Product ID: PEX2IDE
In stock: 237
This PCI Express IDE Controller Adapter Card provides a cost-effective way to use legacy drives with modern computers, by converting a PCI Express port into an IDE port.
Providing data burst transfer rates of up to 133MBps and support for PIO 0/1/2/3/4 and UDMA 33/66/100/133 operating modes, the IDE controller card offers an efficient way to add an IDE channel with support for two IDE drives on the same channel.
A complete dual profile solution, the PCI Express IDE controller card provides both standard and low profile brackets for adapting to slimline or small form factor system applications.
|Connector(s)||1 - Connector Type(s)||PCI Express x1|
|1 - Internal Ports||IDE (40 Pin, EIDE/PATA)|
|Bus Type||PCI Express|
|Card Type||Standard Profile (LP bracket incl.)|
|Chipset ID||JMicron - JMB368|
|Packaging Information||Package Length||23.0 cm [9.1 in]|
|Package Width||16.5 cm [6.5 in]|
|Package Height||4.2 cm [1.7 in]|
|Shipping (Package) Weight||200.0 g [7.1 oz]|
|Product Length||5.2 cm [2.0 in]|
|Product Width||2.2 cm [0.9 in]|
|Product Height||12.0 cm [4.7 in]|
|Weight of Product||120.0 g [4.2 oz]|
|Software||OS Compatibility||Windows® 2000, XP, Vista, 7, 8, 8.1, 10, 11
Windows Server® 2008 R2, 2012, 2016, 2019
|Special Notes / Requirements||System and Cable Requirements||Available PCI Express expansion slot|
|What's in the Box||1 - Included in Package||PCI Express IDE Controller Card|
|Low Profile Bracket|
Connect two ATA devices to a computer IDE controller
Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size
If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.
When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.
There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.
When you troubleshoot issues with a hard drive controller card, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
IDE, SATA, and eSATA cables
Hard drive controller card
To test your setup components, try the following:
Use the IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in another setup to see if the problem is with the components or the setup.
Use a different IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.
When you test your cables, it is recommended that you do the following:
Test each cable individually.
Use short cables when you are testing.
When you test the hard drive and hard drive controller card, it is recommended that you do the following:
To open the Device Manager, press the Windows key + R, type devmgmt.msc, and press Enter. Check the IDE ATA/ATAPI controllers (for IDE) section, or the Storage controllers (for SATA) section.
Do one of the following:
If you do not see the hard drive controller card in Device Manager, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=expansion-cards#pci-pcie-cannot-boot-os-or-detect-windows.
If the device is listed with an error, reinstall the drivers by completing the instructions on the website.
If the hard drive is listed with unallocated space, the hard drive needs to be formatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.
Note: A formatted hard drive does not show up in Computer or My Computer until it has a drive letter assigned to it.
To confirm that Windows detects your expansion card, complete the following:
Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.
No, this hard drive controller card does not support starting an operating system from a connected hard drive.
For a list of hard drive controller cards that support this feature and instructions on how to configure them, refer to the following FAQ: https://www.startech.com/faq/hard_drive_controllers_os_install_on_controller.
Note: For more information on how to detect an IDE hard drive, visit http://www.startech.com/faq/hard_drive_accessories_ide_detection.
Older IDE drives are not supported by current StarTech.com products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.
There are a number of reasons that older IDE drives may not be detected, including the following:
The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).
The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).
The sector size is not 512 bytes.
Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.
This device supports the ATA Packet Interface (ATAPI) protocol. ATAPI is required for optical drives, including CD-ROM drives, DVD-ROM drives, and Blu-ray players. Because this device supports ATAPI, optical drives are also supported.
Check out our review guidelines.