Product ID: 110VDSLEXT
The 110VDSLEXT VDSL Ethernet extender kit lets you span a 10/100 network over extremely long distances (up to 1km) while still maintaining high-speed network connectivity, allowing you to run the connection over standard RJ45 cabling, existing RJ11 phone lines, or any other set of single pair wires. The VDSL (VDSL2) kit is simple to install and provides an out-of-the-box solution as both the Ethernet-VDSL extender and receiver units are included.
A perfect solution for a broad range of applications including connecting isolated user stations within the same building or between separate buildings, or overcoming infrastructure obstacles and distances (e.g. older stone/concrete architecture) where new wiring or wireless may be impossible. The VDSL Ethernet LAN Extender kit helps to eliminate expense by allowing video streaming and data to share the same telephone pair without interference.
Backed by a StarTech.com 2-year warranty and free lifetime technical support.
|Warranty Information||Warranty||2 Years|
|Connector(s)||2 - Local Unit Connectors||RJ-45|
|2 - Remote Unit Connectors||RJ-45|
|Environmental||Operating Temperature||0°C to 50°C (32°F to 122°F)|
|Storage Temperature||0°C to 70°C (32°F to 158°F)|
|Hardware||Industry Standards||IEEE 802.3/802.3u/802.3x
10/100 Base-T Auto-Negotiation, Auto-MDI/MDI-X
On-board surge protection
|VDSL2 ITU-T G.993.2, VDSL ITU-T G.993.1, and VDSL2/VDSL ITU-T G.997.1 compliant|
|Indicators||3 - LED Indicators||LAN: ACT/LNK, 10/100 Mbps, Half/Full Duplex|
|VDSL: Power On/Off, CO/CPE, Idle/Trained/Link|
|Packaging Information||Package Height||13.3 cm [5.2 in]|
|Package Length||15.3 cm [6.0 in]|
|Shipping (Package) Weight||696 g [24.6 oz]|
|Package Width||18.3 cm [7.2 in]|
|Performance||Maximum Data Transfer Rate||0m - 100Mbit/s
300m - 75Mbit/s
1km - 10Mbit/s
|Max Distance||1 km (0.6 mi)|
|Physical Characteristics||Weight of Product||173 g [6.1 oz]|
|Product Length||95 mm [3.7 in]|
|Product Width||72 mm [2.8 in]|
|Product Height||22 mm [0.9 in]|
|Power||Power Source||2 AC Adapters Included|
|Output Voltage||12V DC|
|Center Tip Polarity||Positive|
|Special Notes / Requirements||Note||You have the ability to use up to four sets over a single Cat5e or Cat6 cable which can be used as separate LAN (or VLAN) connections, or bridged into a trunk line for additional speed/bandwidth over long distances (Up to two sets only over standard Cat5).|
|What's in the Box||1 - Included in Package||Ethernet VDSL Extender|
|Ethernet VDSL Receiver|
|2 - Included in Package||RJ-45 to VDSL Cable|
Make Gigabit network connections using this high quality Cat6 Cable
Extend your 10/100Mbps network by up to 1km over Ethernet or RJ11 phone lines
Replace your lost or failed power adapter
When you troubleshoot issues with a VDSL Extender, there are some quick tests that you can complete to rule out potential problems. To identify what the source of the issue is, observe the power LED, LAN LED, and VDSL LED on the units.
If the power LED is not illuminated for the transmitter or the receiver, complete the following:
If another LED is not operating as expected, make sure that the components in your setup are working correctly. To test your setup components, try the following:
When you test your cables, it is recommended that you do the following:
Make sure that the DIP switches are set to the following:
If there is still no VDSL connection or if there is intermittent connection issues, try the following:
If you cannot establish a network connection between your remote and local units, you need to do the following to make sure that the issue is not related to the network configuration:
If the issue is not related to the network configuration, you should receive a response from Computer 2.
For more information on how to ping another network device, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=networking#ping-test-windows-mac-os.
Check out our review guidelines.