTech.com adapter SAT2IDEADP SATA naar 2,5 of 3,5 inch IDE harde-schijfadapter voor HDD docks
mSATA schijven: Gebruik StarTech.com adapter SAT32MSAT257 mSATA SSD naar 2,5 inch SATA-adapterconverter
M.2 schijven: Gebruik StarTech.com adapter SAT32M225 M.2 NGFF SSD naar 2,5 in SATA-adapterconverter
De harde-schijf wisser heeft handige menunavigatieknoppen voor gegarandeerd snelle en efficiënte prestaties en een geïntegreerd LCD-scherm dat de wismodi en taakstatus duidelijk aangeeft. U kunt de wisser ook aansluiten op een computer voor snelle toegang tot de schijf die op poort-1 is aangesloten.
Om te zorgen dat u kunt controleren welke bestanden zijn gewist, is de harde-schijf wisser voorzien van een 9-polige seriële poort die u op een seriële printer kunt aansluiten om direct wislogbestanden af te drukken.
De SATERASER4 wordt gedekt door een 2-jarige garantie en gratis levenslange technische ondersteuning van StarTech.com.
Warranty Information | Warranty | 2 Years |
---|---|---|
Connector(en) | 4 - Schijfaansluitingen | SATA data & voeding combinatie (7+15-polig) |
1 - Hostaansluitingen | USB Type-B (9-polig) USB 3.0 | |
1 - Andere aansluiting(en) | DB 9-pin Serial | |
Fysieke eigenschappen | Kleur | Zwart |
Type behuizing | Staal | |
Lengte product | 20,9 cm [8,2 in] | |
Breedte product | 96 mm [3,8 in] | |
Hoogte product | 30 mm [1,2 in] | |
Gewicht product | 712 g [25,1 oz] | |
Gebruiksomgeving | Bedrijfstemperatuur | 5°C ~ 45°C (41°F ~ 113°F) |
Opslagtemperatuur | -20°C ~85°C (-4°F ~ 185°F) | |
Vochtigheid | 20% ~ 80%, niet-condenserend | |
Hardware | Interface | USB 3.0 |
Bus type | USB 3.0 | |
Aantal stations | 4 | |
Schijfgrootte | 2.5in & 3.5in | |
Schijftype | SATA | |
Indicatoren | 1 - LED-indicatoren | 2-regel LCD-scherm aan de bovenkant |
4 - LED-indicatoren | Power-LED | |
Activiteit-LED | ||
HPA/DCO Detect LED | ||
Prestaties | Maximale overdrachtsnelheid | 3 Gbit/s |
Type en snelheid | USB 3.0 - 5 Gbit/s | |
SATA II (3 Gbps) | ||
Wismodi | Quick Erase | |
Max. schijfcapaciteit | Momenteel getest tot 10 TB 7200 RPM | |
Wismodi | 1-Pass Overwrite (NIST SP 800-88 Rev 1 - Clear) | |
Hot-swappable | Ja | |
Wismodi | 3-Pass Overwrite | |
7-Pass Overwrite | ||
Custom Erase | ||
Secure Erase (NIST SP 800-88 Rev 1 - Purge) | ||
Enhanced Secure Erase (NIST SP 800-88 Rev 1 - Purge) | ||
Software | Besturingssystemen | OS independent; No software or drivers required |
Speciale opmerkingen / vereisten | Notitie | Als u deze adapter op uw computer aansluit, is alleen de op poort-1 aangesloten harde schijf toegankelijk |
Voor het afdrukken van kassabonnen via de RS232 seriële poort is een printer nodig die de ESC/P printer controle taal ondersteunt. | ||
Verpakkingsinformatie | Verzendgewicht (verpakt) | 2,6 kg [5,8 lb] |
Package Length | 45 cm [17,7 in] | |
Package Width | 23,1 cm [9,1 in] | |
Package Height | 85 mm [3,3 in] | |
Voeding | Inclusief voedingsadapter | Inclusief wisselstroomadapter |
Ingangsspanning | 100 - 240 AC | |
Ingangsstroom | 1.2 A | |
Uitgangsspanning | 12V DC | |
Uitgangsstroom | 7 A | |
Polariteit pin midden | Positief | |
Stekkertype | M | |
Vermogensopname | 84 W | |
Wat wordt er meegeleverd | 1 - Meegeleverd | harde-schijf wisser |
universele voedingsadapter (NA/JP, EU, VK, ANZ) | ||
4 - Meegeleverd | drive pads | |
schijf-kabels | ||
1 - Meegeleverd | USB 3.0-kabel | |
verkorte handleiding |
Verander een M.2 SSD in een 7 mm hoge 2,5 inch SATA 6 Gbps Open Frame SSD
Verander een mSATA SSD in een 7 mm hoge 2,5 inch SATA 6 Gbps Open Frame SSD
Sluit uw externe apparaten aan en zet gegevens over 10x sneller dan met USB 2.0
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Biedt bescherming tegen schokken en stoten aan een 2,5 inch harde schijf
Maak van een mSATA mini-SSD een standaard 2,5 inch SATA SSD
Zet vrijwel elke 2,5 inch SATA of SAS harde schijf om in een 3,5 inch SATA-schijf
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Biedt bescherming tegen schokken en stoten aan een 3,5 inch harde schijf
Gebruik uw 2,5 of 3,5 inch IDE harde schijven in een SATA docking station
Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
To test your setup components, try the following:
When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:
Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.
This docking station allows the hard drive to enforce its own power state, as opposed to enforcing a power state that keeps the hard drive active at all times. Since most newer hard drives have low-power energy conservation modes, this will cause the hard drive to enter an idle state if it is not used for a certain amount of time.
You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.
The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.
Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.
Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.
After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:
The primary partition on the drive now uses the entire drive area.
StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode . A duplication that fails or halts will not cause a problem with the source drive.
You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.
StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.
If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.
Solid-state drives (SSDs) use SATA connectors to access power and transfer data. Any duplicator that can copy to or from SATA hard drives will work with a StarTech.com duplicator.
Note: If you use a dock to duplicate SSDs, keep in mind that the StarTech.com disk duplicators execute a sector by sector read and write. SSDs are rated by a number of reads and writes. Repeated duplication and sector by sector reads and writes of SSDs can reduce the life cycle of the drive.
Software-level encryption on the drive poses no issue to StarTech.com duplicators, as the duplicators copy encrypted data sector by sector over to the new drive.
Hardware-level encryption or BIOS level hard drive locks cause the duplication to halt and fail, as the drive is unable to read or write the sectors that are encrypted.
Duplication of Hidden Protected Area (HPA) Partitions or Extended Industry Standard Architecture (EISA) cause the duplicator to halt and fail, as the drive cannot read and write the protected partitions on the drive.
Note: Our UNIDUPDOCK, SATDOCK22RE and SATDOCK4U3RE do include the ability to copy HPA partitions, but the duplication is still dependent on how the HPA partition is written to the hard drive, whether or not it is encrypted and how it is encrypted.
StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.
SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.
Quick and secure erase functions
Quick erase and secure erase are functions the duplicators call on the hard drives themselves. How they work depends on the manufacturer of the hard drive.
Department of Defense erase function
A Department of Defense (DoD) erase is a function performed by the duplicator where it does three passes. The first pass writes all 0s. The second pass writes all 1s. The third pass writes 0s and 1s randomly.
Note: Not all duplicators will feature all of these erase modes. It is important to review the product manual to confirm the available erase modes.
To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).
Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.
Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.
Navigate to Disk Management.
When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.
Click OK.
Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.
Right-click Unallocated or RAW volume, and select New Simple Volume.
In the New Partition Wizard, click Next.
Select Primary partition.
Leave the partition size set to default, and click Next.
Assign a drive letter or leave it set to the default, and click Next.
Enter the following settings to format the partition:
The new drive should appear in Windows Explorer.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).
Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.
Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.
To create a partition on a new drive, complete the following:
Open Finder.
Navigate to Applications and click Utilities.
Open Disk Utility.
Select the new drive and click the Partition tab.
Click Options and verify that it is set to GUID Partition Table.
Enter a name for the partition.
Click Partition.
The drive should now be accessible in Finder.