Product Zoeken

150 Mbps 1T1R draadloos-N access point voor buiten - 2,4 GHz 802.11b/g/n PoE-aangestuurd WiFi-AP

Creëer een krachtig draadloos N-netwerk op lange afstand vanaf een vaste netwerkverbinding - PoE-aangestuurd

Productcode: AP150WN1X1OE

  • Weerbestendige, op een paal en de muur te bevestigen behuizing
  • PoE-aangestuurd access point inclusief PoE-injector
  • Voldoet aan IEEE 802.11n (draadloos-N), met snelheden tot 150 Mbps databandbreedte
Uw prijs
€89,99 EUR excl. BTW
€108,89 EUR incl. BTW

Met het AP150WN1X1OE draadloze accesspoint kunt u buiten een 150 Mbps draadloos N-netwerk op lange afstand creëren via een vaste netwerkverbinding. Hierdoor voorziet u uw draadloze apparaten, zoals smartphones, tablets en laptops, van draadloze connectiviteit.

Dit PoE-aangestuurd access point wordt geleverd met een PoE-injector, waardoor het gemakkelijk kan worden geïnstalleerd op plaatsen waar geen gewone wandcontactdoos aanwezig is. Voor een veelzijdige installatie buiten kan de weerbestendige behuizing op een paal en op de muur worden gemonteerd.

Het access point beschikt over een interne 1T1R 12dBi directionele antenne met een aanpasbare uitgangssterkte voor de door u gewenste reikwijdte. Het toegangspunt beschikt ook over een optionele RP-SMA-verbinding, zodat u een externe antenne en een tweede LAN-poort kunt aanbrengen om, indien nodig, verbinding te maken met een extra vast netwerkapparaat.

Het krachtige draadloze access point ondersteunt draadloze gegevenssnelheden tot 150 Mbps op de 2,4 GHz frequentie, is compatibel met 802.11b/g/n-apparaten en biedt ondersteuning voor WEP-, WPA- en WPA2-authenticatie. Het draadloze toegangspunt beschikt over een gebruiksvriendelijke, op het web gebaseerde functie voor verschillende klantenspecifieke opties, zoals meervoudige SSID's, externe firmware upgrades en Wireless Distribution System (WDS)-modusondersteuning waardoor meerdere AP's kunnen worden samengevoegd voor een grotere reikwijdte.

Gedekt door een 2-jarige garantie en gratis levenslange technische ondersteuning van StarTech.com.

Toepassingen

  • Creëer buiten een draadloos-N AP vanaf een bestaande vaste verbinding om dode punten in het netwerk te verwijderen en om draadloze apparaten in grote open ruimtes met elkaar te verbinden.
  • Gebruik WDS (Wireless Distribution System) om meerdere access points samen te voegen

Het voordeel van StarTech.com

  • Bescherming tegen ruwe weersomstandigheden dankzij weerbestendige behuizing
  • Eenvoudige installatie met keuze tussen installatie op een paal of muur
  • Bereik een optimale draadloze reikwijdte met een optionele externe antenneconnector

