StarTech.com

Hårddiskkabinett med dubbla fack för M.2 SATA SSD-enheter - USB 3.1 (10 Gbps) - RAID

Gör om två M.2 SATA-hårddiskar till supersnabb, bärbar lagring med RAID för ökad prestanda eller redundans

Produkt ID: SM22BU31C3R

  • Maximera prestandan på dina M.2 SATA-hårddiskar (NGFF) med USB 3.1 Gen 2-anslutning (10 Gbps)
  • Stöder RAID 0, RAID 1, JBOD och SPAN (BIG) för optimal prestanda, kapacitet och redundans
  • Stöder alla vanliga M.2 SATA SSD-enheter och låter dig montera flera hårddisklängder: 30 mm (2230), 42 mm (2242), 60 mm (2260) en 80 mm (2280)
Visa mer
  • Ej kompatibel med M.2 NVMe eller AHCI PCI-Express SSD-enheter
  • Lägg till snabb och bärbar lagring till din bärbara dator, surfplatta, smarttelefon eller stationära dator med USB-C eller USB-A
  • Stöder SSD TRIM för ökad livslängd och prestanda
  • Kabinett i solitt aluminium med stöd för SATA I, II, III (upp till 6 Gbps)
  • Kompatibel med Thunderbolt 3 USB-C-port
  • Bakåtkompatibel med USB Gen 1 (USB 3.0), USB 2.0, USB 1.x
80,99 € EUR exkl. moms
101,24 € EUR inkl. moms
Inte tillgängligt
Kan finnas hos partners
Var kan jag köpa
Från en partner

Besök vår europeiska online-butik idag för fler produkter som denna!

Överblick

Detta dubbla M.2 SATA-kabinett med RAID gör det enkelt att lägga till supersnabb, bärbar extern lagring till din bärbara dator, surfplatta, smarttelefon eller stationära dator med USB-C™ eller USB-A. Dess multipla RAID-lägen ger ökad kapacitet, förbättrad prestanda eller dataredundans.

Nå din externa data med högre hastighet

Få åtkomst till, för över och säkerhetskopiera dina filer snabbt var du än är. Med detta M.2 RAID-kabinett med dubbla fack får du enkel åtkomst till din data genom att skapa en högpresterande, superbärbar lagringslösning med två M.2 SATA SSD-enheter (NGFF). Det är idealiskt för kreativa proffs, som till exempel fotografer och videografer samt proffs inom företag, utbildning och myndigheter som behöver snabb åtkomst till viktiga datafiler, ute på fält eller på kontoret.

Med RAID-kabinettet kan du utnyttja hastigheten från dina M.2 SATA-hårddiskar (NGFF) genom att utnyttja USB 3.1 Gen 2 med dataöverföringshastigheter på upp till 10 Gbps. Det garanterar enkel åtkomst till dina filer för datamigrering och säkerhetskopiering så att du hela tiden kan säkra viktig data.

Öka prestanda och dataredundans

Med flera RAID-alternativ ger M.2 RAID-kabinettet dig ökad lagringsstorlek, prestanda, eller redundans. Njut av sinnesro och vetskapen att dina filer hela tiden säkerhetskopieras eller utnyttja den högre hastigheten och kapaciteten med en kombinerad lösning. Kabinettet stöder RAID 0, RAID 1, Spanning och JBOD, så att du kan välja det säkerhetskopieringsläge du föredrar. Det stöder även SSD TRIM för ökad livslängd och prestanda.

Gör din data mer bärbar

Det dubbla M.2 SATA-kabinettet ger en väldigt bärbar lagringslösning. Med sin kompakta design kan du stoppa ner den i datorväskan och ta med den var som helst - till kontoret, labbet eller för mobil användning, så att du kan nå din data var du än är. M.2 SATA.kabinettet med dubbla fack är tillverkat med ett hölje i solitt aluminium för att skydda din data var du än är.

M.2 SATA RAID-kabinettet strömförses direkt från USB-porten på din enhet så att extern ström inte behövs. Den levereras med två USB-kablar (USB-C till Micro-B och USB-A till Micro-B) för flexibel användning med de senaste bärbara datorerna och surfplattorna med en USB-Type C™-port samt äldre enheter. Kabinettet är oberoende av OS utan att installation av extra program eller drivrutiner behövs och det är även kompatibelt med en Thunderbolt™ 3 USB-C-port. 

