Niet meer leverbaar

2-poort PCI naar IDE Controller/Adapter-kaart

Voeg twee interne IDE-aansluitingen toe aan uw computer via een PCI-slot

Productcode: PCIIDE2

  • Twee IDE-aansluiting met elk twee kanalen
  • Ondersteuning voor Ultra ATA/133 harde schijven met overdrachtsnelheden tot 133 MB/s
  • 48-bits LBA
Deze 2-poort IDE (Ultra ATA/133) Controller-kaart kan worden geïnstalleerd in een PCI-slot om meer IDE-opslagcapaciteit toe te voegen aan uw pc. Met twee IDE-kanalen, ondersteuning voor twee schijven per kanaal en overdrachtsnelheden tot 133 Mb/s kan deze adapterkaart worden gebruikt als primair boot-apparaat en ingebouwde IDE-poorten vervangen of 2 snelle poorten toevoegen aan het systeem. De adapter is ontworpen om te worden gebruikt met snelle IDE/133-drives maar ondersteunt ook harde schijven van 100 MB/s, 66 MB/s en 33 MB/s, cd-roms, cd-rw-drives en andere ATA-randapparatuur. Om voor een probleemloze installatie te zorgen, wordt de IDE-controller geleverd met Bus-Master drivers voor Windows 98/ME/NT 4/2000/XP en Vista™.


  • Vervang een defecte IDE-poort op het moederbord
  • Sluit oudere harde schijven, cd/dvd-drives, ZIP-drives, etc aan op een nieuwere computer

Het voordeel van

  • Twee IDE-aansluiting met elk twee kanalen biedt ondersteuning voor maximaal vier PATA-apparaten op één kaart
  • Met levenslange garantie en gratis technische ondersteuning door


  • Ingram Micro Belgium 1592813
  • UPC 065030824330


  • Windows 8 logo
  • Windows Server 2012 logo
  • Linux logo
  • Windows 7 logo
  • Windows 10 logo
  • Windows Server 2016 logo
  • Windows Server 2019 logo
Windows® 98SE, ME, 2000, XP, Vista, 7, 8, 8.1, 10
Windows Server® 2008 R2, 2012, 2016, 2019


Warranty Information Warranty Lifetime
Connector(en) 1 - Type connector(en) PCI / PCI-X (universeel 3,3 & 5 V, 32-bits)
2 - Interne poorten IDE (40-polig, EIDE/PATA)
Fysieke eigenschappen Lengte product 12,0 cm [4,7 in]
Breedte product 18,0 mm [0,7 in]
Hoogte product 85,0 mm [3,3 in]
Gewicht product 73,0 g [2,6 oz]
Hardware Poorten 2
Interface IDE
Bus type PCI / PCI-X (5 / 3.3V)
Kaarttype Standaard
Industriestandaarden ATA/ATAPI-6
Chipsetcode ITE - IT8212F
Prestaties Maximale overdrachtsnelheid 133 MB/s
LBA-ondersteuning 48-bit
Max. schijfcapaciteit Tot 132 GB
Software Besturingssystemen Windows® 98SE, ME, 2000, XP, Vista, 7, 8, 8.1, 10
Windows Server® 2008 R2, 2012, 2016, 2019
Verpakkingsinformatie Package Length 21,0 cm [8,3 in]
Package Width 39,0 mm [1,5 in]
Package Height 14,3 cm [5,6 in]
Verzendgewicht (verpakt) 220,0 g [7,8 oz]
Wat wordt er meegeleverd 1 - Meegeleverd PCI-kaart


Niet meer leverbaar

24in Round ATA 100/133 IDE Cable

Sluit twee harde schijven aan op een IDE-controller in een computer

Uw prijs
€7,98 EUR excl. VAT
€9,66 EUR incl. VAT
Niet meer leverbaar

18in Round Dual Drive Ultra ATA IDE Hard Drive Cable

Sluit twee harde schijven aan op een IDE-controller in een computer

Uw prijs
€7,99 EUR excl. VAT
€9,67 EUR incl. VAT
Niet meer leverbaar

18in Dual Drive Ultra ATA TPO IDE Hard Drive Cable

Sluit twee ATA-apparaten aan op een IDE-controller in een computer

Uw prijs
€4,99 EUR excl. VAT
€6,04 EUR incl. VAT


Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)





Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Veelgestelde vragen (FAQ)


Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ:

If you are unable to detect your IDE (PATA) drive using a product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.

When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.

There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.

When you troubleshoot issues with a hard drive controller card, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables

  • Hard drives

  • Hard drive controller card

To test your setup components, try the following:

  • Use the IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in another setup to see if the problem is with the components or the setup.

  • Use a different IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.

  • Use short cables when you are testing.

When you test the hard drive and hard drive controller card, it is recommended that you do the following:

  1. To open the Device Manager, press the Windows key + R, type devmgmt.msc, and press Enter. Check the IDE ATA/ATAPI controllers (for IDE) section, or the Storage controllers (for SATA) section.

  2. Do one of the following:

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.

  2. If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive does not show up in Computer or My Computer until it has a drive letter assigned to it.

Hoe gaat u te werk

To confirm that Windows detects your expansion card, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to and look on the Technical Specifications tab for your product.

No, this hard drive controller card does not support starting an operating system from a connected hard drive.

For a list of hard drive controller cards that support this feature and instructions on how to configure them, refer to the following FAQ:

Voor uw aanschaf

Note: For more information on how to detect an IDE hard drive, visit

Older IDE drives are not supported by current products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.

There are a number of reasons that older IDE drives may not be detected, including the following:

  • The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).

  • The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).

  • The sector size is not 512 bytes.

Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.

This device supports the ATA Packet Interface (ATAPI) protocol. ATAPI is required for optical drives, including CD-ROM drives, DVD-ROM drives, and Blu-ray players. Because this device supports ATAPI, optical drives are also supported.


Yes. This PCI card uses a universal connector keyed for both 3.3V and 5V that can be used with PCI and PCI-X. This type of connector is identified as having 2 separate notches, instead of just one.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Uitvoering en specificaties van het product zijn zonder aankondiging vatbaar voor wijzigingen.
Terug naar boven