StarTech.com

1000 Mbps Gigabit Ethernet PCI Express Multiläges SC-fiberkort - 550 m

Lägg till en multiläges gigabit SC-fiberport till ditt system via PCI Express

Produkt ID: PEX1000MMSC

  • Maximal fiberavstånd på 550 m
  • Kompatibel med PCI Express 1.0a
  • Stödjer väckning över LAN, fjärruppväckning
Visa mer
  • Gränssnitt för avancerad konfiguration för strömhantering (ACPI) 2.0
  • Stödjer upp till 7K bytes jumboram i Windows® 7/Vista (4 KB i äldre operativsystem)
  • Avlastning av Microsoft NDIS5 (IP, TCP, UDP) kontrollsumma
  • Verktyg för kabeldiagnostik
  • Kompatibel med RFC 1157 SNMP v1 vilket gör fjärrstyrning möjlig
  • 1000Mbps-Full-duplex
  • Uppfyller IEEE 802.1Q, 802.1p standard
  • Enkel plug-and-play-installation
207,99 € EUR exkl. moms
259,99 € EUR inkl. moms

Överblick

PEX1000MMSC multiläges 1000 Mbps Gigabit Ethernet SC PCI Express-fiberkort på 550 m ger en perfekt lösning för den som vill dra fiberkablar till skrivbordet. Den gör om en ledig PCIe-kortplats till en multiläges SC-fiberanslutning.

En enkel lösning för att ansluta en dator direkt till ett höghastighetsfibernätverk. Gigabit Ethernet fiberkortsadapter passar stora bandbreddsapplikationer perfekt med stöd för hel duplexdrift och överföringshastigheter i gigabit.

Perfekt för installationer av säkra nätverk. PEX1000MMSC ger en direkt fiberanslutning som inte störs lätt av elektriska störningar som RJ45 standardnätverk.

Täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Fördelarna med StarTech.com

  • Uppnå och behåll gigabit-hastigheter på en fjärrterminal över långa sträckor för att få maximal genomströmning
  • Perfekt för säkra installationer. Med direktfiber förekommer det inte elektroniska störningar som med RJ45 standardnätverkskort
  • PCI Express uppnår verkligen gigabit-hastigheter till skillnad från liknande PCI-fiberkort

Användning

Lägg till en 1000 Mbps SC fiberanslutning till en PCI-kompatibel PC

Lägg till en nätverksanslutning till en dator som är upp till 550 m bort

Skapa en säker anslutning mellan PC:n och en fiberswitch

Perfekt för inbäddade och industriella fjärrsystem för övervakning och höghastighets videoövervakning

Tekniska specifikationer

Information om garanti
Garanti 2 Years
Hårdvara
Busstyp PCI Express
Chipset-ID Realtek - RTL8168B
Gränssnitt Fiber Ethernet
Industristandarder IEEE802.3z 1000Base-SX, IEEE802.3x, IEEE802.1Q, IEEE802.1p, IEEE802.3ad
Korttyp Standardprofil
Portar 1
Prestanda
Kompatibla nätverk 1000 Mbps (1 Gbps)
Maximal kabellängd 550 m [1804 ft]
Våglängd 850nm
Kontakt(er)
Externa portar 1 - Fiberoptisk SC duplex Hona
Kontakttyp(er) 1 - PCI Express x1 Hane
Mjukvara
OS-kompatibilitet Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista (32/64), XP (32/64)
Windows® Server 2012, 2008 R2
Mac OS® 10.x (Tested up to 10.9)
Linux
Särskilda anmärkningar/krav
Obs. Ej kompatibel med 10/100
Indikatorer
LED-indikatorer 2 - Länk och aktivitet
Miljö
Drifttemperatur 0°C to 45° C (32°F to 113°F)
Förvaringstemperatur -10°C to 70°C (14°F to 158°F)
Luftfuktighet 5 % - 95 % icke-kondenserande
Utseende
Produktbredd 83 mm [3.3 in]
Produkthöjd 20 mm [0.8 in]
Produktlängd 109 mm [4.3 in]
Produktvikt 80 g [2.8 oz]
Förpackning
Fraktvikt (förpackning) 0.7 kg [1.5 lb]
Vad det är i lådan
Ingår i paketet 1 - PCI Express Gigabit Ethernet-adapter
1 - Enhets-/Instruktionsbruksanvisning på CD ROM

Kompatibilitet

Se alla kompatibla operativsystem
Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista (32/64), XP (32/64)
Windows® Server 2012, 2008 R2
Mac OS® 10.x (Tested up to 10.9)
Linux

Certifikat

Relaterade produkter

100Mbps Full/Low Profile Ethernet Multi Mode SC Fiber PCI NIC Card 2km
PCI100MMSC
100Mbps Full/Low Profile Ethernet Multi Mode SC Fiber PCI NIC Card 2km

Connect a PC directly to a multimode SC fiber network through an available PCI slot

152,99 € exkl. moms
191,24 € inkl. moms

Produktsupport

Drivrutiner & hämtningsbara filer

Drivrutin(er):
Manual(er):
Specifikation(er)

Vanliga frågor

Before You Buy

Different optical cables are needed for different applications. Before you select a cable to interconnect fiber devices, make sure that the following things match:

  • Mode: Single Mode or Multi Mode.

