4K HDMI över IP-mottagare för ST12MHDLAN4K

Use this 4K receiver with your HDMI extender over IP kit (ST12MHDLAN4K) to scale the extender to additional displays for your video wall or other digital signage applications

Produkt ID: ST12MHDLAN4R

  • Mångsidig videosändning med stöd för stora flerskärmspresentationer, videoväggar, videoväxling och punkt-till-punkt-förlängning
  • Enastående bildkvalitet över IP med stöd för 4K-upplösning vid 30 Hz
  • Gratis mobilapp gör hantering av växlande videoväggskontroll enkel (iOS/Android/Chrome)
Ditt pris
€462,99 EUR excl. VAT
€578,74 EUR incl. VAT

Denna 4K HDMI® över IP-mottagare fungerar med 4K HDMI över IP-förlängarpaketet (säljs separat) och låter dig förlänga en 4K HDMI-signal samt RS-232-enhetsanslutningar över ditt nätverk. Du kan använda extra mottagare (säljs separat) för att sända HDMI-signalen till flera platser, alla med 4K-stöd, och kombinera dina fjärrskärmar för att skapa en videovägg.

IP-mottagaren har även RS-232-förlängning så att du kan lägga till en fjärrstyrd seriell enhet vid din videokälla eller vid varje avlägsen skärm. Denna HDMI över IP-förlängare är den perfekta lösningen för att kombinera en seriestyrd pekskärm med din skärm eller videovägg för att skapa en interaktiv presentation med din digitala skylt.

Förlängd skalbarhet

Videoväggskonfiguration

Lägg till flera mottagare i ditt HDMI över IP-förlängarpaket för att skapa en punkt-till-punkt-konfiguration eller videovägg. I sådana konfigurationer kan du dessutom ansluta en eller flera källor (sändare) till flera skärmar (mottagare) över din Gigabit Ethernet-switch med IGMP. För ytterligare skalbarhet kan du kombinera upp till 16 (sändare) och så många mottagare (skärmar) som din nätverksbandbredd har stöd för.

Förlängaren har även en separat 3,5 mm audiokälla så att du kan växla mellan inbyggd HDMI-audio och en separat 3,5 mm audiokälla och sända en audiokälla till flera avlägsna platser över IP (en Gigabit Ethernet-switch med IGMP behövs också).

Ultra HD 4K-upplösning vid 60 Hz

Detta HDMI över IP-paket använder H.264-komprimering för att ge enastående 4K UHD-video till dina avlägsna 4K-skärmar över en IP-anslutning. Med stöd för 4K kan du nå en upplösning på upp till 3840x2160p vid 30 Hz så att du kan förlänga en 4K-videokälla till flera avlägsna platser - perfekt för digitala skyltar eller sändning av underhållningsvideo genom en stor byggnad som till exempel skolor, sjukhus eller köpcentrum.

Förlängaren är bakåtkompatibel med lägre upplösningar som till exempel 1080p eller 720p, perfekt för lägre upplösningar och samtidigt framtidssäkra din infrastruktur för 4K-implementering.

Hantera din videodistribution från din mobila enhet

Detta HDMI-distributionspaket har en enkel app för videokontroll som hjälper dig hantera din IP videodistribution. Appen är enkel att konfigurera med automatisk hårdvaruavkänning och den låter dig växla mellan videokällor för enkel fjärrvisning. Du kan dessutom skapa och hantera en videovägg för en imponerande digital skylt som definitivt fångar din publiks uppmärksamhet.

Mjukvaran finns på iOS för din iPhone eller iPad, Android™ för din smarttelefon eller surfplatta och Google Chrome™-webbläsare.

Professionell, kostnadseffektiv, enkel installation

Med HDMI över IP-förlängarpaketet följer valfri monteringsutrustning för en städad installation. Och eftersom förlängaren använder standard CAT5e eller CAT6 Ethernet-kabel med RJ-45-kontakter slipper du både kostnaden och besväret med att dra specialkablar.

Förlängaren har också en EDID-funktion som ger optimal upplösning och maximal kompatibilitet med skärmen eller projektorn för en praktisk plug-and-play-installation.

Ladda ned StarTech.coms Video Control-program för att hantera din IP-sändning. 

Apple App Store-logotyp

Google Play App Store-logotyp

Chrome Store-logotyp

ST12MHDLAN4R täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Obs.: För bästa prestanda rekommenderas en hanterad nätverksomkopplare med IGMP för mer än en sändare, eller fler än fyra mottagare. Icke-hanterade nätverksomkopplare kommer också att begränsa prestanda för andra enheter i ditt nätverk. Stöd för jumboramar måste vara aktiverat för att distribuera 4K-video.