Partnernummers

  • Ingram Micro Netherlands 2532875
  • UPC 065030853583

Specificaties

Warranty Information Warranty 2 Years
Connector(en) 1 - Interne poorten RP-SMA (coax, Reverse Polarity SubMiniature A)
2 - Interne poorten RJ-45
Fysieke eigenschappen Kleur Wit
Type behuizing Kunststof
Lengte product 29,2 cm [11,5 in]
Breedte product 92 mm [3,6 in]
Hoogte product 59 mm [2,3 in]
Gewicht product 345 g [12,2 oz]
Gebruiksomgeving Bedrijfstemperatuur 0°C to 70°C (32°F to 122°F)
Opslagtemperatuur -20°C to 70°C (-4°F to 158°F)
Vochtigheid 10% - 90% rel. luchtvochtigheid
Hardware Interface Draadloos
Antenneconfiguratie 1x1:1 (TxR:S)
Industriestandaarden IEEE 802.3, IEEE 802.3u
IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Chipsetcode Realtek - RTL8196C
Indicatoren 1 - LED-indicatoren PoE-koppeling/activiteit
Power
LAN-verbinding/activiteit
Draadloze verbinding/activiteit
Prestaties Maximale overdrachtsnelheid 150 Mbit/s
Bandbreedte 20/40 MHz
Frequentiebereik 2.400 ~ 2.484 GHz
Beveiligingsmogelijkheden TKIP/AES
WEP-encryptie
WPA and WPA2-PSK Data Encryption
WPA and WPA2 Enterprise Data Encryption
Ondersteunde protocollen CSMA/CA
Speciale opmerkingen / vereisten Systeem- en kabelvereisten Wisselstroomstopcontact binnen aanwezig
Cat 5 (of betere)-netwerkkabels van een PoE-injector naar een draadloos toegangspunt en PoE-injector naar LAN-schakelaar/router (niet meer dan 100 m in totaal)
Verpakkingsinformatie Package Height 93 mm [3,7 in]
Package Length 11,7 cm [4,6 in]
Package Width 33,5 cm [13,2 in]
Verpakkingsaantal 1
Verzendgewicht (verpakt) 692 g [24,4 oz]
Voeding Inclusief voedingsadapter Inclusief wisselstroomadapter
Ingangsspanning 100 - 240 AC
Ingangsstroom 0.3 A
Uitgangsspanning 12V DC
Uitgangsstroom 1 A
Polariteit pin midden Positief
Stekkertype M
Vermogensopname 12
Wat wordt er meegeleverd 1 - Meegeleverd Toegangspunt voor buiten
PoE-injector
Metalen slangklem
Voedingsadapter
Gebruiksaanwijzings-CD

Accessoires

SVA12M2NEUA

DC power adapter - 12V, 2A - voedingsadapter

Vervang uw zoekgeraakte of defecte voedingsadapter

Uw prijs
€25,99 EUR excl. BTW
€31,45 EUR incl. BTW
SVA12M5NA

DC power adapter - 12V, 5A - voedingsadapter

Vervang uw zoekgeraakte of defecte voedingsadapter

Uw prijs
€65,99 EUR excl. BTW
€79,85 EUR incl. BTW

Drivers/Downloads

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Firmware

Handleiding:

Datasheet

Productondersteuning

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Veelgestelde vragen (FAQ)

Installatie

The AP150WN1X1OD can be set up to create a wireless network for an existing wired network, which is called Access Point (AP) mode.

The following is required to set up the unit in AP mode:

  • A network infrastructure or network device that is TCP/IP compliant.
  • A computer with a wired Ethernet connection.
  • Two Ethernet patch cables.

If the unit is not brand new or there are previous settings saved on the unit, you need to complete a factory reset before you can proceed. For more information about factory resets, refer to the following FAQ: http://www.startech.com/faq/networking_ap150wn1x1od_factory_reset.

Connect the AP150WN1X1OD

To set up the unit, you need to connect the AP150WN1X1OD using a wired Ethernet cable.

  1. Remove the plastic panel from the bottom of the AP150WN1X1OD.
  2. Connect the power adapter to the POE injector.
  3. Connect an Ethernet cable to the POE injector and the AP150WN1X1OD. The AP150WN1X1OD should be receiving power. If it is not, move the Ethernet cable to the other port.
  4. Connect the Ethernet cable from the LAN port on the POE injector to your computer. 
  5. When you are done configuring the AP150WN1X1OD, reattach the plastic panel.

Wait 30 seconds for the unit to restart before you make any configuration changes.

Configure the software

To make changes to the configuration, you need to make sure that your computer is on the same network as the AP150WN1X1OD. By default, the access point assigns your computer an IP address that is on the 192.168.1.XXX network.

If you are having issues accessing the Wireless Access Point, you may need to manually set the IP address. For more information, refer to the following FAQ as appropriate for your operating system: How do I change my IP address in [your operating system]?

The default IP address of the access point is 192.168.1.200, which means that the computer needs to have an address similar to 192.168.1.[XXX], where [XXX] is a number between 1 and 255, but is not 200 (for example, 192.168.1.1).

Use the web configuration

Make sure that your computer is on the 192.168.1.XXX network and complete the following:

  1. Open a web browser.
  2. In the address bar, type http://192.168.1.200.
  3. In the username and password fields, type admin.
  4. Click the Start button at the bottom of the screen to begin the Setup Wizard.
  5. To turn on AP mode, complete the steps in the Setup Wizard. Make sure that you add your preference for wireless SSID (what the unit will be identified as over Wi-Fi), security, and password.

