HDBaseT över CAT5 HDMI-mottagare för ST424HDBT - 70 m - 1080p

Förläng HDMI-signalen från din ST424HDBT* matrisswitch över Cat5/Cat6-kabel med IR-kontroll

Produkt ID: STHDBTRX

  • IR-förlängnings/mottagarkablar medföljer
  • 70 m HDMI-förlängning över Cat5/6-kablage
  • Med stöd för videoupplösning på upp till 1920x1200/1080p
Ditt pris
€172,99 EUR excl. VAT
€216,24 EUR incl. VAT

HDBaseT-mottagaren fungerar med /sv-se/audio-video-products/st424hdbt HDMI-matrisswitchen för att förlänga en HDMI-audio/video-källa med upp till 70 m över Cat5e/6-kablage. En STHDBTRX mottagarenhet behövs för varje individuell fjärrskärm.

Cat5 HDMI-mottagaren arbetar tillsammans med ST424HDBT för att skapa en lösning för digitala skyltar som med en HDMI-matrisswitch och -förlängare i ett trasselfritt system eliminerar kostnaden och problemet med att använda flera enheter. Eftersom signalen förlängs med standard Cat5e/6 Ethernet-kablar med RJ45-kontakter så kan du använda befintligt kablage utan den extra kostnaden med specialkablar eller -kontakter.

För fjärranvändning av källor kan HDMI-mottagaren även förlänga en infraröd signal från en fjärrkontroll för att styra antingen skärmen eller videokällan från ena sidan eller systemet, med medföljande IR-förlängare och mottagarkablar.

STHDBTRX täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Användning

  • Välj vilka videokällor som ska visas och växla mellan källorna när som helst
  • Anslut 4 olika HDMI-källor till 4 olika skärmar på olika platser i en stor byggnad som till exempel ett köpcentrum, en skola eller ett sjukhus
  • Placera skärmarna i ett lämpligt uppvisningsområde medan HDMI-utrustningen placeras någon annanstans i en separat och säker miljö

Fördelarna med StarTech.com

  • Kostnadssparande installation med vanligt Cat5e/Cat6-kablage
  • Eliminera trassel och reducera felpunkter med en allt-i-ett HDMI-switch, -splitter och -förlängare med medföljande monteringsfästen
  • Problemfri användning med seriell, Ethernet- eller IR-kontroll

Partnernummer

  • Ingram Micro Sweden V933030
  • UPC 065030855013

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Height 74,0 mm [2,9 in]
Package Length 21,1 cm [8,3 in]
Package Width 14,8 cm [5,8 in]
Fraktvikt (förpackning) 558,0 g [19,7 oz]
Hårdvara AV-ingång Ethernet
AV-utgång HDMI
Portar 1
Kablage Cat 5 UTP eller bättre
Audio Ja
Chipset-ID Valens - VS010
Kedjekoppling Ja
Indikatorer 1 - LED-indikatorer Ström
Länk
Läge
Länk
HDCP
Kontakt(er) 1 - Connector A RJ-45
1 - Connector B IrDA (Infraröd, SIR/FIR)
HDMI (19-stifts)
Miljö Drifttemperatur -5 to 35°C (-41 to 95 °F)
Förvaringstemperatur -5 to 35°C (-41 to +95 °F)
Luftfuktighet 5 till 90 % RH
Prestanda Maximalt avstånd 70 m / 230 ft
Maximal digital upplösning 1920x1200/1080p
Audio-specifikationer 7.1 surroundljud
Ström Power Source AC-adapter medföljer
Inspänning 100 - 240 AC
Inström 0.5 A
Utspänning 5 DC
Utström 2 A
Strömförbrukning 10
Utseende Färg Svart
Kabinettyp Aluminium
Produktlängd 11,0 cm [4,3 in]
Produktbredd 75,0 mm [3,0 in]
Produkthöjd 22,0 mm [0,9 in]
Produktvikt 215,0 g [7,6 oz]
Vad det är i lådan 1 - Ingår i paketet HDMI-mottagarenhet
Monteringsfästen
IR-paket (sändare/mottagare)
Universell strömadapter (NA/UK/EU/AUS)
Snabbinstallationsguide

Tillbehör

HDMIDVIMM6

6 ft HDMI to DVI-D Cable - M/M

Connect an HDMI®-enabled output device to a DVI-D display, or a DVI-D output device to an HDMI-capable display

