HDMI over CAT5 HDBaseT Extender - Power over Cable - Ultra HD 4K

Extend HDMI® up to 230ft (70m) over a single CAT5e/6 cable with Power over Cable to Receiver

Produkt ID: ST121HDBTE

  • Extend video where power outlets are limited with power over cable that powers both the transmitter and receiver using a single power source at either side of the connection
  • Maintains astonishing picture quality up to 115 ft. (35 m) away, with support for UltraHD 4K over non-proprietary CAT5e or CAT6 cabling
  • Also supports HD video resolutions such as 1920x1200 or 1080p at distances up to 230 ft. (70m)
Ditt pris
€288,99 EUR excl. VAT
€361,24 EUR incl. VAT

The StarTech.com HDBaseT extender kit, extends HDMI up to 230 feet (70 Meters) over a single CAT5e or CAT6 cable. The extender supports Ultra HD and Full HD resolutions (4K / 1080p) with support for 3D and the accompanying digital audio. For added versatility, both the transmitter and receiver can be powered by the same single power source using Power Over Cable (POC). The versatility of this video extender makes it an ideal solution for digital signage applications in large buildings such as commercial shopping centers, stadiums, schools, and hospitals.

What is HDBaseT?

HDBaseT is a standardized, zero latency, video distribution technology that’s revolutionizing HDMI distribution. HDBaseT uses an advanced method of modulation that enables you to distribute uncompressed HDMI audio and video along with additional signals such as 100BaseT Ethernet, IR, RS-232 serial and power over cable.

HDBaseT logo

Extend more with HDBaseT

The extender offers HDBaseT technology with HDMI and Power in a single extender kit, for complete end-to-end solution. Offering greater versatility than traditional HDMI extenders or HDMI cabling alone HDBaseT is the clear choice for every integrator and system designer. The added benefit of power over cable means you’ll only need one power source at either side of your extension, great for extending video to areas where power outlets may be limited, such as industrial sites.

Astonishing 4K picture quality from an impressive distance

With the A/V industry quickly adopting 4K as the new high-resolution video standard, long range video distribution can be a challenge with standard HDMI cables beginning signal degradation at 30 feet.
With support for 4K you’ll be amazed at how HDBaseT maintains your Ultra HD picture quality, four times the resolution of high-definition 1080p, even at 130 feet away from your video source. Plus, because the extender supports High-Definition 1080p and lower resolutions at 230 feet away, you can comfortably use this extender to make any video source look great.

Simplify your setup

This extender has been specially crafted for a smooth, tidy installation. HDBaseT technology allows for single cable installation, for seamless integration using existing CAT5e or CAT6 infrastructure, avoiding the hassle of running multiple Ethernet cables while, reducing potential failure points. Plus, the added benefit of power over cable means you’ll only need one power source to power both your extender and receiver, great for extending to areas where power outlets may be limited. Mounting hardware is also included for both the extender and receiver for discrete, professional mounting.

The ST121HDBTE is TAA compliant and backed by a 2-year StarTech.com warranty with free lifetime technical support.

Användning

  • Extend HDMI when power outlets are limited, with only a single power adapter required at either the Transmitter or Receiver, using Power Over Cable
  • Place the display in a convenient viewing area, while the system equipment is placed elsewhere in a clean and secure environment
  • Optimize placement of your demo stations at tradeshows and in auditoriums

Fördelarna med StarTech.com

  • Requires only a single power adapter for both the Transmitter and Receiver
  • Cost-effective HDMI extension through non-proprietary network cabling
  • Optional mounting hardware included for a tidy, professional installation

Partnernummer

  • Ingram Micro Sweden V932810
  • ALSO Sweden 000000000002764139
  • UPC 065030851107