When the Setup Wizard is finished, do the following:

  1. If any modifications were made, set your computer back to the original IP configuration.
  2. Plug your wired network into the LAN port of the AP or POE injector.

Your AP150WN1X1OD will now host the wired network over Wi-Fi.

A Wireless Distribution System (WDS) allows you to use the Access Point (AP) to connect to other APs using a wireless signal. A WDS can create a seamless network between multiple WDS-compatible APs. A WDS can improve network connectivity over a larger geographical area, but the network speed is reduced up to 50% each time that you add a new AP to the WDS.

Note: Only IP-based networks can be used with a WDS.

Connect the hardware

To set up the unit, you need to connect the AP150WN1X1OD using a wired Ethernet connection.

  1. Use the provided power adapter to connect power to the POE injector.
  2. Connect an Ethernet cable between the PoE injector and the AP150WN1X1OD. The AP150WN1X1OD should be receiving power, but if it is not, move the Ethernet cable to the other port.
  3. Connect the Ethernet cable from the LAN port on the PoE injector to your computer system.

Wait 30 seconds for the unit to start before you make any configuration changes.

Prepare the site

The maximum range of the AP150WN1X1OD is 3 km, however, obstructions (such as buildings) may reduce the range. The AP150WN1X1OD can be used with multiple WDS-compatible APs (for example, additional AP150WN1X1OD devices) to overcome any physical barriers that may limit the Wi-Fi range.

To use multiple AP150WN1X1OD units to create a WDS, one unit needs to be assigned as the main AP and be connected to a wired network. The additional attached units need to be assigned as relay APs and be connected to the main AP.

Before you set up a WDS, you need the MAC address of all of the APs that you plan to use. The MAC address is located on a label on the back of the unit. The label has a barcode with text underneath it, showing MAC: 001AEF[xxxxxx]. Decide where you plan to locate the APs and write down the MAC address that correlates with each AP.

You also need to assign each AP a unique IP address that is on the same network as the wired network. For example, if the main network is 192.168.1.xxx and the default gateway is on 192.168.1.1, the APs need to be assigned static IP addresses from 192.168.1.[2-255]. Ideally, the IP addresses are outside of a DHCP server range to prevent IP address conflicts. This information can be obtained from the router on your network.

Although each AP that you use in your setup requires a unique MAC address, SSID, and IP address, the APs all need to have identical settings for the following:

  • Band (for example, 2.4 GHz (B+G+N))
  • Channel number (1 to 11)
  • DHCP set to Disabled
  • Subnet mask (for example, 255.255.255.0)
  • Default gateway

The following is an example of a setup list:

AP Location SSID MAC address IP address
Main Data center StarTech.com Guest 001AEF41687F 192.168.1.200
Relay 1 Upstairs StarTech.com Upstairs 001AEF416880 192.168.1.201
Relay 2 Downstairs StarTech.com Downstairs 001AEF416881 192.168.1.202

Note: You should assign each AP a unique SSID (Wi-Fi name) instead of using a common SSID.

Set up the main AP

The steps described below apply to firmware version 1.2f.05 and use the factory default settings.

  1. Use an Ethernet cable to connect the AP150WN1X1OD to a computer.
  2. Make sure that your computer is on the 192.168.1.xxx network.
  3. Open a web browser (for example, Internet Explorer).
  4. In the address bar, enter http://192.168.1.200.
  5. In the username field, enter admin.
  6. In the password field, enter admin.
  7. Click More Settings Wireless Settings WDS Settings.
  8. Under Wireless Network, enter the SSID of the main AP.
  9. Disable DHCP.
  10. Set the Channel Number, IP Address, Subnet Mask, and Default Gateway to the predetermined values.
  11. Enter the MAC address of the first relay AP.
  12. Add a comment that describes the location or SSID of the relay AP.
  13. Set the Band to the predetermined value.
  14. Click Apply and wait for the AP to restart.
  15. For each of the additional relay APs in your setup, repeat steps 11 to 14.
  16. If you want to encrypt the wireless network, click Set Security and fill out the form.

Note: If the IP address was changed to a different network, you will need to change the computer IP address to the network of the access point to make further changes.