  • Wavelength: For example, 850 nm, 1310 nm, or 1550 nm.

Note: The above properties cannot be converted or changed by a cable.

When you select a cable, make sure that the cable ends (for example, LC, SC, ST, or MT) match the fiber media devices.

Simplex and duplex ends are available for most connector types. Simplex cables have the connectors separate, where duplex cables have the transmit (TX) and receive (RX) connectors joined together.  

It does not matter which diameter or OM classification the cable uses, as long as it meets the mode requirement.

When you use fiber devices and cables, make sure that the same fiber standards are being used on either end of the fiber network.

Installation

Prior to installing this device, ensure that your operating system is up to date (for example, you have installed the most recent service pack).

To install the driver:

  1. Download the latest drivers from the StarTech.com website (http://www.startech.com/Support). You can find the part number and product ID on the product’s packaging.

Note: Windows will typically save the files to the Downloads folder that is associated with your user account (for example, C:\Documents and Settings\your_name\My Documents\Downloads).

  1. Once the download is complete, right-click the zip folder that you downloaded, select Extract All, and follow the on-screen instructions.
  2. Select the appropriate folder for your operating system.
  3. Double-click Setup.exe.
  4. Follow the on-screen prompts to install the device drivers and restart the computer when prompted.
  5. Your computer will automatically complete the driver installation and your device should be ready to use.

Hur man

StarTech.com does not support a Preboot Execution Environment (PXE) as this requires third-party software. However, our devices can be used as long as the following conditions are met:

  1. The BIOS must support PXE.
  2. The BIOS must see the card.
  3. The environment must have drivers for the chipset used in the card.
  4. If using a USB networking card, the environment must have support for USB devices as well.

To confirm that Windows detects your expansion card, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

To confirm that the Mac OS detects your expansion card, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your expansion card is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

Your expansion card is listed according to the name of the chipset. To determine the name of the chipset of your expansion card, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Problemsökning

When you troubleshoot issues with a network adapter, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Ethernet cables
  • Network devices
  • Computer system

To test your setup components, try the following:

  • Use the Ethernet cables, network devices, and computer system in another setup to see if the problem is with the components or the setup.
  • Use different Ethernet cables, network devices, and a different computer system in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.
  • Use short cables when you are testing.

When you test the Ethernet cables, network devices, and computer system, it is recommended that you do the following:

Sometimes an on-board network interface card (NIC) conflicts with a new NIC.  In these cases it is best to disable the on-board NIC.

The best way to disable your on-board NIC is to go into your BIOS and disable it there if possible.  To do this, consult your motherboard manual.

You can also disable any NIC in Windows.  Here is how you do this:

First click Start, or, in Windows 10 and 8, hold down the Windows key and press X.  Then click Control Panel.

Windows 10

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows 8

  1. Click Network and Sharing Center.
  2. On the left, click Change adapter settings.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows 7

  1. Click Network and Internet.
  2. Click Network and Sharing Center.
  3. On the left, click Change adapter settings.
  4. Right-click the NIC that you would like to disable and select Disable.

Windows Vista

  1. Click Network and Sharing Center.
  2. On the left, click Manage network connections.
  3. Right-click the NIC that you would like to disable and select Disable.

Windows XP

  1. Click Network Connections.
  2. Right-click the NIC that you would like to disable and select Disable.

If you are experiencing speed or connectivity issues, it is best to set a specific speed at half or full duplex in your settings.  You can set your network adapter to perform at a certain speed, but the device that the adapter is connected to (whether it is a router, switch, or computer) must also be able to perform at the same speed.

Note: You must log in as the local administrator before you continue.

To open Device Manager:

  • Press Windows key + R.
  • Type devmgmt.msc.
  • Click OK.
  1. Open the Networking adapters section.
  2. Right-click the network adapter that you want to change and select Properties.
  3. Click the Advanced tab.
  4. Scroll down to Speed & Duplex. By default, it is set to Auto-Negotiate. Select any of the speeds that you see in the list.
  5. Click OK and restart your computer.