1:2 standalone USB duplicator en -wisser voor Flash drives

USB kloner | 1.5GB per minuut | USB 2.0 | TAA conform

Productcode: USBDUP12

  • Dupliceer of wis tegelijkertijd twee USB schijven zonder aansluiting op een computer, met deze standalone USB duplicator
  • Verwijder en vervang een schijf, terwijl de andere schijf doorgaat met kopiëren, met asynchrone duplicatie
  • Voer een systeem-en-bestand-duplicatie of een volledige schijfduplicatie uit met deze USB cloner
Uw prijs
€193,99 EUR excl. BTW
€234,73 EUR incl. BTW

Met deze standalone USB duplicator kunt u twee flashdrives klonen of wissen zonder aansluiting op een hostcomputer. 

1:2 schijfduplicatie 

Met de USB cloner kunt u tegelijkertijd tot twee schijven kopiëren (synchrone duplicatie) met snelheden tot 1,5 GB per minuut. Hij biedt ook asynchrone duplicatie waarmee u de ene schijf kunt verwijderen en vervangen, terwijl de andere schijf blijft kopiëren.  

De duplicator heeft twee duplicatiemodi: systeem-en-bestand of hele schijf. Systeem-en-bestand leidt tot een kortere duplicatietijd, waarbij partities en opgeslagen gegevens worden gekopieerd, terwijl alle secties met lege ruimte worden genegeerd. Bij hele schijf wordt elke sector van de schijf gedupliceerd (spiegelbeeld). Deze duplicatiemodus is ideaal wanneer u alles op de schijf moet kopiëren, inclusief verborgen gegevens.   

Wis twee schijven tegelijkertijd 

Met de USB flashdrive duplicator kunt u tegelijkertijd twee USB schijven wissen, waarbij diverse wismodi worden ondersteund waaronder: 

  • Snel wissen 
  • Volledig wissen 
  • Beveiligd wissen 

Beveiligd wissen voldoet aan internationale vereisten, waaronder de nieuwe NIST-normen (SP 800-88 Rev1), waarmee wordt gewaarborgd dat alle schijven correct worden gewist. 

Gemakkelijk te gebruiken 

De standalone USB duplicator heeft een LCD-scherm zodat u het wissen en dupliceren in de gaten kunt houden en weet of dit succesvol was. Hij heeft ook vier sneltoetsen voor eenvoudige bediening. 

USBDUP12 is TAA-conform en wordt gedekt door een 2-jarige garantie en gratis levenslange technische ondersteuning van StarTech.com. 

Toepassingen

  • Snelle back-up van USB flashdrives, gegevensherstel en wissen van de schijf
  • Maak een exacte replica van een USB bronschijf, inclusief verborgen gegevens, op twee USB doelschijven
  • Wis alle gegevens van een flashdrive

Het voordeel van StarTech.com

  • Dupliceert twee doel-flashdrives gelijktijdig, zonder aansluiting op een computer
  • Bespaar tijd door alleen de inhoud van een flashdrive te kopiëren, in tegenstelling tot het gehele volume
  • Uiterst veelzijdig dupliceren van een USB-flashdrive naar een HDD/SSD of ander flashmedium via een USB-dock, behuizing of kaartlezer

Partnernummers

  • Ingram Micro Netherlands 2408522
  • UPC 065030849944

Compatibility

Specificaties

Warranty Information Warranty 2 Years
Connector(en) 3 - Schijfaansluitingen USB Type-A (4-polig) USB 2.0
Fysieke eigenschappen Kleur Zwart
Type behuizing Kunststof
Lengte product 12 cm [4,7 in]
Breedte product 13 cm [5,1 in]
Hoogte product 2,5 cm [1,0 in]
Gewicht product 190 g [6,7 oz]
Gebruiksomgeving Bedrijfstemperatuur 5°C ~ 45°C (41°F ~ 113°F)
Opslagtemperatuur -20°C ~ 85°C (-4°F ~ 185°F)
Vochtigheid 5% - 95% rel. luchtvochtigheid
Hardware Bus type USB 2.0
Aantal stations 3
Schijftype USB-flashdrive
Schijfinstallatie Verwijderbaar
Buffergrootte 64 MB
Indicatoren 3 - LED-indicatoren Groen (actief/succesvol kopiëren)
Rood (fout)
Prestaties Duplication Modes System and File
Sector by Sector (Whole Drive)
Wismodi Quick Erase
1-Pass Overwrite (NIST SP 800-88 Rev 1 - Clear)
3-Pass Overwrite
Duplication Speed 1.5GBpm
Max. schijfcapaciteit 2TB
MTBF 176,549 hours
Software Besturingssystemen Onafhankelijk van besturingssysteem; Geen software of drivers nodig
Speciale opmerkingen / vereisten Notitie Voor duplicatie dient de doelschijf een capaciteit te hebben die gelijk is aan of groter is dan de bronschijf.
Deze duplicator heeft 64 MB niet-vluchtig flashgeheugen voor de opslag van firmware- en chipsetprocedures en 64 MB vluchtig DDR3 geheugen voor programmatoegangsdata
Ondersteunt het kopiëren/klonen/wissen naar/van SD / SDHC / Micro SD / MMC / Mini SD / CF-media via een USB-multimediakaartlezer (apart verkrijgbaar), en naar harde schijven of solid-state drives via een harddisk docking station of USB-behuizing (apart verkrijgbaar), indien ondersteund door de opslagmedia
Verpakkingsinformatie Package Height 77 mm [3,0 in]
Package Length 21,3 cm [8,4 in]
Package Width 16,8 cm [6,6 in]
Verpakkingsaantal 1
Verzendgewicht (verpakt) 550 g [19,4 oz]
Voeding Inclusief voedingsadapter Inclusief wisselstroomadapter
Ingangsspanning 100 - 240 AC
Uitgangsspanning 5 DC
Uitgangsstroom 2
Polariteit pin midden Positief
Stekkertype H
Vermogensopname 10
Wat wordt er meegeleverd 1 - Meegeleverd Duplicator
universele voedingsadapter
handleiding
3 - Meegeleverd Stekker voor voedingsadapter (NA/GB/EU)

