Product ID: SAT32M225
Vastly increase the performance of your system by adding the speed of an M.2 SATA SSD in any 2.5" SATA application, with this M.2 SATA SSD to 2.5in SATA adapter.
Utilize the full potential of your SATA III controller, with an M.2 SATA SSD, reducing your data transfer bottleneck with file transfer speeds up to 6Gbps. This M.2 SATA NGFF to SATA adapter can also save you money by reducing your power consumption over regular platter drives.
This M.2 SATA to 2.5 in. SATA adapter offers a fast an easy setup with no drivers to install. The mounting hardware is also included with the M.2 SATA SSD to SATA adapter for a quick installation.
The M.2 SATA SSD to 2.5 in. SATA converter helps protect the health of your drive with an open-frame design that maximizes heat dissipation.
SAT32M225 is backed by a StarTech.com 2-year warranty, and lifetime technical support.
|Warranty Information||Warranty||2 Years|
|Connector(s)||1 - Drive Connectors||M.2 (SATA, B-Key, NGFF)|
|1 - Host Connectors||SATA Data & Power Combo (7+15 pin)|
|Environmental||Operating Temperature||-40°C to 85°C (-40°F to 185°F)|
|Number of Drives||1|
|Compatible Drive Types||M.2 (SATA, B-Key, NGFF)|
|Supported Drive Height(s)||2230|
|Packaging Information||Package Height||1.3 in [32 mm]|
|Package Length||5.7 in [14.5 cm]|
|Shipping (Package) Weight||3.6 oz [102 g]|
|Package Width||6.9 in [17.5 cm]|
|Performance||Maximum Data Transfer Rate||6 Gbps|
|Type and Rate||SATA III (6 Gbps)|
|Hardware Raid Supported||No|
|Hot Swap Capability||No|
|General Specifications||Not compatible with M.2 NVMe or AHCI PCI-Express SSDs|
|Physical Characteristics||Weight of Product||1.3 oz [36 g]|
|Product Length||3.9 in [10 cm]|
|Product Width||2.8 in [70 mm]|
|Product Height||0.3 in [0.7 cm]|
|Software||OS Compatibility||OS independent; No software or drivers required|
|What's in the Box||1 - Included in Package||M.2 NGFF SSD to 2.5in SATA SSD Converter|
|Mounting screw kit|
Latching SATA connectors, for securely fastened hard drive installations.
Mount a 2.5in SATA hard drive to any computer with an available 3.5in bay
Mount two 2.5in SATA SSDs/HDDs into a single 3.5in drive bay
Connect an IDE hard drive to a Serial ATA power connector
To confirm that the Mac OS detects your USB device, complete the following:
You may need to refresh the System Information page after you plug in your device. To do so, press Command + R with the System Information page open.
Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.
Although M.2 SSDs come in similar form factors, only an M.2 SATA drive with an NGFF B key will operate with this device. M.2 drives that are PCIe or have a different key position are not compatible with this device.
This device can adapt an M.2 SATA drive to standard SATA connections, which is not possible for a PCIe based M.2 drive. The key type refers to the connector type on the M.2 SATA drive. B key can be M.2 PCIe x2 or SATA, so it is important that you check the specifications of the drive to see if it supports SATA.
Check out our review guidelines.