Användning

  • Sänd en separat 3,5 mm audiokälla och växla mellan källan och den inbyggda HDMI-audiokällan
  • Bygg en videovägg med flera skärmar för att underhålla dina stamkunder med en imponerande skärm i en restaurang eller i ett köpcenter
  • Förläng HDMI och seriell RS-232 för att skapa en interaktiv digital skylt
  • Visa flera kommunikationstavlor som visar dynamisk data som till exempel tider och datum på digitala tabeller på flygplatser, tågstationer, busstationer eller sjukhus, som kan uppdateras när som helst
  • Presentera flöden från din sociala media på flera skärmar på ett stort visningsområde

Partnernummer

  • Ingram Micro Sweden V934163
  • UPC 065030868969

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Fraktvikt (förpackning) 1,2 kg [2,7 lb]
Package Length 29,5 cm [11,6 in]
Package Width 21 cm [8,3 in]
Package Height 65 mm [2,6 in]
Hårdvara Portar 1
AV-ingång HDMI
Kablage Cat 5e UTP eller bättre
Audio Ja
Hyllmonterbar Ja
Kedjekoppling Ja
Kontakt(er) Connector A 1 - HDMI (19-stifts)
1 - RJ-45
2 - RJ-11
4 - 3.5 mm minijack (3-polig)
Miljö Drifttemperatur 0°C to 40°C (32°F to 104°F)
Förvaringstemperatur -10°C to 60°C (14°F to 140°F)
Luftfuktighet 0% - 80 %
Prestanda Maximalt avstånd 100 m / 330 ft
Maximal digital upplösning 4K @ 30Hz
Stödda upplösningar 3840x2160 (4K) @ 30Hz
2560x1600
1920x1200 @ 60Hz
1920x1080 (1080p)
1280x720 (720p)
Stöd för widescreen Ja
Audio-specifikationer Stereoljud
Ström Power Source AC-adapter medföljer
Inspänning 100 - 240 AC
Inström 0.6 A
Utspänning 12V DC
12V DC
Utström 1.5 A
Polaritet på mittpol Positiv
Kontakttyp M
Strömförbrukning 18
Särskilda anmärkningar/krav Obs. Bandwidth requirement at 4k 30hz resolution is between 480Mbps and 850Mbps (per transmitter and receiver pair)
Latency at 4K 30hz resolution is 200ms between transmitter and receiver
Utseende Färg Svart
Kabinettyp Aluminium
Produktlängd 13,1 cm [5,2 in]
Produktbredd 117 mm [4,6 in]
Produkthöjd 3 cm [1,2 in]
Produktvikt 594 g [21,0 oz]
Vad det är i lådan Ingår i paketet 1 - HDMI över IP-mottagare
1 - universell strömadapter (NA, EU, UK, ANZ)
1 - Monteringsfäste
1 - Cat5-kabel
1 - RJ11 till RS232-adapter
1 - RJ11-kabel
1 - skruvmejsel i plast
1 - snabbstartsguide

Tillbehör

SVA12M2NEUA

DC-strömadapter - 12 V, 2 A

Byt ut din borttappade eller trasiga strömadapter

Ditt pris
€24,99 EUR excl. VAT
€31,24 EUR incl. VAT
SVA12M5NA

DC-strömadapter - 12 V, 5 A

Byt ut din borttappade eller trasiga strömadapter

Ditt pris
€62,99 EUR excl. VAT
€78,74 EUR incl. VAT
MU6MMS

6 ft Slim 3.5mm Stereo Audio Cable - M/M

Connect an iPhone® or other MP3 player to a car stereo

Ditt pris
€2,99 EUR excl. VAT
€3,74 EUR incl. VAT
MU10MMS

3 m Slim 3,5 mm stereoaudiokabel - M/M

3 m slimmad 3,5 mm stereoaudiokabel

Ditt pris
€3,99 EUR excl. VAT
€4,99 EUR incl. VAT
MU15MMS

4,5 m Slim 3,5 mm stereoaudiokabel - M/M

Anslut enkelt en iPod eller annan MP3-spelare till stereon

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
MU6MMRCA

1,8 m stereoaudiokabel - 3,5 mm hane till 2x RCA hane

Koppla din dator eller ljudspelare till en RCA-ljudenhet

Ditt pris
€3,99 EUR excl. VAT
€4,99 EUR incl. VAT
IES101002SFP

Gigabit Ethernet switch med lager 2 funktionalitet, 10 portar och 2 öppna SFP-platser – kan monteras i datarack