Accessoires

Niet meer leverbaar
FCREADMICRO

USB Multimedia Geheugenkaartlezer Adapter

Voeg een compacte externe geheugenkaartlezer toe aan iedere computer met een USB-poort

Uw prijs
€16,99 EUR excl. BTW
€20,56 EUR incl. BTW
Niet meer leverbaar
SAT2510U2

2,5 inch Zilver USB 2.0 naar SATA Externe Harde Schijf Behuizing

Maak van een 2,5 inch SATA-schijf een extern opslagapparaat met USB 2.0-connectiviteit

Uw prijs
€16,99 EUR excl. BTW
€20,56 EUR incl. BTW
SVA5H2NEUA

DC power adapter - 5V, 2A voedingsadapter

Vervang uw zoekgeraakte of defecte voedingsadapter

Uw prijs
€19,99 EUR excl. BTW
€24,19 EUR incl. BTW

Drivers/Downloads

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Firmware

Handleiding:

Datasheet

Productondersteuning

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Veelgestelde vragen (FAQ)

Troubleshooting

When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables
  • Hard drives
  • Hard drive dock or duplicator

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive dock or duplicator in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive dock or duplicator in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:

Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  2. Do one of the following:
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive. 

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.

The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.

Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.

Extend a partition on a computer running Windows

Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.

After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:

  1. Press the Windows key + R.
  2. Type compmgmt.msc and click Ok.
  3. In Computer Management, on the left side of the screen, click Disk Management.
  4. Find the target drive. It will most likely be at the bottom of the list, have a partition that is the same size as the source drive, and have an unallocated area on the drive.
  5. On the target drive, right-click the last partition on the right side of the screen and click Extend Volume.
  6. In the Extend Volume wizard, click Next. By default, the remaining drive area is the amount of space used.
  7. Click Next > Finish.

The primary partition on the drive now uses the entire drive area.

StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode .  A duplication that fails or halts will not cause a problem with the source drive.

You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.

Voor uw aanschaf

StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.

If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.

Software-level encryption on the drive poses no issue to StarTech.com duplicators, as the duplicators copy encrypted data sector by sector over to the new drive.

Hardware-level encryption or BIOS level hard drive locks cause the duplication to halt and fail, as the drive is unable to read or write the sectors that are encrypted.

Duplication of Hidden Protected Area (HPA) Partitions or Extended Industry Standard Architecture (EISA) cause the duplicator to halt and fail, as the drive cannot read and write the protected partitions on the drive.

Note: Our UNIDUPDOCKSATDOCK22RE and SATDOCK4U3RE do include the ability to copy HPA partitions, but the duplication is still dependent on how the HPA partition is written to the hard drive, whether or not it is encrypted and how it is encrypted.

StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.

SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.

Quick and secure erase functions

Quick erase and secure erase are functions the duplicators call on the hard drives themselves. How they work depends on the manufacturer of the hard drive.

Department of Defense erase function

A Department of Defense (DoD) erase is a function performed by the duplicator where it does three passes. The first pass writes all 0s. The second pass writes all 1s. The third pass writes 0s and 1s randomly.

Note: Not all duplicators will feature all of these erase modes. It is important to review the product manual to confirm the available erase modes.

Although the USB flash drive duplicators are intended for use with USB flash drives, they can be used with external hard drives.

Note: Due to the slower copy speed of the USB flash drive enclosures, using an external hard drive as the source of the copy can take a considerable amount of time. USBDUP12 and USBDUP15 both copy at 1.5 GB per minute. Therefore, if you use a 1 TB external hard drive as the source of a copy, it would take roughly 11 hours to complete.

Hard Drives

Windows 10 

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).

Initialize a drive

Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.

  1. Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.

  2. Navigate to Disk Management.

  3. When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.

  4. Click OK.

Create a partition in a drive

Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.

  1. Right-click Unallocated or RAW volume, and select New Simple Volume.

  2. In the New Partition Wizard, click Next.

  3. Select Primary partition.

  4. Leave the partition size set to default, and click Next.

  5. Assign a drive letter or leave it set to the default, and click Next.

  6. Enter the following settings to format the partition:

  • In the File System field, enter NTFS.
  • Set the Allocation unit size to Default.
  • In the Volume label field, enter <your name/reference>.
  • Select the Perform a quick format check box.
  • Clear the Enable file and folder compression check box.
  1. Click Next > Finish.

The new drive should appear in Windows Explorer.

Mac OS

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).

Initialize a drive

Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.

Create a partition on a drive

Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.

To create a partition on a new drive, complete the following:

  1. Open Finder.

  2. Navigate to Applications and click Utilities.

  3. Open Disk Utility.

  4. Select the new drive and click the Partition tab.

  5. Click Options and verify that it is set to GUID Partition Table.

  6. Enter a name for the partition.

  7. Click Partition.

The drive should now be accessible in Finder.

 

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Uitvoering en specificaties van het product zijn zonder aankondiging vatbaar voor wijzigingen.
Wacht...
Terug naar boven