Set up the relay APs

  1. Use an Ethernet cable to connect the AP150WN1X1OD to a computer.
  2. Make sure that your computer is on the 192.168.1.xxx network.
  3. Open a web browser (for example, Internet Explorer).
  4. In the address bar, enter http://192.168.1.200.
  5. In the username field, enter admin.
  6. In the password  field, enter admin.
  7. Click More Settings Wireless Settings > WDS Settings.
  8. Under Wireless Network, enter the SSID of the main AP.
  9. Disable DHCP.
  10. Set the Channel NumberIP AddressSubnet Mask, and Default Gateway to the predetermined values.
  11. Enter the MAC address of the main AP.
  12. Add a comment for the main AP.
  13. Set the Band to the predetermined value.
  14. Click Apply and wait for the unit to restart.
  15. For each of the additional relay APs in your setup, repeat steps 1 to 14.
  16. If you want to encrypt the wireless network, click Set Security and fill out the form.

When you are done setting up the main and relay APs, place the units where you want them and connect the wired LAN to the main AP. To confirm the connectivity of the relay AP, under WDS Settings, click Show Statistics.

Although the AP150WN1X1OD does not have an explicit repeater mode, multiple access points can be configured in a WDS (Wireless Distribution System) with the same SSID to create a seamless wireless network over a large geographical area.

You can set up the AP150WN1X1OD in a WDS to set up the repeater network and ensure that the same SSID and security settings are used for the main and relay access points. Relay access points can also be daisy chained with other relays by adding their MAC addresses to the WDS AP List of the primary relay access point. For more information about setting up your AP150WN1X1OD in a WDS, refer to the following FAQ: http://www.startech.com/faq/networking_ap150wn1x1od_wds_setup.

The following are some drawbacks to using the repeater setup:

  • If you use the same SSID as the main access point, some wireless devices may have to connect to lower power access points, which may cause issues with some wireless devices.
  • Every time that you add a relay access point, the network bandwidth is reduced by half.
  • Large geographical areas or obstructions can depreciate network integrity.

Note: Only IP-based networks can be used with a WDS.

Troubleshooting

This device's default static IP address is 192.168.1.200.

  1. Make sure that the AP150WN1X1OD is on the same network as your computer.
  2. In an Internet browser, enter the IP address of the unit. The default IP address is 192.168.1.1.
  3. In the user name field, enter the user name. The default user name is admin.
  4. In the password field, enter the password. The default password is admin.

Press and hold the reset button for 10 seconds.

U zou de firmware van uw apparaat niet moeten upgraden als u geen problemen hebt met de functionaliteit van uw apparaat. De enige keer dat u een upgrade zou moeten overwegen, is wanneer u een probleem met het apparaat hebt en u hebt bevestigd dat de firmware dit probleem kan oplossen.  U kunt dit bevestigen door de bij de firmware geleverde documentatie te raadplegen of contact op te nemen met ons Technisch Ondersteuningsteam. Een verkeerde upgrade van de firmware kan leiden tot verminderde prestaties. U kunt dus het best contact opnemen met StarTech.com als u dit wilt uitvoeren.

Hoe gaat u te werk

The AP150WN1X1OD features a directional antenna at the front of the unit (the front of the unit being the large open surface with the StarTech.com logo on it). The AP150WN1X1OD radiation pattern has a horizontal beam width of 30 degrees and a vertical beam width of 20 degrees.

For best results, you should position the AP150WN1X1OD towards the majority of wireless clients. Optimally, you should place the unit in a corner of a larger area, as opposed to the center. Connectivity can be improved when there is as few obstructions as possible, so you should use the AP150WN1X1OD in open areas.

To get more coverage in a larger geographical area, you can set up a WDS. A WDS works best when there is line-of-sight between the access points. For more information about WDS, refer to the following FAQ: http://www.startech.com/faq/networking_ap150wn1x1od_wds_setup.

Voor uw aanschaf

You cannot replace the function of a router with the AP150WN1X1OD. You need a router connected to a modem to access the Internet.

The AP150WN1X1OD can be used to create a wireless access point for a router, switch, or networking device that does not have wireless capabilities. When you use the AP150WN1X1OD to create a wireless access point, wireless devices can be connected to a wired device. To connect a wireless device to a wired device, connect the wired network connection to the LAN port on the POE injector (gray box) or on the LAN port of the unit.

For more information about how to set up an access point, refer to the following FAQ: http://www.startech.com/faq/networking_ap150wn1x1od_access_point_setup.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Uitvoering en specificaties van het product zijn zonder aankondiging vatbaar voor wijzigingen.
Wacht...
Terug naar boven