 SM22BU31C3R levereras med alla installationsverktyg som behövs och täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

Proffs inom många olika branscher, från företag till medicin, kan utnyttja den snabba dataåtkomsten för sin USB-C- eller USB-A-kapabla bärbara dator, surfplatta, smarttelefon eller stationära dator

Mobila proffs kan använda två M.2 (NGFF) SATA SSD-enheter för att få åtkomst till, föra över och säkerhetskopiera filer snabbare över USB 3.1 Gen 2 (10 Gbps)

Återanvänd eller få ny användning av M.2 SATA-hårddiskar för att få mer PC-lagring eller för att säkerhetskopiera data

Idealisk för att skydda hårddiskar mot damm och andra potentiella faror

Få åtkomst till hårddiskar för dataåterställning, säkerhetskopiering eller reparation

Tekniska specifikationer

Information om garanti
Garanti 2 Years
Hårdvara
Antal enheter 2
Busstyp USB 3.1 Gen 2
Chipset-ID ASMedia - ASM1352R
Enhetsinstallation Fixerad
Enhetsstorlek 22mm - M.2 SATA
Enhetstyp M.2 SATA (NGFF, B-Key)
Fläkt(ar) Nej
Gränssnitt USB 3.1 Gen 2
Stödda enhetshöjd(er) 2230
2242
2260
2280
Prestanda
4Kn Support Ja
Allmänna specifikationer Ej kompatibel med M.2 NVMe eller AHCI PCI-Express SSD-enheter
Maximal dataöverföringshastighet 10 Gbps
Maximal enhetskapacitet 2 TB
Medeltid mellan fel (MTBF) 35 000
Port Multiplier Ja
RAID Ja
RAID-lägen som stöds RAID 0 (stripade enheter)
RAID 1 (speglade enheter)
BIG (Omfång eller sammanfogning)
JBOD - (Just a Bunch of Disks)
TRIM Support Ja
Typ och hastighet USB 3.1 Gen 2 - 10 Gbit/s
SATA III (6 Gbps)
UASP-stöd Ja
Kontakt(er)
Enhetskontakter 2 - M.2 SATA (67 pin, NGFF) Slot Honuttag
Värdkontakter 1 - USB 3.1 USB type Micro-B (10-stifts, Gen 2, 10 Gbps) Hane
Mjukvara
OS-kompatibilitet OS independent; No software or drivers required
Indikatorer
LED-indikatorer 2 - Läsa/skriva (grön)
2 - Fel/ombyggt (röd)
Ström
Power Source Strömförsörjd via USB
Miljö
Drifttemperatur 0°C to 60°C (32°F to 140°F)
Förvaringstemperatur -20°C to 70°C (-4°F to 158°F)
Luftfuktighet 0% ~ 90% RH
Utseende
Färg Svart
Kabinettyp Aluminium
Maximal enhetshöjd 80 mm [3.1 in]
Produktbredd 80 mm [3.1 in]
Produkthöjd 15 mm [0.6 in]
Produktlängd 100 mm [3.9 in]
Produktvikt 96 g [3.4 oz]
Förpackning
Fraktvikt (förpackning) 195 g [6.9 oz]
Vad det är i lådan
Ingår i paketet 1 - M.2 SATA-kabinett
1 - USB-C till Micro-B-kabel - 46 cm
1 - USB-A till Micro-B-kabel - 46 cm
2 - monteringsskruvar för hölje
2 - paket med M.2-monteringsutrustning
1 - Skruvmejsel
1 - snabbstartsguide

Kompatibilitet

Se alla kompatibla operativsystem
OS independent; No software or drivers required

Certifikat

Relaterade produkter

USB 3.1 (10 Gbps) mSATA-hårddiskkabinett - aluminium
SMS1BMU313
USB 3.1 (10 Gbps) mSATA-hårddiskkabinett - aluminium

Gör om din mSATA- eller mSATA Mini-hårddisk till en bärbar, högpresterande lagringslösning över USB 3.1 Gen 2

44,99 € exkl. moms
56,24 € inkl. moms
M.2 till SATA SSD-kabinett - USB 3.1 (10 Gbps) med USB-C-kabel - externt kabinett
SM21BMU31C3
M.2 till SATA SSD-kabinett - USB 3.1 (10 Gbps) med USB-C-kabel - externt kabinett

Gör om din M.2 SATA-hårddisk till en supersnabb, superbärbar lagringslösning för USB-C-kapabla enheter

45,99 € exkl. moms
57,49 € inkl. moms
Hårddiskkabinett med dubbla fack för M.2 SATA SSD-enheter - USB 3.1 (10 Gbps) - RAID
SM22BU31C3R
Hårddiskkabinett med dubbla fack för M.2 SATA SSD-enheter - USB 3.1 (10 Gbps) - RAID

Gör om två M.2 SATA-hårddiskar till supersnabb, bärbar lagring med RAID för ökad prestanda eller redundans

