Productcode: USBDUP15
Met de USBDUP15 OnetoFive USB-flashdriveduplicator en -wisser kunt u snel maximaal vijf back-ups maken van één USB-flashdrive, of veilig maximaal vijf flashdrives wissen, zonder aangesloten te zijn op een hostcomputer.
Deze lichtgewicht flashdriveduplicator en -wisser kunt u overal meenemen, neemt weinig plaats in beslag in de desktop en vereist geen hostcomputer omdat hij standalone werkt. Perfect voor de verspreiding van software- en marketingmaterialen op kantoor en onderweg.
Met een gemakkelijk leesbaar LCD-scherm en intuïtieve menubediening met vier toetsen garandeert de USBDUP15 probleemloze installatie en bediening. In het menu hebt u met drukknoppen toegang tot vele waardevolle functies, waardoor het takenbeheer wordt vereenvoudigd zoals: capaciteit & snelheidscontrole, kopiëren & vergelijken, asynchroon kopiëren en nog veel meer. Het biedt ook talrijke geavanceerde instelopties voor ervaren gebruikers.
Dit veelzijdige apparaat is een gecombineerde harde-schijf-kloner en -wisser en biedt twee duplicatiemodi (Bestand & Systeem kopiëren / Volledig kopiëren) met max. 1,5 GB/m in de modus Alles kopiëren. Het biedt drie wismodi (Snel wissen / Volledig wissen / DoD-wissen) waarmee u zelf de beste oplossing voor uw applicatie kunt kiezen.
De USBDUP15 is TAA-compatibel en wordt gedekt door een 2-jarige garantie en levenslange technische ondersteuning van StarTech.com.
Warranty Information | Warranty | 2 Years |
---|---|---|
Connector(en) | 6 - Schijfaansluitingen | USB Type-A (4-polig) USB 2.0 |
Fysieke eigenschappen | Kleur | Zwart |
Type behuizing | Kunststof | |
Lengte product | 16,7 cm [6,6 in] | |
Breedte product | 12 cm [4,7 in] | |
Hoogte product | 25 mm [1,0 in] | |
Gewicht product | 318 g [11,2 oz] | |
Gebruiksomgeving | Bedrijfstemperatuur | 5°C ~ 45°C (41°F ~ 113°F) |
Opslagtemperatuur | -20°C ~ 85°C (-4°F ~ 185°F) | |
Vochtigheid | 5% - 95% rel. luchtvochtigheid | |
Hardware | Bus type | USB 2.0 |
Aantal stations | 6 | |
Schijftype | USB-flashdrive | |
Schijfinstallatie | Verwijderbaar | |
Buffergrootte | 64 MB | |
Indicatoren | 5 - LED-indicatoren | Groen (actief/succesvol kopiëren) |
Rood (fout) | ||
Prestaties | Duplication Modes | System and File |
Duplication Speed | 1.5GBpm | |
Wismodi | Quick Erase | |
Max. schijfcapaciteit | 2TB | |
Duplication Modes | Sector by Sector (Whole Drive) | |
Wismodi | 1-Pass Overwrite (NIST SP 800-88 Rev 1 - Clear) | |
3-Pass Overwrite | ||
MTBF | 176,549 hours | |
Software | Besturingssystemen | Onafhankelijk van besturingssysteem; Geen software of drivers nodig |
Speciale opmerkingen / vereisten | Systeem- en kabelvereisten | Voor duplicatie moeten de doelschijven dezelfde capaciteit hebben als of een grotere capaciteit hebben dan de bronschijf. |
Ondersteunt het kopiëren/klonen/wissen naar/van SD / SDHC / Micro SD / MMC / Mini SD / CF-media via een USB-multimediakaartlezer (apart verkrijgbaar), en naar harde schijven of solid-state drives via een harddisk docking station of USB-behuizing (apart verkrijgbaar), indien ondersteund door de opslagmedia | ||
Verpakkingsinformatie | Package Height | 82 mm [3,2 in] |
Package Length | 23,1 cm [9,1 in] | |
Package Width | 18 cm [7,1 in] | |
Verzendgewicht (verpakt) | 742 g [26,2 oz] | |
Voeding | Inclusief voedingsadapter | Inclusief wisselstroomadapter |
Ingangsspanning | 100 - 240 AC | |
Uitgangsspanning | 5 DC | |
Uitgangsstroom | 2 | |
Polariteit pin midden | Positief | |
Stekkertype | H | |
Vermogensopname | 10 | |
Wat wordt er meegeleverd | 1 - Meegeleverd | Duplicator |
Universele voedingsadapter: is geschikt voor NA/EU/GB wanneer gekocht in NA/EU/GB; is geschikt voor Australië en Nieuw-Zeeland wanneer gekocht in Australië en Nieuw-Zeeland. | ||
Handleiding |
Voeg een compacte externe geheugenkaartlezer toe aan iedere computer met een USB-poort
Maak van een 2,5 inch SATA-schijf een extern opslagapparaat met USB 2.0-connectiviteit
Dock uw 2,5 of 3,5 inch SATA SSD's/HDD's en voeg een snelle oplaadmogelijkheid via USB toe in een stijlvol docking station
Dock uw 2,5 of 3,5 inch SATA SSD's/HDD's en voeg een snelle-oplaadmogelijkheid via USB toe in een stijlvol wit docking station
Dok max. twee 2,5 inch of 3,5 inch SATA SSD's/HDD's in een stijlvol zwart dockingstation met een geïntegreerde 2-poorts USB 3.0 hub
Sluit een 2,5 inch of 3,5 inch SATA harde schijf aan op uw computer via USB 3.0 of eSATA
Dock uw 2,5 of 3,5 inch SATA III SSD's/HDD's via USB 3.0 met UASP
