Product ID: CPNTUTPWALLA
This component video and audio extender wall plate kit includes both transmitter and receiver units, allowing you to make out-of-the-way connections from a component video source to a remote display / HDTV. The transmitter and receiver wall plates can be placed in a wall or ceiling gang for a cleaner, more professional A/V installation, supporting connection distances up to a maximum of 100m (300ft).
Run a 480i/480p signal up to 100m or a 720p/1080i signal up to 50m. The CPNTUTPWALLA is a passive extender meaning no power adapter is required. Simply run a Cat 5e cable from the transmitter to the receiver, and install the wall-plates.
Offering maximum versatility and convenience, the component wall plate kit is easy to install; simply wall-mount the transmitter unit near the intended video source, then wall-mount the receiver unit near the display, projector, or HDTV. The transmitter and receiver units can then be linked using standard Cat5e cable, providing a high quality video extension while concealing the cable for neater installation.
The component wall plate transmitter and receiver units use Cat5e cable to extend the audio and video signal. This is a cost-effective solution based on the broad availability of networking cable which is far more flexible than component video cables, not to mention less expensive.
Unlike some video extension systems, our component extender wall plates also allow you to make use of an existing networking cable (Cat5, Cat6) infrastructure, eliminating the need to re-run cable in the event of an upgrade from component video to another video standard, by simply swapping out the wall plates.
|Warranty Information||Warranty||2 Years|
|Connector(s)||1 - Local Unit Connectors||Component Video (3 x RCA)|
|Digital Coax Audio (RCA)|
|1 - Remote Unit Connectors||Digital Coax Audio (RCA)|
|Component Video (3 x RCA)|
|Cabling||Cat 5 UTP|
|Packaging Information||Package Length||5.9 in [15 cm]|
|Package Width||3.3 in [84 mm]|
|Package Height||4.6 in [11.8 cm]|
|Shipping (Package) Weight||8.1 oz [230 g]|
|Performance||Max Distance||100 m / 330 ft|
|Supported Resolutions||1080i or 720p @ 50m(150ft)
480p or 480i @ 100m(300ft)
|Product Length||4.5 in [11.5 cm]|
|Product Width||2.8 in [70 mm]|
|Product Height||2.4 in [61 mm]|
|Weight of Product||3.5 oz [100 g]|
|What's in the Box||2 - Included in Package||A/V Wall Plate over Cat 5 Extender|
|White Decora Wall-Plates|
|Screw Kits for Wall Plates|
|1 - Included in Package||Instruction Manual|
Make reliable Ethernet connections in applications requiring CMR-rated cable
In stock: US: 0 | CA: 65
Make reliable Ethernet connections in applications requiring CMR-rated cable
In stock: US: 38 | CA: 4
Terminate your Cat5e cables to the exact length required
In stock: US: 346 | CA: 31
There are a few things you'll want to take care of before you deploy your new video extender in your setup.
It’s important to make sure you have everything you will need ahead of time. These items are listed below.
It’s also important to test everything in a simplified setup ahead of time to make sure everything works and that you understand how it works.
In order to set up your video extender, complete the following:
Note: Not all video extenders require external power, or require external power on both ends. Refer to the manual for more information.
Now that you have set up your video extender, you can check that everything is working. You should be able to see your video source's output on the display connected to the video receiver.
If at this point you have further questions regarding a Startech.com video extender, contact our technical support team for further assistance.
When you troubleshoot issues with a video extender, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
Video and Ethernet cables
Video source (such as a DVD player or computer)
Video destination (such as a monitor or projector)
Note: When you are testing setup components, you should avoid using video adapters. For example, if you are converting a VGA source to HDMI for use with an HDMI extender, you should use an HDMI source when you test the components.
To test your setup components, try the following:
Use the cable, video extender, video source, and video destination in another setup to see if the problem is with the components or the setup.
Use a different cable, video extender, video source, and video destination in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.
When you test your cables, it is recommended that you do the following:
Test each cable individually.
Use short cables when you are testing.
When you test the video source and video destination, it is recommended that you do the following:
Remove the video extender from your setup and test to make sure that the video source and video destination work together without the video extender.
Test to make sure that the video source and video destination work together at the resolution that you want to use.
Note: In order for your setup to work properly, the video source, extender, and destination all need to support the resolution that you are using.
You should only use video converters and extenders if it is absolutely necessary to do so. In many cases, most video converters and extenders are not necessary if you purchase the correct cable.
The following table lists the maximum length of cable for common video standards.
|Video standard||Maximum length|
|DisplayPort||50 ft. (15.2m)|
|HDMI||50 ft. (15.2m)|
|DVI||50 ft. (15.2m)|
|VGA||200 ft. (71m)|
Note: StarTech.com offers cables longer than what is listed above, including active cables, which typically include built-in active signal boosters that allow for longer cables. Active cables are specifically designed to exceed the suggested maximum lengths and are tested at the listed specifications (for example, the maximum listed resolution).
Video adapters passively adapt a cable from one connector type to another. Video adapters do not change the signal type, or change the video standard.
Examples of common applications for adapters include the following:
DVI-I to VGA
RCA to BNC
Mini DisplayPort to DisplayPort
Couplers (female to female, or male to male)
Note: You can use a coupler to extend a cable for a short distance. However, each coupler that you use can introduce signal loss, which degrades the signal quality.
Video converters actively process and change the signal type from one video standard and convert it to another standard. They are typically used to convert digital to analog and vice versa, but can be used to convert a digital signal to another digital video standard (for example, HDMI to DisplayPort).
Video converters work over short distances from the source to the destination: up to 15 feet or 3 meters.
Video extenders convert an input signal to a higher voltage for transmission over longer distances and then convert the input signal back to the original video standard. The input and the output signal will match on a video extender, as the same video standard is maintained end-to-end. If a cable is extended with adapters or converters, the signal quality degrades.
Note: For more information on using a video adapter or converter with a video extender, see the following FAQ: http://www.startech.com/faq/video_signal_converters_convert_then_extend.
If you need to use a video extender with a video adapter or converter, you should position the adapter or converter as close to the video source as possible. For example, if you need to take a VGA signal from a computer and send it 200 feet to an HDMI® projector, you should convert the signal from VGA to HDMI and use an HDMI extender.
Note: For more information on when to use cables or extenders, see the following FAQ: http://www.startech.com/faq/video_signal_converters_when_to_convert.
No, this device is designed to be a point-to-point solution using networking cabling only.