Ditt pris
€11,99 EUR excl. VAT
€14,99 EUR incl. VAT
SVA5M3NEUA

DC-strömadapter - 5 V, 3 A

Byt ut din borttappade eller trasiga strömadapter

Ditt pris
€21,99 EUR excl. VAT
€27,49 EUR incl. VAT
ST424HDBT

4x4 HDMI-matrisswitch och HDMI över HDBaseT CAT5-förlängare - 70 m - 1080p

Dela och förläng fyra HDMI-videokällor upp till 70 m över Cat5 och växla mellan fyra fjärrskärmar

Ditt pris
€1 721,99 EUR excl. VAT
€2 152,49 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Installation

There are a few things you'll want to take care of before you deploy your new video extender in your setup.

It’s important to make sure you have everything you will need ahead of time. These items are listed below.

  • Transmitter
  • Receiver
  • Video source
  • Display
  • Video cables
  • (Optional) Ethernet or fiber cables
  • (Optional) Power adapter(s)

It’s also important to test everything in a simplified setup ahead of time to make sure everything works and that you understand how it works. 

In order to set up your video extender, complete the following:

  1. Position your video transmitter near your video source.
  2. Connect the video output from your video source to the video transmitter.
  3. (Optional) Connect the power adapter to the video transmitter.

Note: Not all video extenders require external power, or require external power on both ends.  Refer to the manual for more information.

  1. Position your video receiver near your display.
  2. Connect the video output from your video receiver to your display.
  3. (Optional) Connect the power adapter to the video receiver.
  4. If using a wired video extender, connect your network cabling between the video transmitter and the video receiver.
  5. (Optional) If you are extending anything else supported by your video extender connect those devices to the transmitter and receiver.
  6. (Optional) If you are using a wireless extender, there may be a sync button you need to press to pair the transmitter and receiver.

Now that you have set up your video extender, you can check that everything is working.  You should be able to see your video source's output on the display connected to the video receiver.

If at this point you have further questions regarding a Startech.com video extender, contact our technical support team for further assistance. 

To get the highest quality signal from your source to your display when you use an HDMI extender, do the following:

  • Make sure that the HDMI versions of the source, extender, and destination are compatible. For example, if you require 3D support, make sure that all of the devices can support 3D over HDMI.

  • Use the least amount of adapters, splitters, or converters as possible. Each device that you use in your setup creates additional points of potential failure and creates more steps for an HDCP key to hop through, which may cause issues with older displays. For more information on HDCP, refer to the following FAQ: http://www.startech.com/faq/video_signal_converters_HDCP.

  • Use an HDMI extender that exceeds the requirements of the setup. For example, if you need to extend the signal 200 feet, it is best to use an extender capable of more than 200 feet.

  • Make sure that all of the CAT 5/6 runs are as straight as possible, with the least amount of coiling.

  • Make sure that all of the patches, wall jacks, and cables use the highest possible CAT specification, (for example, CAT 6), and were tested to conform to the standard.

  • Use patches, wall jacks, and cables with the same pin configuration. For more information on T568A versus T568B wiring, refer to the following FAQ: http://www.startech.com/faq/network_cables_a_vs_b_pinout.

  • Keep the cabling away from sources of high noise.

  • Make sure that you use adequate electrical grounding in your setup.

Problemsökning

When you troubleshoot issues with a video extender, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Video and Ethernet cables

  • Video extender

  • Video source (such as a DVD player or computer)

  • Video destination (such as a monitor or projector)

Note: When you are testing setup components, you should avoid using video adapters. For example, if you are converting a VGA source to HDMI for use with an HDMI extender, you should use an HDMI source when you test the components.

To test your setup components, try the following:

  • Use the cable, video extender, video source, and video destination in another setup to see if the problem is with the components or the setup.

  • Use a different cable, video extender, video source, and video destination in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test your cables, it is recommended that you do the following:

  • Test each cable individually.

  • Use short cables when you are testing.

When you test the video source and video destination, it is recommended that you do the following:

  • Remove the video extender from your setup and test to make sure that the video source and video destination work together without the video extender.

  • Test to make sure that the video source and video destination work together at the resolution that you want to use.

Note: In order for your setup to work properly, the video source, extender, and destination all need to support the resolution that you are using.

