3 poorts USB C naar USB-A hub met Gigabit Ethernet - USB-C naar 3x USB-A - USB 3.0 - Inclusief voedingsadapter

Sometimes an on-board network interface card (NIC) conflicts with a new NIC.  In these cases it is best to disable the on-board NIC.

The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible.  To do this, consult your motherboard manual.

You can also disable any NIC in Windows.  Here is how you do this:

First click Start, or, in Windows 10 and 8, hold down the Windows key and press X.  Then click Control Panel.

Windows 10

1. Click Network and Internet.
2. Click Network and Sharing Center.
3. On the left, click Change adapter settings.
4. Right-click the NIC that you would like to disable and select Disable.

Windows 8

1. Click Network and Sharing Center.
2. On the left, click Change adapter settings.
3. Right-click the NIC that you would like to disable and select Disable.

Windows 7

1. Click Network and Internet.
2. Click Network and Sharing Center.
3. On the left, click Change adapter settings.
4. Right-click the NIC that you would like to disable and select Disable.

Windows Vista

1. Click Network and Sharing Center.
2. On the left, click Manage network connections.
3. Right-click the NIC that you would like to disable and select Disable.

Windows XP

1. Click Network Connections.
2. Right-click the NIC that you would like to disable and select Disable.

If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings.  You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

Note: You must log in as the local administrator before you continue.

To open Device Manager:

• Press Windows key + R.
• Type devmgmt.msc.
• Click OK.

1. Open the Networking adapters section.
2. Right-click the network adapter that you want to change and select Properties.
3. Click the Advanced tab.
4. Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate. Select any of the speeds that you see in the list.
5. Click OK and restart your computer.

If the USB device does not work after your computer has been in extended hibernation, it is likely that Windows has automatically turned off the USB Root hub to save power. 

The steps below outline how to configure the USB root hub to stay on during hibernation, to prevent this from happening.
 

Windows 10 / 8

1. On your keyboard, press the Windows key + X and select Control Panel.
2. Click Hardware and Sound, then click Power Options.
3. Click Change plan settings for the plan you want to change.
4. Click Change advanced power settings.
5. Click the plus sign (+) next to “USB settings” and “USB selective suspend setting” to expand the options and change the setting to Disabled.
6. Click OK to apply the setting.

Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.

Windows 7 / Vista

1. Click the Start button and select Control Panel.
2. Click Hardware and Sound, then click Power Options.
3. Click Change plan settings for the plan you want to change.
4. Click Change advanced power settings.
5. Click the plus sign (+) next to “USB settings” and “USB selective suspend setting” to expand the options and change the setting to Disabled.
6. Click OK to apply the setting.

Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.

Windows XP

1. On your desktop, right-click the My Computer icon and select Properties.
2. Click the Device Manager tab.
3. Expand Universal Serial Bus controllers by clicking the arrow to the left of it.
4. Right-click the first USB Root Hub device and select Properties.
5. Click the Power Management tab.
6. Clear the box next to Allow the computer to turn off this device to save power.
7. Click OK to apply the setting.
8. Repeat steps 4-7 for any remaining devices in the Universal Serial Bus Controllers section with “Root Hub” in the name.

Note: You may need to disconnect and re-connect your USB device after applying these settings to re-establish the connection.

StarTech.com does not support a Preboot Execution Environment (PXE) as this requires third-party software. However, our devices can be used as long as the following conditions are met:

1. The BIOS must support PXE.
2. The BIOS must see the card.
3. The environment must have drivers for the chipset used in the card.
4. If using a USB networking card, the environment must have support for USB devices as well.

It is possible to use some USB hubs without a power supply, however, doing so may prevent certain high-power USB peripherals from operating.

When a power adapter is not used on a hub that comes with a power adapter, power is drawn from the USB port on the computer and then divided between the ports on the hub. This reduces the power delivery to individual ports and high-powered USB peripherals, such as external hard drives, may not start.

On USB hubs that can use a power adapter, more power can be supplied to USB ports than what is possible with a single USB port.

If your USB peripherals require power adapters, they probably do not require power from the USB port and can be used on a USB hub without a power adapter. With USB peripherals that use power adapters, the USB ports on the hub are only used for data transfer and do not draw power from the hub.

USB peripherals that require low power (for example, keyboards and mice) can be used on hubs without a power adapter, in conjunction with other low-power USB peripherals. In this case, power is drawn from the computer's USB port, as described above.

USB-C is a type of USB connector that is capable of supporting the following:

• Data transfer speeds up to 10Gbps, if you use USB 3.1.
• Bi-directional power delivery up to 100W, if both the USB host connection and the device support it.
• Alternate modes, which deliver different types of data at different speeds. For example, DisplayPort Alternate Mode (DP Alt Mode).

If using Thunderbolt 3 over USB-C, the connection is capable of additional features. For example, Thunderbolt 3 is capable of 40Gbps of total bandwidth. For more information, refer to the following FAQ: https://www.startech.com/faq/thunderbolt-3-port-capabilities.

Not all USB-C ports or devices are capable of supporting all of the features listed above, or all of the features at the maximum capabilities. If you require a specific USB-C feature, your USB host connection, cables, and device must all support the feature that you require. For more information about whether your components support specific USB-C features, refer to the information provided by the manufacturers.