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Height 65 mm [2,6 in]
Package Length 15,6 cm [6,1 in]
Fraktvikt (förpackning) 1,1 kg [2,4 lb]
Package Width 23,5 cm [9,3 in]
Hårdvara AV-ingång HDMI
AV-utgång HDMI
Portar 1
Kablage Cat 5e UTP eller bättre
Audio Ja
Kedjekoppling Nej
Indikatorer LED-indikatorer 1 - status LED (local)
1 - status LED (remote)
Kontakt(er) Connector A 1 - HDMI (19-stifts)
1 - RJ-45
Connector B 1 - HDMI (19-stifts)
1 - RJ-45
Miljö Drifttemperatur 0°C to 40°C (32°F to 104°F)
Förvaringstemperatur -10°C to 60°C (14°F to 140°F)
Luftfuktighet 0% - 80 % RH (non-condensing)
Prestanda Maximal kabellängd 70000
Maximalt avstånd 70 m / 230 ft
Maximal digital upplösning 4096 x 2160 (4K) vid 30 Hz (35 meter)
1920 x 1080 (1080p) vid 60 Hz (70 meter)
Stödda upplösningar 3840x2160 (4K)
2560x1600
1920x1200
1920x1080 (1080p)
1280x720 (720p)
Stöd för widescreen Ja
Audio-specifikationer 7.1 Surround Sound
Medeltid mellan fel (MTBF) 52,000 hrs.
Ström Power Source AC-adapter medföljer
Inspänning 100 - 240 AC
Inström 0.5A
Utspänning 12V DC
Utström 1.5A
Polaritet på mittpol Positiv
Kontakttyp M
Strömförbrukning 3
Särskilda anmärkningar/krav Obs. If you want to add more displays, you can daisy chain this product with the HDBaseT repeater ST121HDBTRP.
Utseende Produktvikt 428 g [15,1 oz]
Färg Svart
Kabinettyp Aluminium
Produktlängd 8 cm [3,1 in]
Produktbredd 67 mm [2,6 in]
Produkthöjd 2,5 cm [1,0 in]
Vad det är i lådan Ingår i paketet 1 - HDMI over CAT5e/6 transmitter unit
1 - HDMI over CAT5e/6 receiver unit
1 - universal power adapter (NA/EU/UK/AU)
1 - mounting bracket kit
2 - grounding wires
1 - instruction manual

Tillbehör

SVA12M2NEUA

DC-strömadapter - 12 V, 2 A

Byt ut din borttappade eller trasiga strömadapter

Ditt pris
€24,99 EUR excl. VAT
€31,24 EUR incl. VAT
SVA12M5NA

DC-strömadapter - 12 V, 5 A

Byt ut din borttappade eller trasiga strömadapter

Ditt pris
€62,99 EUR excl. VAT
€78,74 EUR incl. VAT
VS440HDMI

4x4 HDMI Matrix Video Switch Splitter with Audio and RS232

Share and switch four distinct HDMI® audio/video signals between four displays

Ditt pris
€791,99 EUR excl. VAT
€989,99 EUR incl. VAT
IM12D1500P

12 V DC 1,5 A universell strömadapter

Byt ut din strömkabel på 12 V DC (1,5 A) mot en tillförlitlig anslutning

Ditt pris
€21,99 EUR excl. VAT
€27,49 EUR incl. VAT
ST121HDBTRP

HDBaseT-repeater för ST121HDBTE eller ST121HDBTPW HDMI-förlängarpaket - 4K

Gör om din HDBaseT-förlängare till ett skalbart fördelningssystem genom att leverera HDMI-innehåll till extra områden

Ditt pris
€393,99 EUR excl. VAT
€492,49 EUR incl. VAT
ST124HD4K

4K HDMI-video-splitter med 4 portar – 1x4 HDMI-splitter med hölje i solitt aluminium – 4K @ 30 Hz

Dela en HDMI audio/video-källa på två separata HDMI-skärmar samtidigt, med stöd för upplösningar på upp till 4K

Ditt pris
€107,99 EUR excl. VAT
€134,99 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Installation

To get the highest quality signal from your source to your display when you use an HDMI extender, do the following:

  • Make sure that the HDMI versions of the source, extender, and destination are compatible. For example, if you require 3D support, make sure that all of the devices can support 3D over HDMI.

