10/100 Ethernet to Multi Mode Fiber Media Converter SC 2 km

Verleng een 10/100 Mbit/s Ethernet-verbinding met 2 km via multimode SC glasvezel

Productcode: MCM110SC2GB

  • Supports a maximum multi mode fiber optic cable distance of 2 km
  • Compatible with most 3COM™, Cisco™, Lucent™ and Nortel™ networks
  • Supports transparent Q-in-Q double tagged frames
Uw prijs
€94,99 EUR excl. VAT
€114,94 EUR incl. VAT

The MCM110SC2GB 10/100 Multi Mode Fiber Ethernet Media Converter SC 2 km creates an economical, cost-effective Ethernet-fiber link, transparently converting to/from 10Base-T or 100Base-Tx Ethernet signals and 100Base-Fx optical signals to extend an Ethernet network connection over an SC terminated multimode fiber backbone.

The converter supports a maximum multimode fiber optic cable distance of 2 kilometers (1.2 miles), providing a simple solution for connecting 10Base-T/100Base-Tx Ethernet networks to remote locations using SC-terminated multimode fiber, while delivering solid network performance and scalability.

This versatile GbE Ethernet to Fiber converter is compatible with most 3COM™, Cisco™, Lucent™ and Nortel™ networks and fully complies with applicable IEEE 802.3 standards.

Backed by a StarTech.com 2-year warranty and free lifetime technical support.

Toepassingen

  • Extend your Ethernet connection up to 2km away using fiber optics
  • Designed for large, higher speed bandwidth that has a demanding work groups that require expansion of fast Ethernet Network
  • Connect via fiber optics two or more building on the same campus
  • Connect remote sub-networks to larger fiber optic networks/backbones

Het voordeel van StarTech.com

  • Improve network scalability by increasing the distances between network points by up to 2km (Multi-mode)
  • Compact, lightweight enclosure is easily mounted or placed into any location with little to no configuration needed
  • Provides increased bandwidth and high data throughput by eliminating network bottlenecks and congestion

Partnernummers

  • UPC 065030836524

Specificaties

Warranty Information Warranty 2 Years
Connector(en) 1 - Connectoren lokale eenheid RJ-45
1 - Aansluitingen externe eenheid Glasvezel SC duplex
Fysieke eigenschappen Kleur Zwart
Lengte product 95 mm [3,7 in]
Breedte product 75 mm [3,0 in]
Hoogte product 20 mm [0,8 in]
Gewicht product 90,5 g [3,2 oz]
Gebruiksomgeving Bedrijfstemperatuur 0°C to 50°C (32°F to 122°F)
Opslagtemperatuur -10°C to 70°C (14°F to 158°F)
Vochtigheid 10~90% RH
Hardware PoE Nee
WDM Nee
Industriestandaarden IEEE 802.3u 100BASE-FX
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
Indicatoren 1 - LED-indicatoren FEF [Far End Fault](On - Fault Detected, Off - No Fault
Ethernet Link & Activity (ON - Fiber Link ok, Blinking - Activity on Fiber Link)
Speed (10 or 100 Mbps)
Power
Full ( Full duplex / Half duplex)
Fiber Link & Activity (On - Fiber Link ok, Blinking - Activity on Fiber Link)
Prestaties Maximale overdrachtsnelheid 10/100Mbps
Max. overdrachtsafstand 2 km (1.2 mi)
Glasvezeltype Multi-Mode
Golflengte 1310nm
Glasvezelmodus Half/Full-Duplex
MTBF 65,000 Hours
Verpakkingsinformatie Package Length 17,5 cm [6,9 in]
Package Width 14,5 cm [5,7 in]
Package Height 65 mm [2,6 in]
Verzendgewicht (verpakt) 280 g [9,9 oz]
Voeding Inclusief voedingsadapter Inclusief wisselstroomadapter
Ingangsspanning 100 - 240 AC
Uitgangsspanning 12V DC
Uitgangsstroom 0.2A
Polariteit pin midden Positief
Stekkertype M
Vermogensopname 2.4
Wat wordt er meegeleverd 1 - Meegeleverd Media Converter
UK power plug
EU power plug
Power Adapter
User's Manual

Accessoires

SVA12M2NEUA

DC power adapter - 12V, 2A - voedingsadapter

Vervang uw zoekgeraakte of defecte voedingsadapter

Uw prijs
€25,99 EUR excl. VAT
€31,45 EUR incl. VAT
SVA12M5NA

DC power adapter - 12V, 5A - voedingsadapter

Vervang uw zoekgeraakte of defecte voedingsadapter

Uw prijs
€65,99 EUR excl. VAT
€79,85 EUR incl. VAT

Drivers/Downloads

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Handleiding:

Datasheet

Productondersteuning

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Veelgestelde vragen (FAQ)

Troubleshooting

When you troubleshoot issues with a fiber media converter, there are some quick tests that you can complete to rule out potential problems. To identify what the source of the issue is, observe the power LED, LAN LEDs, and fiber link LED on the units.

