Productcode: MCM110ST2EU
De MCM110ST2EU 10/100 Multi-Mode ST Glasvezel Ethernet Converter (2 km) legt een voordelige verbinding van Ethernet naar glasvezel en zet 10Base-T of 100Base-Tx Ethernet-signalen transparant om van/naar 100Base-Fx optische signalen voor het uitbreiden van een Ethernet-netwerkverbinding via een multi-mode glasvezelbackbone.
De ST-glasvezelconverter ondersteunt een maximale multi-mode kabelafstand van 2 km en biedt een eenvoudige oplossing voor het verbinden van 10Base-T/100Base-TX Ethernet-netwerken met externe locaties via multimode ST-glasvezel, met goede netwerkprestaties en schaalbaarheid.
Deze compacte, voordelige Ethernet-glasvezelconverter is eenvoudig te installeren en ondersteunt auto-switching MDI en MDI-X op de RJ45 UTP-aansluitingen en handmatige bediening van UTP-modus, snelheid, full/half-duplex en LFP (Link Fault Pass-through).
Met 2 jaar garantie en gratis levenslange technische ondersteuning door StarTech.com.
Warranty Information | Warranty | 2 Years |
---|---|---|
Connector(en) | 1 - Connectoren lokale eenheid | RJ-45 |
Glasvezel ST duplex | ||
Fysieke eigenschappen | Kleur | Zwart |
Type behuizing | Kunststof | |
Lengte product | 75 mm [3,0 in] | |
Breedte product | 95 mm [3,7 in] | |
Hoogte product | 20 mm [0,8 in] | |
Gewicht product | 90,5 g [3,2 oz] | |
Gebruiksomgeving | Bedrijfstemperatuur | 0°C to 50°C (32°F to 122°F) |
Opslagtemperatuur | -10°C to 70°C (14°F to 158°F) | |
Vochtigheid | 10% - 90% rel. luchtvochtigheid | |
Hardware | PoE | Nee |
WDM | Nee | |
Industriestandaarden | IEEE 802.3u 100BASE-FX | |
IEEE 802.3 10BASE-T | ||
IEEE 802.3u 100BASE-TX | ||
Indicatoren | 1 - LED-indicatoren | FEF [Far End Fault] (aan - fout gedetecteerd, uit - geen fout) |
Ethernet verbinding en activiteit (aan - glasvezelverbinding ok, knipperend - activiteit op glasvezelverbinding) | ||
Snelheid (10 of 100 Mbit/s) | ||
Power | ||
Full (full-duplex / half-duplex) | ||
Glasvezel verbinding en activiteit (aan - glasvezelverbinding ok, knipperend - activiteit op glasvezelverbinding) | ||
Prestaties | Maximale overdrachtsnelheid | 10/100 Mbit/s |
Max. overdrachtsafstand | 2 km (1.2 mi) | |
Glasvezeltype | Multi-Mode | |
Golflengte | 1310nm | |
Glasvezelmodus | Half/Full-Duplex | |
Optisch vermogen | -14 ~ -20 dBm | |
Gevoeligheid | -31 dBm | |
Energiebudget | 11 dB | |
MTBF | 65,000 Hours | |
Verpakkingsinformatie | Package Length | 14,5 cm [5,7 in] |
Package Width | 17,5 cm [6,9 in] | |
Package Height | 65 mm [2,6 in] | |
Verzendgewicht (verpakt) | 280 g [9,9 oz] | |
Voeding | Inclusief voedingsadapter | Inclusief wisselstroomadapter |
Ingangsspanning | 100 - 240 AC | |
Uitgangsspanning | 12V DC | |
Uitgangsstroom | 0.2A | |
Polariteit pin midden | Positief | |
Stekkertype | M | |
Vermogensopname | 2.4 | |
Wat wordt er meegeleverd | 1 - Meegeleverd | Glasvezel Converter |
Voedingsadapter | ||
Handleiding |
Vervang uw zoekgeraakte of defecte voedingsadapter
Vervang uw zoekgeraakte of defecte voedingsadapter
Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)Wij staan altijd klaar om al uw vragen te beantwoorden.
Chat Live (opens in new window)When you troubleshoot issues with a fiber media converter, there are some quick tests that you can complete to rule out potential problems. To identify what the source of the issue is, observe the power LED, LAN LEDs, and fiber link LED on the units.
If the power LED is not illuminated for the transmitter or the receiver, complete the following:
Make sure that you are using the provided power adapter(s).
Make sure that the adapter is plugged into a compatible wall outlet.
Make sure that the adapter is plugged into both the transmitter and receiver.
If another LED is not operating as expected, make sure that the components in your setup are working correctly. To test your setup components, try the following:
Use the cables, fiber media converter, and network devices (including SFPs, if applicable) in another setup to see if the problem is with the components or the setup.
Use different cables, fiber media converter, and network devices (including SFPs, if applicable) in your setup to see if the problem persists. Ideally, you should test components that you know work in another setup.
When you test your cables, it is recommended that you do the following:
Test each cable individually.
Use short cables when you are testing.
Make sure that the DIP switches are set to the following:
DIP switches should be identical on both local and remote units. By default, DIP switches are set to Off (the switch is pointing up).
For more information about the advanced configuration options, refer to the manual for your product.
If you cannot establish a network connection between your local and remote units, you need to do the following to make sure that the issue is not related to the network configuration:
Use two computer systems directly connected to the fiber media converter LAN ports.
Open a command prompt on Computer 1 and ping Computer 2.
If the issue is not related to the network configuration, you should receive a response from Computer 2.
For more information on how to ping another network device, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=networking#ping-test-windows-mac-os.
Different optical cables are needed for different applications. Before you select a cable to interconnect fiber devices, make sure that the following things match:
Mode: Single Mode or Multi Mode.
Wavelength: For example, 850 nm, 1310 nm, or 1550 nm.
Note: The above properties cannot be converted or changed by a cable.
When you select a cable, make sure that the cable ends (for example, LC, SC, ST, or MT) match the fiber media devices.
Simplex and duplex ends are available for most connector types. Simplex cables have the connectors separate, where duplex cables have the transmit (TX) and receive (RX) connectors joined together. StarTech.com fiber media devices are compatible with simplex and duplex connectors.
It does not matter which diameter or OM classification the cable uses, as long as it meets the mode requirement.
Fiber media converters can be used to convert a standard Ethernet connection to a standard fiber connection, or can be used to extend a copper Ethernet network. When you use fiber media converters to extend a copper Ethernet network, make sure that the same fiber standards are being used on either end of the fiber network.
UPC and APC are fiber cable connector types. UPC (Ultra Physical Contact) connectors have a fiber connector end face that has been polished to be dome-shaped. This results in light that can be reflected straight back to the source.
APC (Angled Physical Contact) connectors have a fiber connector end face that has been polished at an eight degree angle. This results in a reduced amount of light that is reflected between the two connected fibers.
StarTech.com fiber cables use UPC connectors.