Skala dit nätverk och anslut upp till 10 olika Gigabit Ethernet-enheter inklusive 8x RJ45 + 2x fiberoptiska anslutningar med de SFP:er du föredrar

Ditt pris
€243,99 EUR excl. VAT
€304,99 EUR incl. VAT
ST12MHDLAN4K

HDMI över IP-förlängarpaket - 4K

Använd HDMI över LAN och få en video över IP-lösning som är skalbar och har intuitiv kontroll som är idealisk för din videovägg eller annan digital skylt

Ditt pris
€925,99 EUR excl. VAT
€1 157,49 EUR incl. VAT
HDMIDVIMM6

6 ft HDMI to DVI-D Cable - M/M

Connect an HDMI®-enabled output device to a DVI-D display, or a DVI-D output device to an HDMI-capable display

Ditt pris
€10,99 EUR excl. VAT
€13,74 EUR incl. VAT
HDMIDVIMM10

3 m HDMI till DVI-D-kabel - M/M

Anslut en HDMI®-kompatibel utdataenhet till en DVI-D-skärm eller en DVI-D-utdataenhet till en HDMI-kompatibel skärm

Ditt pris
€12,99 EUR excl.
€12,99 EUR incl.
MU3MMRCA

3 ft Stereo Audio Cable - 3.5mm Male to 2x RCA Male

Connect your Computer or Audio Player to an RCA Audio Device

Ditt pris
€5,99 EUR excl. VAT
€7,49 EUR incl. VAT
VIDWALLMNT

Videoväggfäste - utdragbar konstruktion - finjusteringar

Videoväggsystem för TV | Stål | Stöldskydd | För 45- till 70-tums skärmar

Ditt pris
€437,99 EUR excl. VAT
€547,49 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Hur man

  1. Open Google Chrome.
  2. Click the Menu button.  This button is indicated by three horizontal lines or three dots stacked on top of each other.
  3. Click Settings.
  4. Under Internet connection click twice on the network you want to set the IP address for.
  5. Click the Network tab.
  6. Uncheck the Configure automatically checkbox.
  7. Under IP address: enter the new IP address.
  8. If necessary, repeat step 7 for the Subnet mask and the Gateway.
  9. Click Close.
  1. Tap the Settings app.
  2. Tap Wi-Fi.
  3. Touch and hold the network that you want to set the IP address for.
  4. Tap Manage network settings.

Note: Depending on the type of smartphone you are using and the version of the Android OS you are running, the text you see in step 4 might differ from Manage network settings.

  1. Select the Show advanced options check box.
  2. Under IP settings, tap the drop-down box.
  3. Tap Static.
  4. Enter the new IP address.
  5. If necessary, repeat step 8 for the gateway.
  6. Tap Save.

To change your IP address so that you can access a specific device, complete steps 1 to 6, then tap DHCP to access the Internet again. 

  1. Click the Settings icon.
  2. Click Wi-Fi.
  3. Next to the name of the Wi-Fi network that you want to set the IP address for, click the blue i.
  4. Click the Static tab.
  5. In the IP Address field, enter the new static IP address.
  6. If necessary, repeat steps 4 and 5 for the Subnet Mask and Router fields.
  7. To save the changes, click the Wi-Fi networks icon.

Note: If you are changing your IP address to access a specific device, repeat steps 1 to 3, and then click the DHCP tab to access the Internet again.

Installation

To get the highest quality signal from your source to your display when you use an HDMI extender, do the following:

  • Make sure that the HDMI versions of the source, extender, and destination are compatible. For example, if you require 3D support, make sure that all of the devices can support 3D over HDMI.

  • Use the least amount of adapters, splitters, or converters as possible. Each device that you use in your setup creates additional points of potential failure and creates more steps for an HDCP key to hop through, which may cause issues with older displays. For more information on HDCP, refer to the following FAQ: http://www.startech.com/faq/video_signal_converters_HDCP.

  • Use an HDMI extender that exceeds the requirements of the setup. For example, if you need to extend the signal 200 feet, it is best to use an extender capable of more than 200 feet.

  • Make sure that all of the CAT 5/6 runs are as straight as possible, with the least amount of coiling.

  • Make sure that all of the patches, wall jacks, and cables use the highest possible CAT specification, (for example, CAT 6), and were tested to conform to the standard.

  • Use patches, wall jacks, and cables with the same pin configuration. For more information on T568A versus T568B wiring, refer to the following FAQ: http://www.startech.com/faq/network_cables_a_vs_b_pinout.