If the power LED is not illuminated for the transmitter or the receiver, complete the following:

  • Make sure that you are using the provided power adapter(s).

  • Make sure that the adapter is plugged into a compatible wall outlet.

  • Make sure that the adapter is plugged into both the transmitter and receiver.

If another LED is not operating as expected, make sure that the components in your setup are working correctly. To test your setup components, try the following:

  • Use the cables, fiber media converter, and network devices (including SFPs, if applicable) in another setup to see if the problem is with the components or the setup.

  • Use different cables, fiber media converter, and network devices (including SFPs, if applicable) in your setup to see if the problem persists. Ideally, you should test components that you know work in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.

  • Use short cables when you are testing.

Make sure that the DIP switches are set to the following:

  • DIP switches should be identical on both local and remote units. By default, DIP switches are set to Off (the switch is pointing up).

  • For more information about the advanced configuration options, refer to the manual for your product.

If you cannot establish a network connection between your local and remote units, you need to do the following to make sure that the issue is not related to the network configuration:

  • Use two computer systems directly connected to the fiber media converter LAN ports.

  • Open a command prompt on Computer 1 and ping Computer 2.

If the issue is not related to the network configuration, you should receive a response from Computer 2.

 

For more information on how to ping another network device, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=networking#ping-test-windows-mac-os.

Voor uw aanschaf

Different optical cables are needed for different applications. Before you select a cable to interconnect fiber devices, make sure that the following things match:

  • Mode: Single Mode or Multi Mode.

  • Wavelength: For example, 850 nm, 1310 nm, or 1550 nm.

Note: The above properties cannot be converted or changed by a cable.

When you select a cable, make sure that the cable ends (for example, LC, SC, ST, or MT) match the fiber media devices.

Simplex and duplex ends are available for most connector types. Simplex cables have the connectors separate, where duplex cables have the transmit (TX) and receive (RX) connectors joined together.  StarTech.com fiber media devices are compatible with simplex and duplex connectors.

It does not matter which diameter or OM classification the cable uses, as long as it meets the mode requirement.

Fiber media converters can be used to convert a standard Ethernet connection to a standard fiber connection, or can be used to extend a copper Ethernet network. When you use fiber media converters to extend a copper Ethernet network, make sure that the same fiber standards are being used on either end of the fiber network.

Note: Terms like 1000BASE-LX, 100BASE, 1000BASE, and 10GBASE refer to how fast the data can transfer, with 100BASE being 100Mb/s, 1000BASE being 1000Mb/s or 1GB/s, and 10GBASE being 10Gb/s. FX, SX, LX, and SR refer to different fiber standards and use different wavelengths (among other things).

Fiber media converters come in different types for different applications. You need to consider the specifications for both network devices before you can select the correct fiber media converters.

A fiber media converter can be used to simply convert fiber to copper (for example, 100BASE-FX to 100BASE-TX), convert copper to fiber, or it can be used to extend a copper network over fiber optic cabling. If you use an application that uses fiber media converters, the copper and fiber industry standards must match.

The following is an example of a working fiber to copper setup:

  • A network switch that has an LC fiber output using 1000BASE-LX is connected to an LC fiber cable that patches into the ET1000S40LC2, which is compatible with 1000BASE-LX/SX. The connected copper device is 1000BASE-T.

If the copper device in the above setup is 10/100 (100BASE-T), no copper link would be detected.

Note: Some media converters do not auto-negotiate copper or fiber standards, which limits the device to 10/100 or gigabit operation. For more information, check the specifications of the media converter.

When you use the fiber media converter in a network extender setup, it works best if you use the same media converter on either end. As long as the fiber standards match, you can use different connectors and the fiber network will be created between the units.

The following are some examples of available fiber connector types:

  • LC
  • SC
  • ST
  • Open SFP

The Open SFP units (referred to as Open on the Fiber Media Converter Drilldown) can use any mini-GBIC or SFP compatible fiber transceiver. The ET LC fiber media converters include LC SFPs, which makes the unit an open SFP, if required.

UPC and APC are fiber cable connector types. UPC (Ultra Physical Contact) connectors have a fiber connector end face that has been polished to be dome-shaped. This results in light that can be reflected straight back to the source.

APC (Angled Physical Contact) connectors have a fiber connector end face that has been polished at an eight degree angle. This results in a reduced amount of light that is reflected between the two connected fibers.

StarTech.com fiber cables use UPC connectors.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Uitvoering en specificaties van het product zijn zonder aankondiging vatbaar voor wijzigingen.
Terug naar boven
Wacht...