Niet meer leverbaar

2-poort Low-Profile Gigabit Ethernet Netwerkkaart

Voeg twee Gigabit Ethernet-poorten toe aan een computer, server of werkstation via een PCI Express-slot

Productcode: ST1000SPEXD2

  • Twee RJ-45 Ethernet-poorten met 10/100/1000 Mbit/s
  • Ondersteuning voor Jumbo Frames
  • On-chip buffer van 48 kB voor zenden/ontvangen
De ST1000SPEXD2 2-poort PCI-E Gigabit Ethernet Netwerkkaart (Low-Profile) biedt twee 10/100/1000 Mbit/s Ethernet-poorten en is volledig compatibel met de IEEE 802.3/u/ab-normen. De netwerkkaart is geschikt voor elke computer, server of werkstation met PCI Express en ondersteunt high-performance dual-channel netwerkverkeer en maximale overdrachtsnelheden van 1000Mbit/s in elke richting (totaal 2000 Mbit/s) - tot 10 keer sneller dan met 10/100 Ethernet. Deze low-profile netwerkkaart ondersteunt functies als Jumbo Frames, VLAN-tagging en Wake-on-LAN (WOL), en wordt geleverd met een optionele standaard bracket, zodat de kaart gemakkelijk is te installeren in een low-profile (kleine vormfactor) of standaard computerbehuizing of server.

Toepassingen

  • Voeg 2 Ethernet-poorten toe aan een werkstation of server in een enkele PCIe-slot
  • Leg een verbinding met 2 verschillende netwerken tegelijk
  • Installeer dubbele netwerkcapaciteit in een computersysteem met kleine vormfactor of beperkte ruimte

Het voordeel van StarTech.com

  • Voeg 2 Gigabit Ethernet-poorten toe in een enkele PCI-E-slot van een standaard of low-profile computersysteem met kleine vormfactor (SFF)
  • Ondersteunt geavanceerde functies zoals Jumbo Frames en VLAN-tagging, evenals Wake-On-LAN en Auto-MDIX
  • Met 2 jaar garantie en gratis levenslange technische ondersteuning door StarTech.com

Partnernummers

  • UPC 065030845403

Compatibility

  • Windows 8 logo
  • Windows 7 logo
  • Windows Server 2012 logo
  • Mac OS X Mavericks (10.9) logo
  • Linux logo
Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista(32/64), XP(32/64), CE 5.0/4.2, 2000, ME, 98SE
Windows Server® 2012, 2008 R2, 2003(32/64)
Mac OS® 10.4 and up (Intel-based - Tested up to 10.9)
Linux Kernel 2.4.x and up
SCO OpenServer 5.0.7/ 6

Specificaties

Warranty Information Warranty 2 Years
Connector(en) 2 - Externe poorten RJ-45
Fysieke eigenschappen Lengte product 11 cm [4,3 in]
Breedte product 74 mm [2,9 in]
Gewicht product 200 g [7,1 oz]
Gebruiksomgeving Bedrijfstemperatuur 0°C to 55°C (32°F to 131°F)
Opslagtemperatuur -20°C to 75°C (-4°F to 167°F)
Vochtigheid 10% - 90% rel. luchtvochtigheid (niet-condenserend)
Hardware Poorten 2
Interface RJ45 (gigabit Ethernet)
Bus type PCI Express
Kaarttype Low Profile (incl. standaard bracket)
Industriestandaarden IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Chipsetcode Realtek - RTL8111C
Indicatoren 2 - LED-indicatoren LED's voor verbinding en activiteit
Prestaties Maximale overdrachtsnelheid 1000 Mbit/s (unidirectioneel), 2000 Mbit/s (bidirectioneel)
Buffergrootte 48 KB
Compatibele netwerken 10/100/1000 Mbps
Auto MDIX Ja
Full duplex ondersteuning Ja
Software Besturingssystemen Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista(32/64), XP(32/64), CE 5.0/4.2, 2000, ME, 98SE
Windows Server® 2012, 2008 R2, 2003(32/64)
Mac OS® 10.4 and up (Intel-based - Tested up to 10.9)
Linux Kernel 2.4.x and up
SCO OpenServer 5.0.7/ 6
Verpakkingsinformatie Package Length 22 cm [8,7 in]
Package Width 15 cm [5,9 in]
Package Height 40 mm [1,6 in]
Verzendgewicht (verpakt) 250 g [8,8 oz]
Wat wordt er meegeleverd 1 - Meegeleverd PCi Express netwerkadapter
Standaard montagebracket
Driver-CD
Handleiding

Drivers/Downloads

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Drivers:

Firmware

Handleiding:

Datasheet

Productondersteuning

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Veelgestelde vragen (FAQ)

Installatie

Prior to installing this device, ensure that your operating system is up to date (for example, you have installed the most recent service pack).

To install the driver:

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Support). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Documents and Settings\your_name\My Documents\Downloads).

  1. Once the download is complete, right-click the zip folder that you downloaded, select Extract All, and follow the on-screen instructions.
  2. Select the appropriate folder for your operating system.
  3. Double-click Setup.exe.
  4. Follow the on-screen prompts to install the device drivers and restart the computer when prompted.
  5. Your computer will automatically complete the driver installation and your device should be ready to use.

Troubleshooting

When you troubleshoot issues with a network adapter, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Ethernet cables
  • Network devices
  • Computer system

To test your setup components, try the following:

  • Use the Ethernet cables, network devices, and computer system in another setup to see if the problem is with the components or the setup.
  • Use different Ethernet cables, network devices, and a different computer system in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.
  • Use short cables when you are testing.

When you test the Ethernet cables, network devices, and computer system, it is recommended that you do the following:

Sometimes an on-board network interface card (NIC) conflicts with a new NIC.  In these cases it is best to disable the on-board NIC.

The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible.  To do this, consult your motherboard manual.

You can also disable any NIC in Windows.  Here is how you do this:

First click Start, or, in Windows 10 and 8, hold down the Windows key and press X.  Then click Control Panel.

Windows 10

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows 8

  1. Click Network and Sharing Center.
  2. On the left, click Change adapter settings.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows 7

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows Vista

  1. Click Network and Sharing Center.
  2. On the left, click Manage network connections.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows XP

  1. Click Network Connections.
  2. Right-click the NIC that you would like to disable and select Disable.

If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings.  You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

Note: You must log in as the local administrator before you continue.

To open Device Manager:

  • Press Windows key + R.
  • Type devmgmt.msc.
  • Click OK.
  1. Open the Networking adapters section.
  2. Right-click the network adapter that you want to change and select Properties.
  3. Click the Advanced tab.
  4. Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate. Select any of the speeds that you see in the list.
  5. Click OK and restart your computer.

U zou de firmware van uw apparaat niet moeten upgraden als u geen problemen hebt met de functionaliteit van uw apparaat. De enige keer dat u een upgrade zou moeten overwegen, is wanneer u een probleem met het apparaat hebt en u hebt bevestigd dat de firmware dit probleem kan oplossen.  U kunt dit bevestigen door de bij de firmware geleverde documentatie te raadplegen of contact op te nemen met ons Technisch Ondersteuningsteam. Een verkeerde upgrade van de firmware kan leiden tot verminderde prestaties. U kunt dus het best contact opnemen met StarTech.com als u dit wilt uitvoeren.

Hoe gaat u te werk

StarTech.com does not support a Preboot Execution Environment (PXE) as this requires third-party software. However, our devices can be used as long as the following conditions are met:

  1. The BIOS must support PXE.
  2. The BIOS must see the card.
  3. The environment must have drivers for the chipset used in the card.
  4. If using a USB networking card, the environment must have support for USB devices as well.

The drivers on our website include a Realtek Diagnostic Toolkit that you can use to easily set up a VLAN tag.

Make sure that you are logged in as the local administrator before continuing.

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Downloads). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Users\your_name\Downloads).

  1. Once the download is complete, right-click the Realtek_PCI_GbE.zip file or the Realtek_PCIe_GbE.zip file.
  2. Select Extract All and note the location that the files will be extracted to.
  3. Select Extract. The extracted files will open automatically.
  4. In the list of extracted files, do one of the following:
  • If you are running Windows Vista/7/8, right-click the Setup.exe file and select Run as Administrator.
  • If you are running Windows XP, double-click the Setup.exe file.
  1. Follow the on-screen instructions to install the software.
  2. Open the software and under the VLAN settings, you can add, delete, or modify the VID (VLAN ID).

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Uitvoering en specificaties van het product zijn zonder aankondiging vatbaar voor wijzigingen.
Terug naar boven
Wacht...