Niet meer leverbaar

2-poort PCI Express Interne SATA II Controller-kaart

Voeg 2 interne SATA 2.0 poorten toe aan uw desktopcomputer via een PCI Express uitbreidingsslot

Productcode: PEXSATA22I

  • 2 interne SATA-poorten
  • 48-bits Logical Block Addressing (LBA)
  • Boot-ROM-functionaliteit

Deze 2-poort PCI Express interne Serial ATA controller-kaart voegt twee interne SATA II (SATA300)-poorten toe aan een computer via een eenvoudige installatie in een beschikbare 1x PCI Express slot.

De SATA-controller kaart biedt ondersteuning voor overdrachtsnelheden tot 3 Gbit/s en beschikt over port multiplier-functionaliteit met command-based switching en Native Command Queuing voor optimale prestaties.

De interne SATA controller-kaart beschikt over een native PCI Express-chipset, die zorgt voor een verbeterde compatibiliteit, betrouwbaarheid en prestatie van opslagmedia. De controller-kaart is ook voorzien van port-multiplier functionaliteit met command-based switching voor het aansluiten van meerdere harde schijven op een computer via een enkele SATA-aansluiting.

De controller-kaart wordt geleverd met brackets voor zowel een standaard als low profile vormfactor, zodat u SATA-capaciteit kunt toevoegen aan vrijwel elke op PCI Express gebaseerde computer, ongeacht de vormfactor.

Toepassingen

  • Voeg interne SATA -functionaliteit toe aan een werkstation of server voor opslagmedia met hoge snelheid
  • Upgrade van tragere externe verbindingsmethoden naar native SATA-connectiviteit
  • Breid de opslagcapaciteit uit van een standaard of low profile computer met kleine vormfactor (SFF)

Het voordeel van StarTech.com

  • Voegt twee interne SATA-poorten met een snelheid tot 3 Gbps voor vol of laag profiel computersystemen
  • Ondersteunt harde schijven groter dan 136 GB met 48-bits LBA en gebruikt een enkele native PCI Express-chipset in plaats van een bridge chip om een snelle en betrouwbare werking zeker te stellen
  • Met levenslange garantie en gratis technische ondersteuning door StarTech.com

Partnernummers

  • Ingram Micro Netherlands 1597206
  • UPC 065030828000

Compatibility

  • Windows 8 logo
  • Linux logo
  • Windows Server 2012 logo
Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista (32/64), XP (32/64), 2000
Windows® Server 2012, 2008 R2, 2003
Linux

Specificaties

Warranty Information Warranty Lifetime
Connector(en) Type connector(en) 1 - PCI Express x1
Interne poorten 2 - SATA (7-polig, data)
Fysieke eigenschappen Lengte product 10,2 cm [4,0 in]
Breedte product 120 mm [4,7 in]
Hoogte product 2 cm [0,8 in]
Gewicht product 44,2 g [1,6 oz]
Hardware Poorten 2
Interface SATA
Bus type PCI Express
Kaarttype Standaard bracket (incl. low profile bracket)
Chipsetcode JMicron - JMB363
Prestaties Maximale overdrachtsnelheid 3 Gbit/s
Type en snelheid SATA II (3 Gbps)
Port-multiplier Nee
RAID Ja
Ondersteunde RAID-niveaus JBOD - (Just a Bunch of Disks)
RAID 0 (stripe)
RAID 1 (mirror)
Software Besturingssystemen Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista (32/64), XP (32/64), 2000
Windows® Server 2012, 2008 R2, 2003
Linux
Speciale opmerkingen / vereisten Notitie Voldoet aan 2.0 / compatibel met 2.0-slots voor PCI Express
Verpakkingsinformatie Package Length 20,8 cm [8,2 in]
Package Width 4,1 cm [1,6 in]
Package Height 144 mm [5,7 in]
Verzendgewicht (verpakt) 0,1 kg [0,3 lb]
Wat wordt er meegeleverd Meegeleverd 1 - PCI Express SATA-kaart
1 - Low-profile bracket
1 - Driver-CD
1 - Handleiding

Accessoires

SATA18

45 cm SATA Serial ATA Kabel

Deze hoogwaardige SATA-kabel is ontworpen voor het aansluiten van SATA-schijven zelfs in kleine ruimtes.

Uw prijs
€2,99 EUR excl. VAT
€3,62 EUR incl. VAT
SATA24

60cm SATA Serial ATA Kabel

Deze hoogwaardige SATA-kabel is ontworpen voor het aansluiten van SATA-schijven zelfs in kleine ruimtes.

Uw prijs
€3,99 EUR excl. VAT
€4,83 EUR incl. VAT
SATA36

90 cm SATA Serial ATA Kabel

Verbind en monteer SATA-schijven op eenvoudige wijze – ontworpen voor grotere behuizingen

Uw prijs
€2,99 EUR excl. VAT
€3,62 EUR incl. VAT

Drivers/Downloads

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Drivers:

Handleiding:

Datasheet

Productondersteuning

Praat met een adviseur.

Wij staan altijd klaar om al uw vragen te beantwoorden.

Chat Live (opens in new window)

Veelgestelde vragen (FAQ)

Hoe gaat u te werk

To confirm that Windows detects your expansion card, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Installatie

Before you install the device, make sure that your operating system is current (for example, the most recent service pack is installed).

  1. Download the latest drivers from the StarTech.com website at http://www.startech.com/Support. The part number and product ID are on the product packaging.

Note: Windows usually saves the files to the Downloads folder that is associated with your user account (for example, C:\Users\your_name\Downloads).

  1. After the download is complete, right-click the zip folder that you downloaded, click Extract All, and complete the instructions.
  2. In the list of extracted files, right-click the Setup.exe file and click Run as Administrator.