  • Keep the cabling away from sources of high noise.

  • Make sure that you use adequate electrical grounding in your setup.

To create a video wall with ST12MHDLAN, do the following:

  • Obtain the StarTech.com Video Switching & Wall Control app from the Google Play™ store or the App Store.
  • Use multiple receivers (for example, ST12MHDLANRX) in conjunction with multiple transmitters to create the video wall.
  • Use a wireless network infrastructure (for example, a wireless access point) in conjunction with a managed switch.
  • Make sure that your mobile device is connected to the same network as the ST12MHDLAN.

Note: The video wall cannot be created with switches that are not managed. For more information about why a managed switch is required, visit http://www.startech.com/faq/video_extenders_st12mhdlan_video_wall_network_requirements. A layer two managed Gigabit Ethernet switch () is recommended for use in video wall setups.

The following example describes how to create a 2 x 2 video wall that uses two video inputs. The information contained in the example can be applied to setups with multiple switches, receivers, and transmitters.

Hardware

The following is a list of the hardware components used in the example setup:

  • Two of the .
  • Two of the .
  • One of the .
  • CAT 5e (or greater) Ethernet cables.
  • HDMI® cables.
  • Four HDMI displays.
  • Two HDMI sources (for example, computers).
  • A computer that is connected by wired Ethernet.
  • A mobile device that is running Android™ or iOS®, and has the StarTech.com Video Switching & Wall Control app installed on it.

Configure the hardware

  1. Use the Ethernet cables to connect the transmitters and receivers to the IES101002SPF.
  2. Connect the IES101002SPF to the rest of the network.
  3. Use the HDMI cables to connect the receivers to the displays.
  4. Use the HDMI cables to connect the HDMI sources to the transmitters.
  5. Set the thumbwheel to on one transmitter.
  6. Set the thumbwheel to A on all of the receivers.
  7. Set the thumbwheel to B on the remaining transmitter.

When all of the units are powered on and the HDMI sources are transmitting video, there should be mirrored images from source A displayed on the monitors.

Configure the switch

Note: The following instructions are based on the default configuration for the IES101002SFP switch.

To access the configuration settings for the switch, complete the following:

  1. Use an Ethernet cable to connect a computer to one of the ports.
  2. Make sure that your computer's network adapter is on the same network as the network switch (by default, 192.168.2.XXX). For more information on how to change your IP address, refer to the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=networking#ip-address-change-windows-mac-os.

To configure the IGMP on the switch, complete the following:

  1. Use your web browser to navigate to 192.168.2.1. The default login is Username = admin, Password = [blank].
  2. To access the IGMP Snooping Configuration screen, click Configuration > IPMC > IGMP Snooping > Basic Configuration.
  3. In the Global Configuration settings, do the following:
  • Select the Snooping Enabled check box.
  • Select the Unregistered IPMCv4 Flooding Enabled check box.
  • In the IGMP SSM Range field, type 232.0.0.0 /8.
  • Select the Leave Proxy Enabled check box.
  • Select the Proxy Enabled check box.
  1. In the Port Related Configuration settings, do the following:
  • Clear the Router Port check box.
  • Select the Fast Leave check box.
  • Set Throttling to Unlimited.
  1. Click Save.
  2. In IGMP Snooping, click VLAN Configuration.
  3. Click Add New IGMP VLAN.
  4. In the VLAN settings, do the following:
  • Set the VLAN ID settings to 1.
  • Select the Snooping Enabled check box.
  • Select the IGMP Querier check box.
  • Set the Compatibility to IGMP-Auto.
  • Set the RV to 2.
  • Set the QI (sec) to 125.
  • Set the QRI (0.1 sec) to 100.
  • Set the LLQI (0.1 sec) to 10.
  • Set the URI (sec) to 1.
  1. Click Save.

Connect your Android device to the network

To connect to the network for the ST12MHDLAN, you need to connect your mobile device to the 169.254.XXX.XXX network. Depending on the version of the Android operating system that you are running, you many need to manually create a wireless network with a static IP address or assign an IP address for an existing wireless connection.

To connect to the ST12MHDLAN network on a device running Android 5.1.1 (Lollipop) or Cyanogen 12.0, do the following:

  1. Make sure that the StarTech.com Video Switching & Wall Control app is installed on your device.
  2. Click Settings > WiFi.
  3. If you are or were connected to the wireless access point that you want to connect to, select that network and click Forget.
  4. Select the wireless network, and if required, enter your password. 
  5. Click Advanced Options.
  6. Change the IP Settings to Static, and enter the following information:
  • In the IP Address field, enter 169.254.XXX.XXX where XXX is a number between 2-254.
  • Set the Gateway to default.
  • Set the Network prefix length to 16.
  • Set the Other settings to default.

