Discontinued

Dual 2.5in to Single 3.5in IDE Hard Drive Adapter

3.5" Inch Bay IDE to Dual 2.5" HDD Adapter

Product ID: IDE35252X

0 stars (0 reviews) |
  • Jumper for setting Master/Slave modes
  • Supports dual 2.5" IDE hards that mount into a 3.5" drive bay
  • Activity indicator LED

This IDE HDD Adapter allows you to use two 2.5in IDE hard drives in place of a single 3.5in IDE hard drive.

Simply mount two 2.5in IDE hard drives to the IDE35252X adapter and connect the mounted drives to the onboard 44-pin IDE connectors provided. The individual (44-pin) connections are then connected to the computer power supply using a single 40-pin IDE power connection.

This convenient IDE storage adapter also allows users to designate the installed 2.5in drives to operate as either a master or slave drive, and provides a drive activity LED indicator for easy monitoring.

Applications

  • Allows use of multiple 2.5" IDE hard drives in single 3.5" bay

The StarTech.com Advantage

  • Conveniently allows use of Two 2.5" IDE hard drives when only have a single 3.5" drive bay
  • Easy to use and install

Partner Numbers

  • UPC 065030827843

Specifications

Warranty Information Warranty Lifetime
Connector(s) 1 - Connector Type(s) IDE (44 Pin, EIDE/PATA, 2.5" HDD)
IDE (44 Pin, EIDE/PATA, 2.5" HDD)
LP4 (4 pin; Large Drive Power)
IDE (40 Pin, EIDE/PATA)
Environmental Operating Temperature 0°C to 60°C (32°F to 140°F)
Humidity Max 95% RH
Packaging Information Package Length 6.8 in [17.3 cm]
Package Width 1.1 in [28 mm]
Package Height 5.4 in [13.7 cm]
Shipping (Package) Weight 4.2 oz [120.0 g]
Physical Characteristics Color Green
Product Length 5.2 in [13.1 cm]
Product Width 4.0 in [10.2 cm]
Product Height 0.5 in [12 mm]
Weight of Product 2.5 oz [70 g]
What's in the Box 1 - Included in Package 2.5" to 3.5" Adapter
44 Pin Female Cable
Standoff Kit
Screw Kit
Instruction Manual

Drivers/Downloads

Talk to an Advisor

We are always ready to assist you with any questions you may have.

Live Chat (opens in new window)

Manual(s):

Datasheet

Product Support

Talk to an Advisor

We are always ready to assist you with any questions you may have.

Live Chat (opens in new window)

Frequently Asked Questions

Troubleshooting

Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size

If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.

When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.

There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.

Before You Buy

Note: For more information on how to detect an IDE hard drive, visit http://www.startech.com/faq/hard_drive_accessories_ide_detection.

Older IDE drives are not supported by current StarTech.com products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.

There are a number of reasons that older IDE drives may not be detected, including the following:

  • The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).

  • The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).

  • The sector size is not 512 bytes.

Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.

Compliance and safety

Compliance letters

  • WEEE
    • Language: English
  • RoHS
    • Language: English

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
*Product appearance and specifications are subject to change without notice.

Customer Reviews

(0 reviews)
0 out of 5 stars
  • 5 (0)
  • 4 (0)
  • 3 (0)
  • 2 (0)
  • 1 (0)
Tell us what you think of this product.
Need a little help getting started?

Check out our review guidelines.

Feedback Back to top