Discontinued

2 Port PCI IDE Controller Adapter Card

Add two internal IDE connectors to a computer through a PCI slot

Product ID: PCIIDE2

3 stars (2 reviews) |
  • Two dual channel IDE connectors
  • Support for up to Ultra ATA/133 hard drives with transfer rates up to 133 MBps
  • 48-bit LBA

This 2 Port IDE (Ultra ATA/133) Controller Card can be installed in a PCI slot, to add more IDE storage capability to your PC.

Providing two IDE drive channels with support for two drives per channel and data transfer rates of up to 133 MBps, this adapter card can act as the primary boot device and replace built-in IDE ports, or provide 2 additional high-speed ports to the system. Designed to perform with high-speed IDE/133 drives, the adapter card also supports 100 MBps hard drives, 66 MBps hard drives, 33 MBps hard drives, CD-ROMS, CDRW drives, and other ATA peripherals.

To ensure hassle-free installation, the IDE Controller Card includes Bus-Master drivers for Windows 98/ME/NT 4/2000/XP and Vista™.

Applications

  • Replace a failed IDE port on the motherboard
  • Connect legacy hard drives, CD/DVD drives, ZIP drives, etc to a newer computer system

The StarTech.com Advantage

  • Two dual channel IDE connectors support up to four PATA devices on one card
  • Backed by a StarTech.com lifetime warranty and free lifetime technical support

Partner Numbers

  • Tech Data 10546983
  • ASI 87372
  • SYNNEX US STA-PCIIDE2
  • UPC 065030824330

Compatibility

  • Windows 8 logo
  • Windows Server 2012 logo
  • Linux logo
  • Windows 7 logo
  • Windows 10 logo
  • Windows Server 2016 logo
  • Windows Server 2019 logo
Windows® 98SE, ME, 2000, XP, Vista, 7, 8, 8.1, 10
Windows Server® 2008 R2, 2012, 2016, 2019
Linux

Specifications

Warranty Information Warranty Lifetime
Connector(s) Connector Type(s) 1 - PCI / PCI-X (Universal 3.3 & 5V, 32-bit)
Internal Ports 2 - IDE (40 Pin, EIDE/PATA)
Hardware Ports 2
Interface IDE
Bus Type PCI / PCI-X (5 / 3.3V)
Card Type Standard Profile
Industry Standards ATA/ATAPI-6
Chipset ID ITE - IT8212F
Packaging Information Package Length 8.3 in [21 cm]
Package Width 1.5 in [3.9 cm]
Package Height 5.6 in [143 mm]
Shipping (Package) Weight 0.5 lb [0.2 kg]
Performance Maximum Data Transfer Rate 133 MBps
LBA support 48-bit
Max Drive Capacity Up to 132 GB
Physical Characteristics Product Length 4.7 in [12 cm]
Product Width 0.7 in [18 mm]
Product Height 3.3 in [8.5 cm]
Weight of Product 2.6 oz [73 g]
Software OS Compatibility Windows® 98SE, ME, 2000, XP, Vista, 7, 8, 8.1, 10
Windows Server® 2008 R2, 2012, 2016, 2019
Linux
What's in the Box Included in Package 1 - 2 Port IDE PCI Controller Card
1 - IDE Cable
1 - Driver CD
1 - Instruction Manual

Drivers/Downloads

Talk to an Advisor

We are always ready to assist you with any questions you may have.

Live Chat (opens in new window)

Driver(s):

Manual(s):

Datasheet

Product Support

Talk to an Advisor

We are always ready to assist you with any questions you may have.

Live Chat (opens in new window)

Frequently Asked Questions

Troubleshooting

When you troubleshoot issues with a hard drive controller card, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables

  • Hard drives

  • Hard drive controller card

To test your setup components, try the following:

  • Use the IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in another setup to see if the problem is with the components or the setup.

  • Use a different IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.

  • Use short cables when you are testing.

When you test the hard drive and hard drive controller card, it is recommended that you do the following:

  1. To open the Device Manager, press the Windows key + R, type devmgmt.msc, and press Enter. Check the IDE ATA/ATAPI controllers (for IDE) section, or the Storage controllers (for SATA) section.

  2. Do one of the following:

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.

  2. If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive does not show up in Computer or My Computer until it has a drive letter assigned to it.

Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size

If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.

When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.

There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.

Before You Buy

Note: For more information on how to detect an IDE hard drive, visit http://www.startech.com/faq/hard_drive_accessories_ide_detection.

Older IDE drives are not supported by current StarTech.com products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.

There are a number of reasons that older IDE drives may not be detected, including the following:

  • The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).

  • The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).

  • The sector size is not 512 bytes.

Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.

This device supports the ATA Packet Interface (ATAPI) protocol. ATAPI is required for optical drives, including CD-ROM drives, DVD-ROM drives, and Blu-ray players. Because this device supports ATAPI, optical drives are also supported.

 

Yes. This PCI card uses a universal connector keyed for both 3.3V and 5V that can be used with PCI and PCI-X. This type of connector is identified as having 2 separate notches, instead of just one.

How To

No, this hard drive controller card does not support starting an operating system from a connected hard drive.

For a list of hard drive controller cards that support this feature and instructions on how to configure them, refer to the following FAQ: https://www.startech.com/faq/hard_drive_controllers_os_install_on_controller.

To confirm that Windows detects your expansion card, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
*Product appearance and specifications are subject to change without notice.

Customer Reviews

(2 reviews)
3 out of 5 stars
  • 5 (0)
  • 4 (1)
  • 3 (0)
  • 2 (1)
  • 1 (0)
Tell us what you think of this product.
Need a little help getting started?

Check out our review guidelines.

1 - 2 of 2 Reviews
Sort
(4 Stars)
By: Dougefresh3212 - 08/12/2015
| Helpful?
(2 Stars)
By: lrick - 12/30/2017
I bought one to use for some old pcie ide devices, but it won't work
| Helpful?
Brian, Customer Support on 2/9/2018 12:57:50 PM
Hello, Thanks for letting us know about this. If you haven't yet, we recommend that you contact our Technical Support by clicking the Support button at the top of this webpage. We may be able to offer a solution for you, and if in the event you received a faulty product, we can assist you with sending a replacement.
Feedback Back to top