This device supports up to 4Kx2K resolutions @30 Hz with a color depth of 8 bits. If you are running a 4K resolution at a refresh rate higher than 30 Hz or a color depth higher than 8 bits, your display will appear blank.

To resolve this issue, you need to lower the resolution, refresh rate, or color depth, by completing any of the following:

  • Connect a display to OUT 1 that is only capable of 4K at 30 Hz with a color depth no higher than 8 bits.  
  • Connect the least capable display to OUT 1.
  • Connect an additional display to your video source (for example, a video card in a computer) and use this display to reconfigure the display connected to OUT 1 to run at 30 Hz and 8 bits color depth (or lower).

Before You Buy

You should only use video converters and extenders if it is absolutely necessary to do so. In many cases, most video converters and extenders are not necessary if you purchase the correct cable.

The following table lists the maximum length of cable for common video standards.

Video standard Maximum length
DisplayPort 50 ft. (15.2m)
HDMI 50 ft. (15.2m)
DVI 50 ft. (15.2m)
VGA 200 ft. (71m)

Note: StarTech.com offers cables longer than what is listed above, including active cables, which typically include built-in active signal boosters that allow for longer cables. Active cables are specifically designed to exceed the suggested maximum lengths and are tested at the listed specifications (for example, the maximum listed resolution).

Video adapters

Video adapters passively adapt a cable from one connector type to another. Video adapters do not change the signal type, or change the video standard.

Examples of common applications for adapters include the following:

  • DVI-I to VGA

  • RCA to BNC

  • Mini DisplayPort to DisplayPort

  • Couplers (female to female, or male to male)

Note: You can use a coupler to extend a cable for a short distance. However, each coupler that you use can introduce signal loss, which degrades the signal quality.

Video converters

Video converters actively process and change the signal type from one video standard and convert it to another standard. They are typically used to convert digital to analog and vice versa, but can be used to convert a digital signal to another digital video standard (for example, HDMI to DisplayPort).

Video converters work over short distances from the source to the destination: up to 15 feet or 3 meters.

Video extenders

Video extenders convert an input signal to a higher voltage for transmission over longer distances and then convert the input signal back to the original video standard. The input and the output signal will match on a video extender, as the same video standard is maintained end-to-end. If a cable is extended with adapters or converters, the signal quality degrades.

Note: For more information on using a video adapter or converter with a video extender, see the following FAQ: http://www.startech.com/faq/video_signal_converters_convert_then_extend.

If you need to use a video extender with a video adapter or converter, you should position the adapter or converter as close to the video source as possible. For example, if you need to take a VGA signal from a computer and send it 200 feet to an HDMI® projector, you should convert the signal from VGA to HDMI and use an HDMI extender.

Note: For more information on when to use cables or extenders, see the following FAQ: http://www.startech.com/faq/video_signal_converters_when_to_convert.

Yes, this video extender works with set-top boxes, provided the set-top box meets the following requirements:

  • The set-top box must be High-bandwidth Digital Content Protection (HDCP) compliant.
  • The set-top box must support devices being connected between the video source and display. If the set-top box requires a direct cable connection between the video source and display, it won't work with this video extender.

No, this device is designed to be a point-to-point solution using networking cabling only. 

This device outputs HDMI video signals. If you have a display or video destination that uses another type of video connection, there are ways that you can convert the video signal or connection. These options are outlined below and organized by the target connection.

HDCP

When you consider whether to convert an HDMI video signal to another connection type, it is important to know if the media that is being converted from the HDMI video connection is protected by High-bandwidth Digital Content Protection (HDCP). If the media is protected by HDCP, you cannot convert to analog video connections because they do not support HDCP. You may experience this issue when you use devices like Blu-ray players, DVD players, and certain gaming consoles.

Target connection Conversion
VGA HDMI to VGA: https://www.startech.com/AV/Converters/Video/?filter_AVINPUT=HDMI&filter_AVOUTPUT=VGA.
DVI

HDMI to DVI: https://www.startech.com/Cables/Audio-Video/HDMI/HDMI-to-DVI/.

DisplayPort HDMI to DisplayPort: https://www.startech.com/AV/Converters/Video/?filter_AVINPUT=HDMI&filter_AVOUTPUT=DisplayPort.

 

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen
Vänta...