18in Dual Drive Ultra ATA IDE Hard Drive Cable

Product ID: IDE66

0 stars (0 reviews) |
Your price
€3,99 EUR excl. VAT
€4,99 EUR incl. VAT

This 18in dual drive IDE cable lets you connect two ATA 66/100/133 drives to a computer IDE port, as Master and Slave drives. This high quality flat ribbon-style IDE cable is the ideal solution for connecting hard disk drives, CD-ROMs, Tape Backup drives, Zip drives, DVD-ROM, or any ATA peripheral to your IDE capable computer.

The StarTech.com Advantage

  • Cost-effective solution for connecting two ATA 66/100/133 drives to a computer IDE port, as Master and Slave drives
  • Easy to use and install
  • Backed by StarTech.com's lifetime warranty

Partner Numbers

  • Ingram Micro Sweden V930029
  • UPC 065030783118

Specifications

Warranty Information Warranty Lifetime
Connector(s) Connector A 1 - IDE (40 Pin, EIDE/PATA)
Connector B 2 - IDE (40 Pin, EIDE/PATA)
Packaging Information Shipping (Package) Weight 0,0 kg [0,1 lb]
Package Length 12,3 cm [4,8 in]
Package Width 1,0 cm [0,4 in]
Package Height 20 mm [0,8 in]
Performance Maximum Cable Length 914
Physical Characteristics Weight of Product 49 g [1,7 oz]
Color Gray
Cable Length 457,2 mm [18,0 in]
Product Length 45,7 cm [18,0 in]
Special Notes / Requirements Note 12 and 6 inches between connectors
What's in the Box Included in Package 1 - 18 In. Dual Drive Ultra ATA 66/100/133 Cable

Drivers/Downloads

Talk to an Advisor

We are always ready to assist you with any questions you may have.

Live Chat (opens in new window)

Datasheet

Product Support

Talk to an Advisor

We are always ready to assist you with any questions you may have.

Live Chat (opens in new window)

Frequently Asked Questions

Troubleshooting

When you troubleshoot issues with an IDE cable, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Hard drive

  • Hard drive controller (for example, the motherboard)

  • IDE cable

To test your setup components, try the following:

  • Use the hard drive, hard drive controller, and IDE cable in another setup to see if the problem is with the components or the setup.

  • Use a different hard drive, hard drive controller, and IDE cable in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

IDE cables have three connectors that use the same 40-pin connector, but each connection has a specific assignment. One end plugs into the motherboard and the other two ends plug into the master drive (primary, required) and slave drive (secondary, optional). To identify the connections for your cable, refer to the following table:

Connection Location on cable Color (on some cables)
Master The end of the cable and close to the slave drive. Gray
Slave The middle of the cable. Black
Motherboard The end of the cable farthest away from the slave drive. Blue

The information in the above table applies to Cable select mode, which is a jumper pin configuration. Refer to the manual for your IDE hard drive for more information about how the jumpers should be set for the mode that you want to use.

Note: Do not "hotplug" the IDE cable. Always power down the hard drive and the hard drive controller before making any connection changes.

When you test your hard drive, hard drive controller and IDE cable, it is recommended that you do the following:

  • Complete your testing with only one drive attached to the cable in the master position.

  • Verify that the hard drive is spinning without the IDE cable attached. The power cable attached to the drive should make the drive spin.

  • Make sure that the cable is inserted into the drive in the correct orientation. On drives without a key or pin 19 missing, line up the red stripe on the cable with pin 1 on the hard drive.

  • If the hard drive is not being detected in the BIOS, make sure that the jumpers are set correctly on the hard drive.

  • If the hard drive is not being detected in your operating system, make sure that the drive is formatted with a partition (for example, NTFS or FAT32). If you are using a computer running a version of Windows, a drive letter must also be assigned to the hard disk drive.

For more information about how to initialize a drive, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#initialize-hard-drives.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
*Product appearance and specifications are subject to change without notice.

Customer Reviews

(0 reviews)
0 out of 5 stars
  • 5 (0)
  • 4 (0)
  • 3 (0)
  • 2 (0)
  • 1 (0)
Tell us what you think of this product.
Need a little help getting started?

Check out our review guidelines.

Feedback Back to top