StarTech.com's ISA-based RS232 Serial Card (16550 UART) can be installed in an ISA motherboard slot to add an RS232 serial COM port, with support for data transfer rates of up to 460.8Kbps for peak serial device performance.
The ISA Serial Adapter Card includes drivers for Windows® 3.1, 95, 98, NT4 and NT5, and offers a full built-in jumper set to ensure easy configuration and broad compatibility.
A cost-effective solution for connecting serial modems, POS devices, PDAs, digital cameras, printers, ISDN terminal adapters and more, to a system, the ISA serial card is backed by StarTech.com's Lifetime Warranty and free lifetime technical support.
|Connector(en)||1 - Type connector(en)||ISA (16-bit)|
|1 - Externe poorten||DB-9 (9-polig, D-Sub)|
|Fysieke eigenschappen||Lengte product||12,8 cm [5,0 in]|
|Hoogte product||70 mm [2,8 in]|
|Gebruiksomgeving||Bedrijfstemperatuur||-10°C to 80°C (14°F to 176°F)|
|Opslagtemperatuur||-20°C to 100°C (-4°F to 212°F)|
|Poorttype||Geïntegreerd op kaart|
|Chipsetcode||National Semiconductor - NS16550AFN|
|Prestaties||Maximale overdrachtsnelheid||460.8 Kbps|
|Max. baudrate||460,8 kbit/s|
|Algemene specificaties||COM Settings: COM1 to COM7|
|Verpakkingsinformatie||Package Length||15 cm [5,9 in]|
|Package Width||22 mm [0,9 in]|
|Package Height||13,8 cm [5,4 in]|
|Verzendgewicht (verpakt)||120 g [4,2 oz]|
|Wat wordt er meegeleverd||1 - Meegeleverd||I/O CARD|
Verander een DB9 mannelijke poort in een DB25 mannelijke poort
Verandert een DB9 mannelijke poort in een DB25 vrouwelijke poort
When you troubleshoot issues with a serial device, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
To test your setup components, try the following:
Use the serial cable, serial port, and serial device in another setup to see if the problem is with the components or the setup.
Use a different serial cable, serial port, and serial device in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.
When you test your cables, it is recommended that you do the following:
Test each cable individually.
Use short cables when you are testing.
When you test the serial ports and serial device, it is recommended that you do the following:
Press the Windows key + R, type devmgmt.msc, and press Enter to open Device Manager. Check to see if your device is listed under Ports (COM & LPT).
Make sure that the COM port number is the correct number for the serial device and that the software being used to connect the computer to the serial device uses the correct COM port number.
If you do not see the COM port number in Device Manager see this FAQ for PCI/PCIe expansion cards: https://www.startech.com/support/faqs/technical-support?topic=expansion-cards#pci-pcie-cannot-boot-os-or-detect-windows
or this FAQ for USB devices: https://www.startech.com/support/faqs/technical-support?topic=expansion-cards#usb-cannot-detect-windows
If the device is listed with an error, follow the instructions on the website to reinstall the drivers.
Note: Some serial devices work only if the COM port number is between a certain range. For example, COM1 to COM4.
Perform a serial loopback test. See this FAQ on how to perform a RS-232 serial loopback test: http://www.startech.com/faq/serial_loopback_test_rs232_windows
To check whether or not an RS-232 serial port is working, perform an RS-232 loopback test by doing the following:
Note: To open a telnet session on the COM port, you need a telnet client like PuTTY or Hyper Terminal. Windows XP comes with Hyper Terminal.
If the loopback test fails, make sure that the serial cable or gender changer that you are using works and that the adapter is in the correct port.
You can check multiple ports at the same time by opening multiple sessions, putting the loopback adapter on one port, and trying to type into each session. When you can see what you are typing, you know that the COM port is working and you can see which port number the physical serial port is. Close the window for the port that you just tested to speed up the testing of the remaining serial ports.