Snelle hot-swappable toegang tot uw 2,5 of 3,5 inch SATA harde schijven, aangesloten via USB 3.0
Dok uw 2,5 inch of 3,5 inch ” SATA SSD's/HDD's in een stijlvol wit dockingstation met een geïntegreerde 3-poorts USB 3.0 hub
Maak externe, verwisselbare toegang mogelijk tot 2,5 inch SATA-schijven vanaf een draagbare mini USB 2.0 Drive Dock
Verander een 3,5 inch SATA harde schijf in een door UASP ondersteunde USB 3.0 externe harde schijf
Verander een 3,5 inch SATA harde schijf in een door UASP ondersteunde USB 3.0 externe harde schijf
Verander een 2,5 inch SATA harde schijf of solid-state drive in een door UASP ondersteunde USB 3.0 externe harde schijf
Verander een 2,5 inch SATA harde schijf of solid-state drive in een door UASP ondersteunde USB 3.0 externe harde schijf
Verander een 2,5” SATA harde schijf in drie onafhankelijke virtuele optische drives, of een draagbare USB 3.0 opslagoplossing
Verander een 2,5 inch SATA HDD/SSD in een volledige externe opslagoplossing via USB 3.0 met UASP
Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
To test your setup components, try the following:
When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:
Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.
You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.
The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.
Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.
Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.
After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:
The primary partition on the drive now uses the entire drive area.
StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode . A duplication that fails or halts will not cause a problem with the source drive.
You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.
StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.
If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.
Software-level encryption on the drive poses no issue to StarTech.com duplicators, as the duplicators copy encrypted data sector by sector over to the new drive.
Hardware-level encryption or BIOS level hard drive locks cause the duplication to halt and fail, as the drive is unable to read or write the sectors that are encrypted.
Duplication of Hidden Protected Area (HPA) Partitions or Extended Industry Standard Architecture (EISA) cause the duplicator to halt and fail, as the drive cannot read and write the protected partitions on the drive.
Note: Our UNIDUPDOCK, SATDOCK22RE and SATDOCK4U3RE do include the ability to copy HPA partitions, but the duplication is still dependent on how the HPA partition is written to the hard drive, whether or not it is encrypted and how it is encrypted.
StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.
SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.
Although the USB flash drive duplicators are intended for use with USB flash drives, they can be used with external hard drives.
Note: Due to the slower copy speed of the USB flash drive enclosures, using an external hard drive as the source of the copy can take a considerable amount of time. USBDUP12 and USBDUP15 both copy at 1.5 GB per minute. Therefore, if you use a 1 TB external hard drive as the source of a copy, it would take roughly 11 hours to complete.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).
Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.
Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.
Navigate to Disk Management.
When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.
Click OK.
Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.
Right-click Unallocated or RAW volume, and select New Simple Volume.
In the New Partition Wizard, click Next.
Select Primary partition.
Leave the partition size set to default, and click Next.
Assign a drive letter or leave it set to the default, and click Next.
Enter the following settings to format the partition:
The new drive should appear in Windows Explorer.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).
Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.
Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.
To create a partition on a new drive, complete the following:
Open Finder.
Navigate to Applications and click Utilities.
Open Disk Utility.
Select the new drive and click the Partition tab.
Click Options and verify that it is set to GUID Partition Table.
Enter a name for the partition.
Click Partition.
The drive should now be accessible in Finder.