Product ID: SAT2IDEADP
The SAT2IDEADP SATA to IDE hard drive adapter enables you to use your 2.5-inch/3.5-inch IDE-based (PATA) hard drives in most StarTech.com SATA-based HDD Docking Stations. The SATA-IDE adapter features all-metal construction that ensures maximum durability, and is fully compatible with IDE hard drives up to ATA-133 (133MBps).
The unique mounting style of the SATA/IDE adapter enables it to be easily mounted to an IDE/ATA hard drive, and inserted into a SATA hard drive dock bay, for quick and easy retrieval of data from older HDDs. The adapter can also be used to install IDE hard drives into SATA-only desktop computers, or any other scenario that requires an IDE hard drive to be connected through Serial ATA.
The SAT2IDEADP hard drive adapter works with most StarTech.com SATA HDD Docking Stations and Duplicators.
Backed by 2-year warranty and free, lifetime technical support.
|Warranty Information||Warranty||2 Years|
|Connector(s)||1 - Connector Type(s)||SP4 (4 pin, Small Drive Power)|
|1 - Drive Connectors||LP4 (4 pin; Large Drive Power)|
|IDE (40 Pin, EIDE/PATA)|
|IDE (44 Pin, EIDE/PATA, 2.5" HDD)|
|1 - Host Connectors||SATA Power (15 pin)|
|SATA (7 pin, Data)|
|Environmental||Operating Temperature||5°C to 80°C (41°F to 176°F)|
|Storage Temperature||-40°C to 70°C (-40°F to 158°F)|
|Humidity||8% ~ 90% RH|
|Hardware||Number of Drives||1|
|Drive Size||2.5in & 3.5in|
|Compatible Drive Types||IDE (ATA)|
|Chipset ID||JMicron - JM20330|
|Packaging Information||Package Height||2.0 in [52 mm]|
|Package Length||5.8 in [14.7 cm]|
|Shipping (Package) Weight||7.7 oz [218 g]|
|Package Width||4.3 in [11 cm]|
|Performance||Hardware Raid Supported||No|
|Physical Characteristics||Weight of Product||3.7 oz [104 g]|
|Product Length||4.0 in [10.1 cm]|
|Product Width||3.1 in [78 mm]|
|Product Height||1.0 in [2.6 cm]|
|Software||OS Compatibility||OS independent; No software or drivers required|
|What's in the Box||1 - Included in Package||SATA to IDE adapter|
|40-pin IDE cable|
|40-pin to 44-pin IDE cable with power|
|SP4 to LP4 Power cable|
|Package of mounting screws|
Easily connect and swap two 2.5 or 3.5in SATA hard drives through eSATA or USB
Exactly duplicate one 2.5in or 3.5in SATA hard drive to another, effortlessly and without a computer
Desktop Front Bay Adapter
Enable quick access to four 2.5"/3.5" SATA HDD over USB 3.0 or eSATA
Enable fast, swappable access to your 2.5in or 3.5in SATA hard drives, through USB 3.0
Connect both an IDE and SATA hard drive to a computer through USB 2.0
Clone any combination of 2.5in or 3.5in IDE or SATA hard drives
Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size
If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.
When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.
There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.
Note: For more information on how to detect an IDE hard drive, visit http://www.startech.com/faq/hard_drive_accessories_ide_detection.
Older IDE drives are not supported by current StarTech.com products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.
There are a number of reasons that older IDE drives may not be detected, including the following:
The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).
The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).
The sector size is not 512 bytes.
Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.
Check out our review guidelines.