Produkt ID: 25SAT22MSAT
Öka systemets prestanda markant genom att lägga till en dubbel mSATA SSD RAID-array till vilken 2,5" SATA HDD-enhet som helst med 25SAT22MSAT mSATA till SATA-adaptern.
Utnyttja din SATA III-kontrollers fulla potential med mSATA SSD-enheter som reducerar flaskhalsar i dataöverföringarna med hastigheter på upp till 6 Gbps. Med mSATA SSD-enheter sparar du även pengar tack vare lägre strömförbrukning jämfört med vanliga enheter med skivor.
Du kan även få högre SSD-kapacitet eller dataredundans med den dubbla SSD-kontrollern som stöder flera RAID-lägen (RAID 0, 1, BIG). SSD-adaptern stöder även icke-RAID-drift (JBOD) vid användning tillsammans med en SATA-kontroller med stöd för portmultiplicering så att båda enheterna kan användas oberoende av varandra.
Skydda enheten med en öppen ram som garanterar maximal värmeavledning.
25SAT22MSAT täcks av StarTech.coms 2-årsgaranti och livstidsgaranti på teknisk support.
| Warranty Information | Warranty | 2 Years |
|---|---|---|
| Förpackning | Package Height | 32 mm [1,3 in] |
| Package Length | 14,5 cm [5,7 in] | |
| Fraktvikt (förpackning) | 107 g [3,8 oz] | |
| Package Width | 17,4 cm [6,9 in] | |
| Hårdvara | Gränssnitt | SATA |
| Antal enheter | 2 | |
| Enhetsstorlek | mSATA (Full Size & Half Size) | |
| Enhetstyp | mSATA (Mini SATA) | |
| Enhetsinstallation | Fixed | |
| Chipset-ID | JMicron - JMS562 | |
| Indikatorer | 1 - LED-indikatorer | Enhet #1 aktivitet |
| Enhet #1 fel | ||
| Enhet #2 aktivitet | ||
| Enhet #2 fel | ||
| Kontakt(er) | 2 - Enhetskontakter | mSATA (52 pin, Mini SATA) |
| 1 - Värdkontakter | SATA Data & Power Combo (7+15 pin) | |
| Miljö | Drifttemperatur | -40°C to 85°C (-40°F to 185°F) |
| Mjukvara | OS-kompatibilitet | Operativsystemsoberoende, varken programvara eller drivrutiner behövs |
| Prestanda | Maximal dataöverföringshastighet | 6 Gbps |
| Typ och hastighet | SATA III (6 Gbps) | |
| Port Multiplier | Yes | |
| RAID | Yes | |
| RAID-lägen som stöds | RAID 0 (Striped Disks) | |
| BIG (Spanning or Concatenation) | ||
| JBOD - (Just a Bunch of Disks) | ||
| RAID 1 (Mirrored Disks) | ||
| Hot swap-förmåga | No | |
| Medeltid mellan fel (MTBF) | 5,101,299 Hours | |
| Utseende | Produktvikt | 39 g [1,4 oz] |
| Färg | Green | |
| Kabinettyp | Steel, Aluminum and Plastic | |
| Produktlängd | 97 mm [3,8 in] | |
| Produktbredd | 70 mm [2,8 in] | |
| Produkthöjd | 7 mm [0,3 in] | |
| Vad det är i lådan | 1 - Ingår i paketet | Dubbel mSATA till 2,5" SATA-adapter |
| Paket med monteringsskruvar | ||
| Installationsguide |
SATA-kontakter med lås, för säkert fastsatta hårddiskinstallationer.
Denna högkvalitativa SATA-kabel är framtagen för att kunna ansluta SATA-enheter även i trånga utrymmen.
Power your Internal SATA hard drive from an LP4 connector on your Power Supply
Denna högkvalitativa SATA-kabel är framtagen för att kunna ansluta SATA-enheter även i trånga utrymmen.
Secure latching SATA cable designed for new system boards and SATA hard drives
Make a right side-angled connection to your SATA drive, for installation in narrow spaces
Make a right side-angled connection to your SATA drive, for installation in narrow spaces
Make a Left-Angled Connection to your SATA Drive, for Installation in Tight Spaces
Använd två SATA-enheter med en enda LP4-strömkontakt.
