Produkt ID: 35BAYCF2IDE
Compact Flash IDE-adaptern är en perfekt lösning för CompactFlash (CF I, CF II) och IBM Micro Drive-media och ger dig tillgång till flash/micro-drive media som om det var en IDE-hårddisk.
CF/IDE-adaptern kan installeras i chassit med en enkel montering i ett tillgängligt 3,5" enhetsfack för att ansluta till datorns IDE-buss genom antingen en 40- eller 44-stifts-anslutning.
CF IDE-adaptern är designad och tillverkad för att vara en pålitlig mediakortsplattform och täcks av StarTech.coms 2-årsgaranti.
Warranty Information | Warranty | 2 Years |
---|---|---|
Förpackning | Fraktvikt (förpackning) | 215 g [7,6 oz] |
Package Length | 22 cm [8,7 in] | |
Package Width | 48 mm [1,9 in] | |
Package Height | 15,8 cm [6,2 in] | |
Hårdvara | Gränssnitt | IDE |
Kontakt(er) | 1 - Enhetskontakter | CompactFlash-plats (50-stifts) |
1 - Värdkontakter | IDE (40-stifts, EIDE/PATA) | |
SP4 (4-stifts, ström till liten enhet) | ||
Miljö | Drifttemperatur | -55°C to 85°C (-67°F to 185°F) |
Förvaringstemperatur | -55°C to 85°C (-67°F to 185°F) | |
Luftfuktighet | 5% ~ 85% RH | |
Mjukvara | OS-kompatibilitet | Operativsystemsoberoende, varken programvara eller drivrutiner behövs |
Prestanda | Maximal dataöverföringshastighet | 133 MBps |
Minnesmediatyp | CF (Compact Flash I/II-kort) | |
Särskilda anmärkningar/krav | Obs. | Denna produkt stöder inte hot-swapping med flashkort när datorn är på. Datorn måste vara avstängd för att byta kort. |
Utseende | Produktvikt | 129 g [4,6 oz] |
Produktlängd | 97 mm [3,8 in] | |
Produktbredd | 100 mm [3,9 in] | |
Produkthöjd | 25 mm [1,0 in] | |
Vad det är i lådan | 1 - Ingår i paketet | Compact Flash till IDE-adapter |
3,5" kabinett | ||
Helprofil fäste för expansionkort | ||
SP4 till LP4 Molex strömkabel | ||
Instruktionsbok |
Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size
If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.
When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.
There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.
Note: For more information on how to detect an IDE hard drive, visit http://www.startech.com/faq/hard_drive_accessories_ide_detection.
Older IDE drives are not supported by current StarTech.com products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.
There are a number of reasons that older IDE drives may not be detected, including the following:
The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).
The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).
The sector size is not 512 bytes.
Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.