1 poorts 10G Ethernet Netwerkkaart - PCI Express - Intel X550-AT Chip

Prior to installing this device, ensure that your operating system is up to date (for example, you have installed the most recent service pack).

To install the driver:

1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Support). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Users\your_name\Downloads).

2. Once the download is complete, right-click the zip folder that you downloaded, select Extract All, and follow the on-screen instructions.
3. Open the appropriate folder for your operating system.
4. Right-click on either Windows 32bit.exe or Windows 64bit.exe as appropriate for your operating system. 
5. Click Run as Administrator.

Note: If the Run as Administrator option is not available, you might be attempting to run the installer from within the zipped file. Extract the files using the instructions in Step 2.

6. Follow the on-screen prompts to install the device drivers and restart the computer when prompted.
7. Your computer will automatically complete the driver installation and your device should be ready to use.

When you troubleshoot issues with a network adapter, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

• Ethernet cables
• Network devices
• Computer system

To test your setup components, try the following:

• Use the Ethernet cables, network devices, and computer system in another setup to see if the problem is with the components or the setup.
• Use different Ethernet cables, network devices, and a different computer system in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

• Test each cable individually.
• Use short cables when you are testing.

When you test the Ethernet cables, network devices, and computer system, it is recommended that you do the following:

• In Device Manager, check under Network Adapters. To open Device Manager, press the Windows key + R, type devmgmt.msc, and press Enter.
• If you are using a USB network adapter and you do not see the network adapter listed in Device Manager, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=expansion-cards#usb-cannot-detect-windows.
• If you are using a PCI/PCIe network adapter and you do not see the network adapter listed in Device Manager, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=expansion-cards#pci-pcie-cannot-boot-os-or-detect-windows.
• If you are using a CardBus/ExpressCard adapter and you do not see the network adapter listed in Device Manager, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=expansion-cards#cb-ec-cannot-detect-windows.
• If the device is listed with an error, follow the instructions on the product page to reinstall the drivers.
• Check to see if your network devices (for example, a network switch, router, and so on) use compatible protocols (for example, 10/100, Gigabit, and so on).
• Make sure that the link LEDs on the adapter are illuminated when it is plugged into a network device. If the link LEDs are illuminated, it means that a good electrical connection exists between the devices.
• If you use a wall jack with an Ethernet cable, make sure that the jack is patched in properly.

Sometimes an on-board network interface card (NIC) conflicts with a new NIC.  In these cases it is best to disable the on-board NIC.

The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible.  To do this, consult your motherboard manual.

You can also disable any NIC in Windows.  Here is how you do this:

First click Start, or, in Windows 10 and 8, hold down the Windows key and press X.  Then click Control Panel.

Windows 10

1. Click Network and Internet.
2. Click Network and Sharing Center.
3. On the left, click Change adapter settings.
4. Right-click the NIC that you would like to disable and select Disable.

Windows 8

1. Click Network and Sharing Center.
2. On the left, click Change adapter settings.
3. Right-click the NIC that you would like to disable and select Disable.

Windows 7

1. Click Network and Internet.
2. Click Network and Sharing Center.
3. On the left, click Change adapter settings.
4. Right-click the NIC that you would like to disable and select Disable.

Windows Vista

1. Click Network and Sharing Center.
2. On the left, click Manage network connections.
3. Right-click the NIC that you would like to disable and select Disable.

Windows XP

1. Click Network Connections.
2. Right-click the NIC that you would like to disable and select Disable.

If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings.  You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

Note: You must log in as the local administrator before you continue.

To open Device Manager:

• Press Windows key + R.
• Type devmgmt.msc.
• Click OK.

1. Open the Networking adapters section.
2. Right-click the network adapter that you want to change and select Properties.
3. Click the Advanced tab.
4. Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate. Select any of the speeds that you see in the list.
5. Click OK and restart your computer.

To confirm that Windows detects your expansion card, complete the following:

1. Press the Windows key+R, type devmgmt.msc, and press Enter.
2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.