Dual M.2 NGFF SATA Adapter with RAID
Install two M.2 SSDs into a 2.5” bay to create high-performance storage with configurable RAID
Product ID: 25S22M2NGFFR
Boost your system performance by enhancing the capacity, speed and security of your data storage. This two-drive M.2 to SATA adapter lets you install two M.2 solid-state drives in a single 2.5” drive bay and configure a powerful RAID array.
Build a RAID array to enhance system performance
The dual M.2 to SATA adapter supports multiple RAID modes (RAID 0, 1, BIG) helping you to achieve greater SSD capacity or data redundancy, depending on your selected RAID mode. The SSD adapter also supports non-RAID operation (JBOD) when paired with a port-multiplying SATA controller, so both drives can be used independent of one another.
Maximize file transfer speeds
The dual SSD adapter lets you utilize the full potential of your SATA III controller. Using M.2 SSDs in place of a platter drive reduces your data transfer bottlenecks and gives you file transfer speeds of up to 6 Gbps. M.2 SSDs also save you money by reducing your power consumption over regular platter drives.
The M.2 NGFF SATA RAID adapter also provides TRIM support to enhance the stability and performance of your M.2 NGFF SSDs.
Get dependable drive protection
The M.2 to SATA adapter features an enclosed housing that helps protect your NGFF (Next Generation Form Factor) SSD. The added protection gives you peace of mind when you are using your M.2 drives in applications that require an added level of durability such as hot-swap drive bays, or external SATA docking stations.
The 25S22M2NGFFR is backed by a StarTech.com 2-year warranty and free lifetime technical support.
- Add data redundancy to your system, by adding a mirrored SSD (RAID 1)
- Increase the storage capacity of your system by adding an additional SSD in a RAID array (RAID 0/BIG)
- Turn two unused M.2 drives into a regular 2.5in SATA solid-state drive
- Retrieve/backup data from an M.2 (NGFF) drive using a standard SATA computer
- Use M.2 drives in any 2.5 in. SATA application
Ingram Micro Singapore
|Chipset ID||ASMedia - ASM1092R|
|Compatible Drive Types||M.2 (SATA, B-Key, NGFF)|
|Drive Size||22m - M.2 NGFF|
|Number of Drives||2|
|Supported Drive Height(s)||2230|
|General Specifications||Not compatible with M.2 NVMe or AHCI PCI-Express SSDs
In order to see multiple drives in JBOD mode, your computer’s SATA controller must also support Port Multiplier.
|Maximum Data Transfer Rate||6Gbps|
|Supported RAID Modes||RAID 0 (Striped Disks)|
|RAID 1 (Mirrored Disks)|
|JBOD - (Just a Bunch of Disks)|
|BIG (Spanning or Concatenation)|
|Type and Rate||SATA III (6 Gbps)|
|Drive Connectors||1 - SATA Data & Power Combo (7+15 pin) Female|
|Host Connectors||2 - M.2 (SATA, B-Key, NGFF) Male|
|OS Compatibility||OS independent; No software or drivers required|
|LED Indicators||2 - Drive Error|
|Humidity||5% ~ 95% RH|
|Operating Temperature||0°C to 50°C (32°F to 122°F)|
|Storage Temperature||-10°C to 85°C (14°F to 185°F)|
|Color||Black & Silver|
|Material||Steel and Plastic|
|Product Height||0.3 in [8 mm]|
|Product Length||3.9 in [99 mm]|
|Product Width||2.8 in [70 mm]|
|Weight of Product||1.9 oz [55 g]|
|Package Height||1.2 in [31 mm]|
|Package Length||6.5 in [16.5 cm]|
|Package Width||5.2 in [13.1 cm]|
|Shipping (Package) Weight||4.2 oz [118 g]|
|What's in the Box|
|Included in Package||1 - dual M.2 NGFF SATA RAID adapter|
|2 - M.2 drive mount hardware|
|4 - screws|
|1 - mini screwdriver|
|1 - quick start guide|
Mount a 2.5in SATA hard drive to any computer with an available 3.5in bay
Mount two 2.5in SATA SSDs/HDDs into a single 3.5in drive bay
Frequently Asked Questions
Before You Buy
Although M.2 SSDs come in similar form factors, only an M.2 SATA drive with an NGFF B key will operate with this device. M.2 drives that are PCIe or have a different key position are not compatible with this device.
This device can adapt an M.2 SATA drive to standard SATA connections, which is not possible for a PCIe based M.2 drive. The key type refers to the connector type on the M.2 SATA drive. B key can be M.2 PCIe x2 or SATA, so it is important that you check the specifications of the drive to see if it supports SATA.
Note: Not all StarTech.com devices support each of the RAID modes described below. For more information on the RAID modes that your device supports, refer to the manual or the StarTech.com product page.
Redundant Array of Independent Disks (RAID) is a virtual disk technology that combines multiple physical drives into one unit. RAID can create redundancy, improve performance, or do both.
RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, it should be backed up to another physical drive or logical set of drives.
The following are terms that are normally used in connection with RAID:
- Striping: data is split between multiple disks.
- Mirroring: data is mirrored between multiple disks.
- Parity: also referred to as a checksum. Parity is a calculated value used to mathematically rebuild data.
Different RAID levels exist for different application requirements.
Refer to the following table for the list of RAID modes offered by some StarTech.com products:
|RAID 0||Striped disks||Data is split evenly between two or more disks.||Large size and the fastest speed.||No redundancy.||If one or more drives fails, this results in array failure.|
|RAID 1||Mirrored disks||Two or more drives have identical data on them.||A single drive failure will not result in data loss.||Speed and size is limited by the slowest and smallest disk.||Only one drive is needed for recovery.|
|RAID 3||Striped set with dedicated parity||Data is split evenly between two or more disks, plus a dedicated drive for parity storage.||High speeds for sequential read/write operations.||Poor performance for multiple simultaneous instructions.||A single drive failure will rebuild.|
|RAID 5||Striped disks with distributed parity||Data is split evenly between three or more disks. Parity is split between disks.||Large size, fast speed, and redundancy.||The total array size is reduced by parity.||A single drive failure will rebuild.|
|RAID 10||1+0; Striped set of Mirrored Subset||Four or more drives are made into two mirrors that are striped.||Larger size and higher speed than RAID-1, and more redundancy than RAID-0.||No parity.||Only one drive in a mirrored set can fail.|
|JBOD||Just a Bunch Of Disks||Any number of drives are accessed independently by the operating system.||Software RAID modes can be used.||Hardware RAID may have better performance.||N/A|
|Big||Spanning or Concatenation||Data is written on one drive until it is full, and then the next drive(s) until it or they are full.||Creates a very large and simple array.||
|Clone||RAID 1 + Spare||
Two drives have identical data, plus one drive is used for rebuilding in case of a primary array failure.
|Seamless operation when one drive fails in a RAID-1 array.||Spare drive is not accessible to the user.||Only one drive is needed for recovery.|
Compliance and Safety
- If product has an exposed circuit board, do not touch the product under power.
- If Class 1 Laser Product. Laser radiation is present when the system is open.
- Wiring terminations should not be made with the product and/or electric lines under power.
- Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
- Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Product appearance and specifications are subject to change without notice.