Note: If the Run as Administrator option is not available, you might be attempting to run the installer from within the zipped file. Extract the files using the instructions in step 2.

  1. Complete the instructions to install the device drivers, and restart your computer when prompted to.

Your computer will automatically complete the driver installation and your device should be ready to use.

Before you install the device, make sure that your operating system is current (for example, the most recent service pack is installed).

  1. Download the latest drivers from the StarTech.com website  at http://www.startech.com/Support. The part number and product ID are on the product packaging.

Note: Windows usually saves the files to the Downloads folder that is associated with your user account (for example, C:\Documents and Settings\your_name\My Documents\Downloads).

  1. After the download is complete, right-click the zip folder that you downloaded, click Extract All, and complete the instructions.
  2. In the list of extracted files, double-click the Setup.exe file.
  3. Complete the instructions to install the device drivers, and restart your computer when prompted to.

Your computer will automatically complete the driver installation and your device should be ready to use.

Troubleshooting

When you troubleshoot issues with a hard drive controller card, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables

  • Hard drives

  • Hard drive controller card

To test your setup components, try the following:

  • Use the IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in another setup to see if the problem is with the components or the setup.

  • Use a different IDE, SATA, or eSATA cable, hard drive, and hard drive controller card in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.

  • Use short cables when you are testing.

When you test the hard drive and hard drive controller card, it is recommended that you do the following:

  1. To open the Device Manager, press the Windows key + R, type devmgmt.msc, and press Enter. Check the IDE ATA/ATAPI controllers (for IDE) section, or the Storage controllers (for SATA) section.

  2. Do one of the following:

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.

  2. If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive does not show up in Computer or My Computer until it has a drive letter assigned to it.

In order to rebuild a RAID array, you need to replace a physical drive with an identical drive on the same RAID controller. Although standard RAID levels are generally agreed upon throughout the industry, the implementation varies between manufacturers. RAID arrays are typically not accessible when they are moved to another controller, and data may be unrecoverable if the drives are out of order or have been formatted or accessed by another RAID controller.

If a RAID controller has failed, you should get the exact same model of RAID controller.  

Note: If a drive or drives were damaged, it is possible that the RAID array may be permanently unrecoverable.

RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, you should back up the data on another physical drive or logical set of drives.

Rebuild a RAID array

With the following RAID modes, recovery is possible using the same StarTech.com product. Refer to the following table for the appropriate method to use to recover your RAID array.

RAID mode Max # of failed drives Procedure
RAID 1 Only one drive is needed for recovery.
  1. Determine which drive is operational by using the RAID management utility (if available) or test each drive individually on a different hard drive controller (for example, a hard drive docking station or SATA controller).

  2. Replace the failed drive with an identical hard drive.

The array will rebuild and is accessible during the rebuilding process.

RAID 3 Single drive failure will rebuild.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

RAID 5 Single drive failure will rebuild.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

RAID 10 Only one drive in a mirrored set can fail.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

 

Voor uw aanschaf

Although you can adapt a Serial Attached SCSI (SAS) drive to connect to a standard SATA controller card, the card must support SAS commands in order to communicate with SAS drives. SAS drives have a different command set that is not present on SATA controllers.

This SATA controller card only supports standard SATA drives.

Note: Not all StarTech.com devices support each of the RAID modes described below. For more information on the RAID modes that your device supports, refer to the manual or the StarTech.com product page.

Redundant Array of Independent Disks (RAID) is a virtual disk technology that combines multiple physical drives into one unit. RAID can create redundancy, improve performance, or do both.

RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, it should be backed up to another physical drive or logical set of drives.

The following are terms that are normally used in connection with RAID:

  • Striping: data is split between multiple disks.
  • Mirroring: data is mirrored between multiple disks.
  • Parity: also referred to as a checksum. Parity is a calculated value used to mathematically rebuild data.

Different RAID levels exist for different application requirements.

Refer to the following table for the list of RAID modes offered by some StarTech.com products:

RAID mode Description Operation Advantages Disadvantages Recovery
RAID 0 Striped disks Data is split evenly between two or more disks. Large size and the fastest speed. No redundancy. If one or more drives fails, this results in array failure.
RAID 1 Mirrored disks Two or more drives have identical data on them. A single drive failure will not result in data loss. Speed and size is limited by the slowest and smallest disk. Only one drive is needed for recovery.
RAID 3 Striped set with dedicated parity Data is split evenly between two or more disks, plus a dedicated drive for parity storage. High speeds for sequential read/write operations. Poor performance for multiple simultaneous instructions. A single drive failure will rebuild.
RAID 5 Striped disks with distributed parity Data is split evenly between three or more disks. Parity is split between disks. Large size, fast speed, and redundancy. The total array size is reduced by parity. A single drive failure will rebuild.
RAID 10 1+0; Striped set of Mirrored Subset Four or more drives are made into two mirrors that are striped. Larger size and higher speed than RAID-1, and more redundancy than RAID-0. No parity. Only one drive in a mirrored set can fail.
JBOD Just a Bunch Of Disks Any number of drives are accessed independently by the operating system. Software RAID modes can be used. Hardware RAID may have better performance. N/A
Big Spanning or Concatenation Data is written on one drive until it is full, and then the next drive(s) until it or they are full. Creates a very large and simple array.

No redundancy.

N/A
Clone RAID 1 + Spare

Two drives have identical data, plus one drive is used for rebuilding in case of a primary array failure.

Seamless operation when one drive fails in a RAID-1 array. Spare drive is not accessible to the user. Only one drive is needed for recovery.

 

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Uitvoering en specificaties van het product zijn zonder aankondiging vatbaar voor wijzigingen.
Terug naar boven