Connect your iOS device to the network

  1. Click Settings > WiFi.
  2. Select the wireless network, and if required, enter your password. 
  3. Click the blue arrow or i next to the network.
  4. Click the Static tab.
  5. Change the IP Settings to Static, and enter the following information:
  • In the IP Address field, enter 169.254.XXX.XXX where XXX is a number between 2-254.
  • Set the Subnet Mask to 255.255.0.0.
  • Set the Router to blank or your default gateway.
  • ​Set the DNS to 8.8.8.8.

Configure the video wall

You should now be able to detect two transmitters and four receivers in the Android application. The inputs can be routed and divided between the receivers and the positioning can be changed to achieve the necessary video wall configuration.

You can disconnect the mobile device from the setup and the setup will retain the configuration as long as the video inputs remain turned on.

Problemsökning

The ST12MHDLAN app is available for iOS, Android, and Google Chrome.  To download and install the app navigate to the StarTech.com website.  You will find a download link for each platform on the ST12MHDLAN product page under the Overview tab. The device on which you install the application will be referred to as the control device.

The control device must be on the same network as your ST12MHDLAN transmitters and receivers. The transmitters and receivers have a default IP address in the range of 169.254.x.x with a subnet mask of 255.255.0.0. If you need to change the IP address to fit your network infrastructure, make sure you keep all devices on the same network.  For example, you can change your transmitter to 192.168.1.100 and your receiver to 192.168.1.101.  There are links in the description to assist you in changing your control device's IP address.

The app will automatically discover any transmitters and receivers that are on the same network as the control device.  These devices will be shown in the Devices tab.

You can manually force the control device to search for any transmitters and receivers by pressing the Refresh button in the Devices tab.

You can access the Menu from any tab within the app.

The menu includes a helpful guide to the app as well as the ability to search a specific IP address for a transmitter or receiver.  The Menu also allows you to turn on Demo Mode which populates the app with virtual devices, allowing you to test configurations as if actual devices were connected.

The Menu also includes Device Administration which you can use to reboot all of your connected devices or reset the connected devices to factory defaults.

On the Devices tab you can adjust the individual settings for each transmitter and receiver.  Simply tap on a device’s name to load that device’s settings.  On the Settings page you can change the name of the device, the IP address and subnet, view error history, and other advanced settings.

The second tab of the ST12MHDLAN app is the Switches tab.  This tab allows you to define which video source is being sent to each video receiver.  You can change the video source quickly and easily by selecting a different source in this tab.

The final tab in the ST12MHDLAN app is titled Walls and allows you to customize your video walls and digital signage.

To create a new video wall, complete the following:

  1. Tap the + icon.
  2. Under Wall Name enter a name.
  3. Assign the video wall a number of rows and columns.
  4. Tap Next.
  5. Assign a receiver to each of the displays in your video wall.  You can tap on a display to change the receiver assigned to that display.
  6. (Optional) Correct for the bezel compensation.

a)Tap Bezel Compensation.

b)Measure your display with and without the bezel, and enter the measurements as indicated in the diagram above.

  1. Tap Save.

As you add more video walls to the Walls tab you can easily modify or delete them by tapping on each entry.

You can manage your video wall in one of two ways:

  • On the Walls tab, tap a video source to select it for a video wall.
  • On the Switches tab, tap a video source to select it for each display.

If at this point you have questions about the ST12MHDLAN review the other videos in this series.  If you would like to learn more about video extenders in general review our video series on that subject. 

When you troubleshoot issues with a video extender, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Video and Ethernet cables

  • Video extender

  • Video source (such as a DVD player or computer)

  • Video destination (such as a monitor or projector)

Note: When you are testing setup components, you should avoid using video adapters. For example, if you are converting a VGA source to HDMI for use with an HDMI extender, you should use an HDMI source when you test the components.

To test your setup components, try the following:

  • Use the cable, video extender, video source, and video destination in another setup to see if the problem is with the components or the setup.

  • Use a different cable, video extender, video source, and video destination in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.

  • Use short cables when you are testing.

When you test the video source and video destination, it is recommended that you do the following:

  • Remove the video extender from your setup and test to make sure that the video source and video destination work together without the video extender.

  • Test to make sure that the video source and video destination work together at the resolution that you want to use.

Note: In order for your setup to work properly, the video source, extender, and destination all need to support the resolution that you are using.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen