1-poort PCI 10/100 Mbit/s Ethernet Netwerkkaart Adapter

Voeg een 10/100 Mbit/s Ethernetpoort toe aan een desktopcomputer via een PCI-slot

Productcode: ST100S

  • Enkele 10/100 Mbit/s RJ45 Ethernet-poort
  • Voldoet aan de IEEE802.3 CSMA/CD, 802.3 10Base-T en 100Base-TX specificaties
  • Full en half duplex-ondersteuning
Uw prijs
€10,99 EUR excl. VAT
€13,30 EUR incl. VAT

Deze 1-poort PCI Fast Ethernet Netwerk-adapterkaart biedt een betrouwbare, kosteneffectieve Ethernet-netwerkverbinding. De netwerkkaart legt een eenvoudige verbinding met 10/100 Mbit/s Ethernet-netwerken, beschikt over een automatische regeling die de snelheid en duplex-functionaliteit van aangesloten apparaten detecteert en biedt full-duplex ondersteuning voor overdrachtsnelheden tot 200 Mbit/s.

De netwerkkaart biedt een veelzijdig oplossing voor het leggen van een netwerkverbinding, wordt ondersteund door alle populaire besturingssystemen, waaronder Windows, Linux, Mac OS en Novell, en wordt geleverd met levenslange garantie door StarTech.com.

Toepassingen

  • Vervanging voor de Ethernet-kaart in een desktopcomputer thuis of op kantoor
  • Voeg Ethernet-netwerkconnectiviteit toe voor breedband-internettoegang op een oudere desktopcomputer
  • Voeg een tweede of reserve-netwerkaansluiting toe aan een werkstation of server

Het voordeel van StarTech.com

  • Kosteneffectieve en eenvoudige Ethernet-netwerkconnectiviteit voor desktopcomputersystemen
  • Met levenslange garantie en gratis technische ondersteuning door StarTech.com

Partnernummers

  • Ingram Micro Belgium 1585087
  • D&D Distribution ST100SCN
  • Tech Data - Belgium 4462013
  • UPC 065030780155

Compatibility

  • Windows 8 logo
  • Linux logo
  • Windows 7 logo
  • Windows 10 logo
  • Windows Server 2016 logo
  • Windows Server 2019 logo
Windows® NT, 98SE, 2000, XP, Vista, 7, 8, 8.1, 10
Windows Server® 2008 R2, 2012, 2016, 2019
Mac OS® 10.0.4, 9.1 / 9.0
Unix, Linux 2.6 tot 4.11.x Alleen LTS-versies
NetWare 3.x/4.x

Specificaties

Warranty Information Warranty Lifetime
Connector(en) 1 - Type connector(en) PCI / PCI-X (universeel 3,3 & 5 V, 32-bits)
1 - Externe poorten RJ-45
Fysieke eigenschappen Gewicht product 40,0 g [1,4 oz]
Lengte product 12,0 cm [4,7 in]
Breedte product 32,0 mm [1,3 in]
Hoogte product 12,0 cm [4,7 in]
Gebruiksomgeving Bedrijfstemperatuur 0°C to 55°C (32°F to 131°F)
Vochtigheid 10-90% rel. luchtvochtigheid, niet-condenserend
Hardware Poorten 1
Interface RJ45 (10/100 Ethernet)
Bus type PCI / PCI-X (5 / 3.3V)
Kaarttype Standaard bracket (incl. low profile bracket)
Industriestandaarden IEEE 802.3/802.3u
Chipsetcode Realtek - RTL8100C
Indicatoren 1 - LED-indicatoren Netwerkverbinding/-activiteit
10/100 Mbit/s selectie
Prestaties Maximale overdrachtsnelheid 200 Mbit/s
Compatibele netwerken 10/100 Mbps
Full duplex ondersteuning Ja
Software Besturingssystemen Windows® NT, 98SE, 2000, XP, Vista, 7, 8, 8.1, 10
Windows Server® 2008 R2, 2012, 2016, 2019
Mac OS® 10.0.4, 9.1 / 9.0
Unix, Linux 2.6 tot 4.11.x Alleen LTS-versies
NetWare 3.x/4.x
Speciale opmerkingen / vereisten Notitie IRQ en I/O-adres toegewezen door systeem
Verpakkingsinformatie Package Height 29,0 mm [1,1 in]
Package Length 14,3 cm [5,6 in]
Verzendgewicht (verpakt) 133,0 g [4,7 oz]
Package Width 17,0 cm [6,7 in]
Voeding Vermogensopname ≤1.5W
Wat wordt er meegeleverd 1 - Meegeleverd PCI Ethernet Kaart
Low-profile bracket
Driver-CD
Handleiding

Drivers/Downloads

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Productondersteuning

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Veelgestelde vragen (FAQ)

Installatie

Prior to installing this device, ensure that your operating system is up to date (for example, you have installed the most recent service pack).

To install the driver:

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Support). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Users\your_name\Downloads).

  1. Once the download is complete, right-click the zip folder that you downloaded, select Extract All, and follow the on-screen instructions.
  2. Select the appropriate folder for your operating system.
  3. Right-click Setup.exe. 
  4. Click Run as Administrator.

Note: If the Run as Administrator option is not available, you might be attempting to run the installer from within the zipped file. Extract the files using the instructions in Step 2.

  1. Follow the on-screen prompts to install the device drivers and restart the computer when prompted.
  2. Your computer will automatically complete the driver installation and your device should be ready to use.

Prior to installing this device, ensure that your operating system is up to date (for example, you have installed the most recent service pack).

To install the driver:

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Support). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Documents and Settings\your_name\My Documents\Downloads).

  1. Once the download is complete, right-click the zip folder that you downloaded, select Extract All, and follow the on-screen instructions.
  2. Select the appropriate folder for your operating system.
  3. Double-click Setup.exe.
  4. Follow the on-screen prompts to install the device drivers and restart the computer when prompted.
  5. Your computer will automatically complete the driver installation and your device should be ready to use.

Troubleshooting

When you troubleshoot issues with a network adapter, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Ethernet cables
  • Network devices
  • Computer system

To test your setup components, try the following:

  • Use the Ethernet cables, network devices, and computer system in another setup to see if the problem is with the components or the setup.
  • Use different Ethernet cables, network devices, and a different computer system in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.
  • Use short cables when you are testing.

When you test the Ethernet cables, network devices, and computer system, it is recommended that you do the following:

Sometimes an on-board network interface card (NIC) conflicts with a new NIC.  In these cases it is best to disable the on-board NIC.

The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible.  To do this, consult your motherboard manual.

You can also disable any NIC in Windows.  Here is how you do this:

First click Start, or, in Windows 10 and 8, hold down the Windows key and press X.  Then click Control Panel.

Windows 10

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows 8

  1. Click Network and Sharing Center.
  2. On the left, click Change adapter settings.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows 7

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows Vista

  1. Click Network and Sharing Center.
  2. On the left, click Manage network connections.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows XP

  1. Click Network Connections.
  2. Right-click the NIC that you would like to disable and select Disable.

If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings.  You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

Note: You must log in as the local administrator before you continue.

To open Device Manager:

  • Press Windows key + R.
  • Type devmgmt.msc.
  • Click OK.
  1. Open the Networking adapters section.
  2. Right-click the network adapter that you want to change and select Properties.
  3. Click the Advanced tab.
  4. Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate. Select any of the speeds that you see in the list.
  5. Click OK and restart your computer.

Hoe gaat u te werk

StarTech.com does not support a Preboot Execution Environment (PXE) as this requires third-party software. However, our devices can be used as long as the following conditions are met:

  1. The BIOS must support PXE.
  2. The BIOS must see the card.
  3. The environment must have drivers for the chipset used in the card.
  4. If using a USB networking card, the environment must have support for USB devices as well.

To confirm that Windows detects your expansion card, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

To confirm that the Mac OS detects your expansion card, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your expansion card is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Voor uw aanschaf

Yes. This PCI card uses a universal connector keyed for both 3.3V and 5V that can be used with PCI and PCI-X. This type of connector is identified as having 2 separate notches, instead of just one.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Uitvoering en specificaties van het product zijn zonder aankondiging vatbaar voor wijzigingen.
Terug naar boven
Wacht...