  • Use the least amount of adapters, splitters, or converters as possible. Each device that you use in your setup creates additional points of potential failure and creates more steps for an HDCP key to hop through, which may cause issues with older displays. For more information on HDCP, refer to the following FAQ: http://www.startech.com/faq/video_signal_converters_HDCP.

  • Use an HDMI extender that exceeds the requirements of the setup. For example, if you need to extend the signal 200 feet, it is best to use an extender capable of more than 200 feet.

  • Make sure that all of the CAT 5/6 runs are as straight as possible, with the least amount of coiling.

  • Make sure that all of the patches, wall jacks, and cables use the highest possible CAT specification, (for example, CAT 6), and were tested to conform to the standard.

  • Use patches, wall jacks, and cables with the same pin configuration. For more information on T568A versus T568B wiring, refer to the following FAQ: http://www.startech.com/faq/network_cables_a_vs_b_pinout.

  • Keep the cabling away from sources of high noise.

  • Make sure that you use adequate electrical grounding in your setup.

There are a few things you'll want to take care of before you deploy your new video extender in your setup.

It’s important to make sure you have everything you will need ahead of time. These items are listed below.

  • Transmitter
  • Receiver
  • Video source
  • Display
  • Video cables
  • (Optional) Ethernet or fiber cables
  • (Optional) Power adapter(s)

It’s also important to test everything in a simplified setup ahead of time to make sure everything works and that you understand how it works. 

In order to set up your video extender, complete the following:

  1. Position your video transmitter near your video source.
  2. Connect the video output from your video source to the video transmitter.
  3. (Optional) Connect the power adapter to the video transmitter.

Note: Not all video extenders require external power, or require external power on both ends.  Refer to the manual for more information.

  1. Position your video receiver near your display.
  2. Connect the video output from your video receiver to your display.
  3. (Optional) Connect the power adapter to the video receiver.
  4. If using a wired video extender, connect your network cabling between the video transmitter and the video receiver.
  5. (Optional) If you are extending anything else supported by your video extender connect those devices to the transmitter and receiver.
  6. (Optional) If you are using a wireless extender, there may be a sync button you need to press to pair the transmitter and receiver.

Now that you have set up your video extender, you can check that everything is working.  You should be able to see your video source's output on the display connected to the video receiver.

If at this point you have further questions regarding a Startech.com video extender, contact our technical support team for further assistance. 

Problemsökning

When you troubleshoot issues with a video extender, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Video and Ethernet cables

  • Video extender

  • Video source (such as a DVD player or computer)

  • Video destination (such as a monitor or projector)

Note: When you are testing setup components, you should avoid using video adapters. For example, if you are converting a VGA source to HDMI for use with an HDMI extender, you should use an HDMI source when you test the components.

To test your setup components, try the following:

  • Use the cable, video extender, video source, and video destination in another setup to see if the problem is with the components or the setup.

  • Use a different cable, video extender, video source, and video destination in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.

  • Use short cables when you are testing.

When you test the video source and video destination, it is recommended that you do the following:

  • Remove the video extender from your setup and test to make sure that the video source and video destination work together without the video extender.

  • Test to make sure that the video source and video destination work together at the resolution that you want to use.

Note: In order for your setup to work properly, the video source, extender, and destination all need to support the resolution that you are using.

This device supports up to 4Kx2K resolutions @30 Hz with a color depth of 8 bits. If you are running a 4K resolution at a refresh rate higher than 30 Hz or a color depth higher than 8 bits, your display will appear blank.

To resolve this issue, you need to lower the resolution, refresh rate, or color depth, by completing any of the following:

  • Connect a display to OUT 1 that is only capable of 4K at 30 Hz with a color depth no higher than 8 bits.  
  • Connect the least capable display to OUT 1.
  • Connect an additional display to your video source (for example, a video card in a computer) and use this display to reconfigure the display connected to OUT 1 to run at 30 Hz and 8 bits color depth (or lower).

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen