Are you in the United States?
Visit our U.S.A. & International site for relevant pricing, distribution and product availability information.
Go to StarTech.com1-poort PCI Express IDE Controllerkaart
Voeg een 2-kanaals IDE-poort toe aan een computer via een PCI Express-slot
Productcode: PEX2IDE
- 2-kanaals IDE-poort ondersteunt twee schijven
- Ondersteuning voor 48-bit LBA
- Ondersteunt ATA/ATAPI-commando's
- Ondersteunt UDMA-6 voor overdrachtsnelheden tot 133 MB/s
- Inclusief low profile montagebracket
Toepassingen
- Voeg een IDE-poort toe aan een computersysteem
- Vervang een defecte IDE-poort
- Voeg een IDE-poort toe voor het aansluiten van oudere ATA-apparaten, zoals harde schijven en tapedrives
StarTech.com Voordeel
- 2 kanalen ondersteunen twee IDE-schijven tegelijk met ondersteuning voor UDMA-6 gegevensoverdracht
- Ondersteuning voor 48-bit LBA voor compatibiliteit met hoge-capaciteit harde schijven van meer dan 137 GB
- Met levenslange garantie en gratis technische ondersteuning door StarTech.com
Productnummers
Ingram Micro Netherlands
1595736
Tech Data - Netherlands
4462103
UPC Code
065030825153
Technische specificaties
Garantie | ||
---|---|---|
Garantie | Lifetime | |
Hardware | ||
Bus type | PCI Express | |
Chipsetcode | JMicron - JMB368 | |
Interface | IDE | |
Kaarttype | Standaard bracket (incl. low profile bracket) | |
Poorten | 1 | |
Prestaties | ||
LBA-ondersteuning | 48-bit | |
Connector(en) | ||
Interne poorten | 1 - IDE (40-polig, EIDE/PATA) Mannelijk | |
Type connector(en) | 1 - PCI Express x1 Mannelijk | |
Software | ||
Besturingssystemen | Windows® 2000, XP, Vista, 7, 8, 8.1, 10 Windows Server® 2008 R2, 2012, 2016, 2019 |
|
Speciale opmerkingen / vereisten | ||
Systeem- en kabelvereisten | Vrije PCI Express-uitbreidingsslot | |
Fysieke eigenschappen | ||
Gewicht product | 120 g [4.2 oz] | |
Verpakkingsinformatie | ||
Package Height | 42 mm [1.7 in] | |
Package Length | 23 cm [9.1 in] | |
Package Width | 16.5 cm [6.5 in] | |
Verzendgewicht (verpakt) | 0.2 kg [0.4 lb] | |
Wat wordt er meegeleverd | ||
Meegeleverd | 1 - PCI Express IDE Controllerkaart | |
1 - IDE-kabel | ||
1 - Low-profile bracket | ||
1 - Handleiding |
Compatibiliteit






Windows Server® 2008 R2, 2012, 2016, 2019
Productondersteuning
Handleidingen
-
PEX2IDE.pdf
- Taal: Engels
Specificatiebladen
-
PEX2IDE_Datasheet-NL.pdf
- Taal: Nederlands
Veelgestelde vragen (FAQ)
Voor uw aanschaf
Note: For more information on how to detect an IDE hard drive, visit http://www.startech.com/faq/hard_drive_accessories_ide_detection.
Older IDE drives are not supported by current StarTech.com products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.
There are a number of reasons that older IDE drives may not be detected, including the following:
-
The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).
-
The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).
-
The sector size is not 512 bytes.
Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.
Copy Link
Heeft deze informatie u geholpen? Ja Nee
This device supports the ATA Packet Interface (ATAPI) protocol. ATAPI is required for optical drives, including CD-ROM drives, DVD-ROM drives, and Blu-ray players. Because this device supports ATAPI, optical drives are also supported.
Copy Link
Heeft deze informatie u geholpen? Ja Nee
Hoe gaat u te werk
To confirm that Windows detects your expansion card, complete the following:
- Press the Windows key+R, type devmgmt.msc, and press Enter.
- In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it. For example, a USB controller card would be under Universal Serial Bus controllers.
Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.
Copy Link
Heeft deze informatie u geholpen? Ja Nee
No, this hard drive controller card does not support starting an operating system from a connected hard drive.
For a list of hard drive controller cards that support this feature and instructions on how to configure them, refer to the following FAQ: https://www.startech.com/faq/hard_drive_controllers_os_install_on_controller.
Copy Link
Heeft deze informatie u geholpen? Ja Nee
Troubleshooting
Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size
If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.
When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.
There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.
Copy Link
Heeft deze informatie u geholpen? Ja Nee
When you troubleshoot issues with a hard drive controller card, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
-
IDE, SATA, and eSATA cables
-
Hard drives
-
Hard drive controller card
To test your setup components, try the following:
-
Use the IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in another setup to see if the problem is with the components or the setup.
-
Use a different IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.
When you test your cables, it is recommended that you do the following:
-
Test each cable individually.
-
Use short cables when you are testing.
When you test the hard drive and hard drive controller card, it is recommended that you do the following:
-
To open the Device Manager, press the Windows key + R, type devmgmt.msc, and press Enter. Check the IDE ATA/ATAPI controllers (for IDE) section, or the Storage controllers (for SATA) section.
-
Do one of the following:
-
If you do not see the hard drive controller card in Device Manager, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=expansion-cards#pci-pcie-cannot-boot-os-or-detect-windows.
-
If the device is listed with an error, reinstall the drivers by completing the instructions on the website.
-
If the hard drive is listed with unallocated space, the hard drive needs to be formatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
-
To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
-
If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.
Note: A formatted hard drive does not show up in Computer or My Computer until it has a drive letter assigned to it.
Copy Link
Heeft deze informatie u geholpen? Ja Nee
Compliance and Safety
Compliance Letters
-
Country of Origin (COO)
- Taal: Engels
-
Declaration of Conformity (DOC)
- Taal: Engels
-
Waste Electrical and Electronic Equipment Directive (WEEE)
- Taal: Engels
Safety Measures
- Als de printplaat van het product niet is afgedekt, mag het onder spanning staande product niet worden aangeraakt.
- Bij een klasse 1 laserproduct zal er laserstraling aanwezig zijn als het systeem open is.
- Bedrading mag niet worden afgeklemd als het product en/of de elektrische kabels onder spanning staan.
- Het product moet door een gecertificeerde professional geïnstalleerd en/of gemonteerd worden volgens de plaatselijke veiligheidsvoorschriften en bouwverordening.
- Kabels (inclusief voedings- en laadkabels) moeten zo worden geplaatst en aangelegd dat struikelen wordt voorkomen en elektrische en veiligheidsrisico’s worden vermeden.
* Uitvoering en specificaties van het product zijn zonder aankondiging vatbaar voor wijzigingen.