Productcode: SDOCK2U33V
Met dit dual-bay SATA HDD/SSD docking station kunt u tegelijkertijd schijven docken en swappen vanaf uw desktop of laptop, met één USB-poort. Het ondersteunt twee 2,5/3,5 inch SATA harde schijven of solid-state drives.
Het dual-bay docking station ondersteunt USB 3.0, ook bekend als USB 3.1 Gen 1, en biedt snelle dataoverdracht tot 5 Gbps. Bovendien ondersteunt het UASP voor nog betere prestaties.
Ideaal voor IT-professionals zoals systeembeheerder en technici, kunt u met dit hard drive dock onderhoudstaken efficiënter uitvoeren, zoals dupliceren van schijfbeelden, dataherstel, back-up en archivering van harde schijven en overdracht van content tussen schijven en apparaten. Het verbetert ook uw werkstroom omdat u snel toegang hebt tot uw harde schijven en schijven, indien nodig, eenvoudig kunt swappen.
Ontworpen voor gemakkelijk schijftoegang, verbetert het dock ook uw werkstroom omdat u snel toegang hebt tot twee harde schijven en schijven, indien nodig, eenvoudig kunt swappen. Het hard drive dock heeft een comfortabel toplader design met aparte schijfkleppen waardoor u schijven gemakkelijk kunt toevoegen of verwijderen.
Het dual-bay SATA HDD/SSD docking station is onafhankelijk van het besturingssysteem, en u hoeft geen stuurprogramma's of software te installeren.
De SDOCK2U33V wordt gedekt door een 2-jarige garantie en gratis levenslange technische ondersteuning van StarTech.com.
Warranty Information | Warranty | 2 Years |
---|---|---|
Connector(en) | 2 - Schijfaansluitingen | SATA data & voeding combinatie (7+15-polig) |
1 - Hostaansluitingen | USB 3.1 USB Type-B (9 pin, Gen 1, 5 Gbps) | |
Fysieke eigenschappen | Kleur | Zwart |
Type behuizing | Aluminium en kunststof | |
Lengte product | 11,4 cm [4,5 in] | |
Breedte product | 13,0 cm [5,1 in] | |
Hoogte product | 62,0 mm [2,4 in] | |
Gewicht product | 370,0 g [13,1 oz] | |
Gebruiksomgeving | Bedrijfstemperatuur | 5°C to 35°C (41°F to 95°F) |
Opslagtemperatuur | -20°C to 50°C (-4°F to 122°F) | |
Vochtigheid | 20%RV~80%RV | |
Hardware | Ventilator(en) | Nee |
Interface | USB 3.0 | |
Bus type | USB 3.0 | |
Aantal stations | 2 | |
Schijfgrootte | 2.5in & 3.5in | |
Schijftype | SATA | |
Schijfinstallatie | Verwijderbaar | |
Chipsetcode | ASMedia - ASM1153E | |
Indicatoren | 2 - LED-indicatoren | drive activiteits-LED |
1 - LED-indicatoren | Power-LED | |
Prestaties | Type en snelheid | USB 3.0 - 5 Gbit/s |
UASP ondersteuning | Ja | |
TRIM Support | Ja | |
4Kn Support | Ja | |
S.M.A.R.T. Support | Ja | |
Type en snelheid | SATA III (6 Gbps) | |
Port-multiplier | Nee | |
RAID | Nee | |
Max. schijfcapaciteit | Momenteel getest met harde schijven tot 10 TB bij 7200 rpm | |
Software | Besturingssystemen | OS independent; No software or drivers required |
Speciale opmerkingen / vereisten | Notitie | Windows 7 and earlier Windows versions do not support TRIM with USB to SATA devices. |
Verpakkingsinformatie | Verzendgewicht (verpakt) | 782,0 g [27,6 oz] |
Package Length | 13,5 cm [5,3 in] | |
Package Width | 12,5 cm [4,9 in] | |
Package Height | 12,0 cm [4,7 in] | |
Voeding | Inclusief voedingsadapter | Inclusief wisselstroomadapter |
Ingangsspanning | 100 - 240 AC | |
Ingangsstroom | 1.5 A | |
Uitgangsspanning | 12V DC | |
Uitgangsstroom | 3 A | |
Polariteit pin midden | Positief | |
Stekkertype | M | |
Vermogensopname | 36 | |
Wat wordt er meegeleverd | 1 - Meegeleverd | drive docking station |
1,2m USB 3.0-kabel | ||
universele voedingsadapter (N-A/JP, VK, EU, ANZ) | ||
verkorte handleiding |
Gebruik uw 2,5 of 3,5 inch IDE harde schijven in een SATA docking station
Biedt bescherming tegen schokken en stoten aan een 2,5 inch harde schijf
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Voeg 2 USB 3.0-poorten toe aan uw desktopcomputer via een PCI Express uitbreidingsslot
Voeg één interne en één externe SuperSpeed USB 3.0-aansluiting toe aan uw PC
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Biedt bescherming tegen schokken en stoten aan een 3,5 inch harde schijf
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Sluit uw externe apparaten aan en zet gegevens over 10x sneller dan met USB 2.0
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Zorgt voor een veilige omgang met en antistatische bescherming voor de meeste 2,5 inch harde schijven
Voeg 4 externe USB 3.0-poorten toe aan een low-profile of standaard computer via PCI Express
Voeg via een PCI-Express-sleuf 4 onafhankelijke SuperSpeed USB 3.0-poorten aan uw PC toe
Voeg twee USB 3.0 poorten toe via een mini PCI Express-sleuf
Voeg twee USB 3.0-poorten toe aan uw desktopcomputer via een PCI Express-slot
Voeg 2 USB 3.0-poorten toe via een Mini ExpressCard-slot
Voeg 4 USB 3.0-poorten toe aan uw desktopcomputer via een PCI Express uitbreidingsslot
Vervang uw zoekgeraakte of defecte voedingsadapter
Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size
If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.
When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.
There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.
When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
To test your setup components, try the following:
When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:
Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.
This docking station allows the hard drive to enforce its own power state, as opposed to enforcing a power state that keeps the hard drive active at all times. Since most newer hard drives have low-power energy conservation modes, this will cause the hard drive to enter an idle state if it is not used for a certain amount of time.
To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).
Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.
Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.
Navigate to Disk Management.
When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.
Click OK.
Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.
Right-click Unallocated or RAW volume, and select New Simple Volume.
In the New Partition Wizard, click Next.
Select Primary partition.
Leave the partition size set to default, and click Next.
Assign a drive letter or leave it set to the default, and click Next.
Enter the following settings to format the partition:
The new drive should appear in Windows Explorer.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).
Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.
Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.
To create a partition on a new drive, complete the following:
Open Finder.
Navigate to Applications and click Utilities.
Open Disk Utility.
Select the new drive and click the Partition tab.
Click Options and verify that it is set to GUID Partition Table.
Enter a name for the partition.
Click Partition.
The drive should now be accessible in Finder.