80,99 € exkl. moms
101,24 € inkl. moms
M.2 till SATA SSD-kabinett - USB 3.0 med UASP - externt kabinett
SM2NGFFMBU33
M.2 till SATA SSD-kabinett - USB 3.0 med UASP - externt kabinett

Gör om din SSD-enhet till en ultraportabel fickenhet

39,99 € exkl. moms
49,99 € inkl. moms
Externt USB 3.1-kabinett (10 Gbps) för två 2,5
S252BU313R
Externt USB 3.1-kabinett (10 Gbps) för två 2,5" SATA-enheter

Gör om två 2,5" SATA SSD- eller HDD-enheter till högpresterande lagring med RAID - för USB-C- och USB-A-kapabla enheter

136,99 € exkl. moms
171,24 € inkl. moms
USB 3.1-kabinett (10 Gbps) för 2,5
S251BMU313
USB 3.1-kabinett (10 Gbps) för 2,5" SATA-enheter

Gör dig redo för supersnabb USB 3.1 Gen 2-datalagring med din 2,5" SSD eller HDD

43,99 € exkl. moms
54,99 € inkl. moms
Verktygslöst USB 3.1-kabinett (10 Gbps) för 2,5
S251BPU31C3
Verktygslöst USB 3.1-kabinett (10 Gbps) för 2,5" SATA SSD/HDD - USB-C

Lägg till snabb och bärbar datalagring till din USB Type-C-kapabla MacBook, ChromeBook Pixel eller bärbara dator

41,99 € exkl. moms
52,49 € inkl. moms
USB 3.1 (10 Gbps) 2,5
S251BU31C3CB
USB 3.1 (10 Gbps) 2,5" SATA SSD/HDD-kabinett med inbyggd USB-C-kabel

Skapa en snabb och bärbar datalagringslösning för din USB Type-C-kapabla bärbara dator

50,99 € exkl. moms
63,74 € inkl. moms
Verktygslöst USB 3.1-kabinett (10 Gbps) för 2,5
S251BPU313
Verktygslöst USB 3.1-kabinett (10 Gbps) för 2,5" SATA-enheter

Få högre hastighet med USB 3.1 Gen 2 i en lätt och bärbar lösning

36,99 € exkl. moms
46,24 € inkl. moms
USB 3.1-kabinett (10 Gbps) för 3,5
S351BU313
USB 3.1-kabinett (10 Gbps) för 3,5" SATA-enheter

Lösningen för datalagring med hög hastighet och hög kapacitet som du har väntat på - med USB 3.1 Gen 2

73,99 € exkl. moms
92,49 € inkl. moms

Tillbehör

Produktsupport

Vanliga frågor

Before You Buy

To determine if your hard drive will work in this enclosure, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the enclosure supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the enclosure was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the enclosure. For example, IDE, SATA, or M.2.
  • Make sure that the enclosure supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Make sure that the enclosure supports the height of your hard drive. For example, 9 mm or 15 mm.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the enclosure. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the enclosure.

Note: Not all StarTech.com devices support each of the RAID modes described below. For more information on the RAID modes that your device supports, refer to the manual or the StarTech.com product page.

Redundant Array of Independent Disks (RAID) is a virtual disk technology that combines multiple physical drives into one unit. RAID can create redundancy, improve performance, or do both.

RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, it should be backed up to another physical drive or logical set of drives.

The following are terms that are normally used in connection with RAID:

  • Striping: data is split between multiple disks.
  • Mirroring: data is mirrored between multiple disks.
  • Parity: also referred to as a checksum. Parity is a calculated value used to mathematically rebuild data.

Different RAID levels exist for different application requirements.

Refer to the following table for the list of RAID modes offered by some StarTech.com products:

RAID mode Description Operation Advantages Disadvantages Recovery
RAID 0 Striped disks Data is split evenly between two or more disks. Large size and the fastest speed. No redundancy. If one or more drives fails, this results in array failure.
RAID 1 Mirrored disks Two or more drives have identical data on them. A single drive failure will not result in data loss. Speed and size is limited by the slowest and smallest disk. Only one drive is needed for recovery.
RAID 3 Striped set with dedicated parity Data is split evenly between two or more disks, plus a dedicated drive for parity storage. High speeds for sequential read/write operations. Poor performance for multiple simultaneous instructions. A single drive failure will rebuild.
RAID 5 Striped disks with distributed parity Data is split evenly between three or more disks. Parity is split between disks. Large size, fast speed, and redundancy. The total array size is reduced by parity. A single drive failure will rebuild.
RAID 10 1+0; Striped set of Mirrored Subset Four or more drives are made into two mirrors that are striped. Larger size and higher speed than RAID-1, and more redundancy than RAID-0. No parity. Only one drive in a mirrored set can fail.
JBOD Just a Bunch Of Disks Any number of drives are accessed independently by the operating system. Software RAID modes can be used. Hardware RAID may have better performance. N/A
Big Spanning or Concatenation Data is written on one drive until it is full, and then the next drive(s) until it or they are full. Creates a very large and simple array.