Anslut en IDE-hårddisk till en seriell ATA-strömkontakt
Anslut din SATA-enhet i rät vinkel vid installation i trånga utrymmen
Gör en vänstervinklad anslutning till SATA-enheten vid installationer i trånga utrymmen
Denna högkvalitativa SATA-kabel är framtagen för att kunna ansluta SATA-enheter även i trånga utrymmen.
Make a right-angled connection to your SATA drive, for installation in tight spaces
Make a left side-angled connection to your SATA drive, for installation in narrow spaces
Montera en 2,5 tums SATA-hårddisk i vilken dator som helst med ett ledigt 3,5 tums fack
Montera två 2,5" SATA SSD-/HDD-enheter i ett enda 3,5" enhetsfack
Add two 2.5in SATA hard drives to a single 3.5in drive bay
Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)In order to rebuild a RAID array, you need to replace a physical drive with an identical drive on the same RAID controller. Although standard RAID levels are generally agreed upon throughout the industry, the implementation varies between manufacturers. RAID arrays are typically not accessible when they are moved to another controller, and data may be unrecoverable if the drives are out of order or have been formatted or accessed by another RAID controller.
If a RAID controller has failed, you should get the exact same model of RAID controller.
Note: If a drive or drives were damaged, it is possible that the RAID array may be permanently unrecoverable.
RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, you should back up the data on another physical drive or logical set of drives.
With the following RAID modes, recovery is possible using the same StarTech.com product. Refer to the following table for the appropriate method to use to recover your RAID array.
| RAID mode | Max # of failed drives | Procedure |
| RAID 1 | Only one drive is needed for recovery. |
The array will rebuild and is accessible during the rebuilding process. |
| RAID 3 | Single drive failure will rebuild. |
Note: Do not change the order of the drives.
|
| RAID 5 | Single drive failure will rebuild. |
Note: Do not change the order of the drives.
|
| RAID 10 | Only one drive in a mirrored set can fail. |
Note: Do not change the order of the drives.
|
Note: Not all StarTech.com devices support each of the RAID modes described below. For more information on the RAID modes that your device supports, refer to the manual or the StarTech.com product page.
Redundant Array of Independent Disks (RAID) is a virtual disk technology that combines multiple physical drives into one unit. RAID can create redundancy, improve performance, or do both.
RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, it should be backed up to another physical drive or logical set of drives.
The following are terms that are normally used in connection with RAID:
Different RAID levels exist for different application requirements.
Refer to the following table for the list of RAID modes offered by some StarTech.com products:
| RAID mode | Description | Operation | Advantages | Disadvantages | Recovery |
| RAID 0 | Striped disks | Data is split evenly between two or more disks. | Large size and the fastest speed. | No redundancy. | If one or more drives fails, this results in array failure. |
| RAID 1 | Mirrored disks | Two or more drives have identical data on them. | A single drive failure will not result in data loss. | Speed and size is limited by the slowest and smallest disk. | Only one drive is needed for recovery. |
| RAID 3 | Striped set with dedicated parity | Data is split evenly between two or more disks, plus a dedicated drive for parity storage. | High speeds for sequential read/write operations. | Poor performance for multiple simultaneous instructions. | A single drive failure will rebuild. |
| RAID 5 | Striped disks with distributed parity | Data is split evenly between three or more disks. Parity is split between disks. | Large size, fast speed, and redundancy. | The total array size is reduced by parity. | A single drive failure will rebuild. |
| RAID 10 | 1+0; Striped set of Mirrored Subset | Four or more drives are made into two mirrors that are striped. | Larger size and higher speed than RAID-1, and more redundancy than RAID-0. | No parity. | Only one drive in a mirrored set can fail. |
| JBOD | Just a Bunch Of Disks | Any number of drives are accessed independently by the operating system. | Software RAID modes can be used. | Hardware RAID may have better performance. | N/A |
| Big | Spanning or Concatenation | Data is written on one drive until it is full, and then the next drive(s) until it or they are full. | Creates a very large and simple array. |
No redundancy. |
N/A |
| Clone | RAID 1 + Spare |
Two drives have identical data, plus one drive is used for rebuilding in case of a primary array failure. |
Seamless operation when one drive fails in a RAID-1 array. | Spare drive is not accessible to the user. | Only one drive is needed for recovery. |
