Productcode: IDE2SAT2
Met de IDE2SAT2 40-polige IDE-naar-SATA-adapter kunt u een SATA I/II/III schijf aansluiten op een beschikbare IDE/ATA 33/66/100/133 moederbordpoort - een voordelige oplossing waardoor u nieuwe SATA-schijven kunt toevoegen en uw bestaande moederbord kunt behouden.
De IDE/SATA-adapter is een voordelige oplossing voor de overbrugging van het verschil tussen een nieuwere 2,5"/3,5"/5,25" SATA-schijf en een oudere IDE-moederbordpoort. De IDE2SAT2 ondersteunt ook ODD (Optical Disk Drive), waardoor u Blu-ray-, dvd- of cd-rom-schijven aan een ouder IDE-moederbord kunt toevoegen.
De IDE/SATA-adapter wordt gedekt door een StarTech.com 2-jarige garantie en gratis levenslange technische ondersteuning.
Warranty Information | Warranty | 2 Years |
---|---|---|
Connector(en) | 1 - Type connector(en) | SP4 (4-polig, Small Drive Power) |
IDE (40-polig, EIDE/PATA) | ||
SATA data & voeding combinatie (7+15-polig) | ||
Fysieke eigenschappen | Gewicht product | 29 g [1,0 oz] |
Type behuizing | Staal | |
Lengte product | 75,5 mm [3,0 in] | |
Breedte product | 20 mm [0,8 in] | |
Hoogte product | 23 mm [0,9 in] | |
Gebruiksomgeving | Bedrijfstemperatuur | 5°C to 50°C (40°F to 122°F) |
Opslagtemperatuur | -25°C to 80°C (-13°F to 176°F) | |
Vochtigheid | 15% - 90% rel. luchtvochtigheid | |
Hardware | Interface | IDE |
Aantal stations | 1 | |
Schijfgrootte | 2.5in & 3.5in | |
Schijftype | SATA | |
Chipsetcode | Marvell - 88SA8052 | |
Prestaties | Maximale overdrachtsnelheid | 133MB/sec |
RAID | Nee | |
Software | Besturingssystemen | OS independent; No software or drivers required |
Speciale opmerkingen / vereisten | Systeem- en kabelvereisten | IDE-controller en ATA-kabel (niet meegeleverd). |
Verpakkingsinformatie | Package Height | 33 mm [1,3 in] |
Package Length | 14,5 cm [5,7 in] | |
Verzendgewicht (verpakt) | 89 g [3,1 oz] | |
Package Width | 17,5 cm [6,9 in] | |
Wat wordt er meegeleverd | 1 - Meegeleverd | IDE naar SATA Adapter |
Voedingskabel van LP4 Molex naar SP4 | ||
Handleiding |
Sluit twee LP4-randapparaten (CD/DVD-ROM drives etc.) aan op een enkele LP4-connector
Zet vrijwel elke 2,5 inch SATA of SAS harde schijf om in een 3,5 inch SATA-schijf
Monteer een 3,5 inch harde schijf in een desktopcomputer met een beschikbare 5,25 inch bay
Connect two ATA 100/133 drives to a computer IDE controller
Sluit twee harde schijven aan op een IDE-controller in een computer
Sluit twee harde schijven aan op een IDE-controller in een computer
Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size
If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.
When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.
There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.
Note: For more information on how to detect an IDE hard drive, visit http://www.startech.com/faq/hard_drive_accessories_ide_detection.
Older IDE drives are not supported by current StarTech.com products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.
There are a number of reasons that older IDE drives may not be detected, including the following:
The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).
The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).
The sector size is not 512 bytes.
Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.