No redundancy.

N/A
Clone RAID 1 + Spare

Two drives have identical data, plus one drive is used for rebuilding in case of a primary array failure.

Seamless operation when one drive fails in a RAID-1 array. Spare drive is not accessible to the user. Only one drive is needed for recovery.

 

USB 3.1 is the most recent version of the USB (Universal Serial Bus) standard for connecting computers and electronic devices. It is capable of data transfer speeds up to 10Gbps, and while it can use the USB-C connector type, it can also use a variety of other connector types. To achieve USB 3.1 transfer speeds, your USB host connection, cables, and device must all support USB 3.1. USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). 

USB 3.0 is capable of data transfer speeds up to 5Gbps. USB 3.0 is also known as USB 3.1 Gen 1 (5Gbps).

USB 3.1 is backwards compatible with USB 3.0 and USB 2.0, except in the following scenarios:

  • USB-B 3.1 cables are not compatible with USB-B 2.0 ports.
  • Unless you use an adapter, USB-C ports or cables will not work with USB-A or USB-B ports or cables.
  • Devices that require USB 3.1 transfer speeds of 10Gbps might not work with USB 3.0 or USB 2.0, or you might experience lower transfer speeds and impacted performance.
  • Bus-powered USB devices that requires more power than what USB 2.0 can provide are not compatible with USB 2.0.

To transfer data at speeds of 10Gbps, you need to confirm that the following components in your setup support USB 3.1:

  • The USB host connection
  • The USB cable
  • The USB device and any subcomponents (for example, a hard drive docking station and the hard drives in the docking station)

Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.

The included USB cable for this USB 3.1 Gen 2 device has been tested and verified to perform at USB 3.1 Gen 2 speeds of 10Gbps.

Problemsökning

When you troubleshoot issues with a hard drive enclosure, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Cables
  • Hard drives
  • Hard drive enclosure

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive enclosure in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive enclosure in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive enclosure, it is recommended that you do the following:

  • To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.​

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

In order to rebuild a RAID array, you need to replace a physical drive with an identical drive on the same RAID controller. Although standard RAID levels are generally agreed upon throughout the industry, the implementation varies between manufacturers. RAID arrays are typically not accessible when they are moved to another controller, and data may be unrecoverable if the drives are out of order or have been formatted or accessed by another RAID controller.

If a RAID controller has failed, you should get the exact same model of RAID controller.  

Note: If a drive or drives were damaged, it is possible that the RAID array may be permanently unrecoverable.

RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, you should back up the data on another physical drive or logical set of drives.

Rebuild a RAID array

With the following RAID modes, recovery is possible using the same StarTech.com product. Refer to the following table for the appropriate method to use to recover your RAID array.

RAID mode Max # of failed drives Procedure
RAID 1 Only one drive is needed for recovery.
  1. Determine which drive is operational by using the RAID management utility (if available) or test each drive individually on a different hard drive controller (for example, a hard drive docking station or SATA controller).

  2. Replace the failed drive with an identical hard drive.

The array will rebuild and is accessible during the rebuilding process.

RAID 3 Single drive failure will rebuild.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

RAID 5 Single drive failure will rebuild.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

RAID 10 Only one drive in a mirrored set can fail.
  1. Determine which drive is defective by using the RAID management utility (if available) or with diagnosis LEDs on the controller or enclosure.

  2. Replace with an identical hard drive.

Note: Do not change the order of the drives.

  1. The array may be accessible during the rebuild, but you should let the controller rebuild without interruption so that performance is not compromised.

 

If your setup components support USB 3.1 but you are experiencing slower transfer speeds than you expected, consider the following:

  • A USB host connection with multiple USB 3.1 ports might not be able to support 10Gbps on each port simultaneously.
  • The type of port on a device does not determine whether the device is capable of USB 3.1 speeds. A USB-C port might not support USB 3.1 speeds, while USB-A and USB-B ports might support USB 3.1 speeds.
  • Any other devices that you include in your setup, such as an older hard drive in a USB 3.1 enclosure, might create a point of congestion and slow down transfer speeds.

To confirm the functionality of your USB host connection, its ports, and any other devices in your setup, refer to the information provided by the manufacturer.

Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.