Utgått

3 Drive 3.5in Trayless Hot Swap SATA Mobile Rack Backplane

Hot swap up to three 3.5in SATA hard drives in seconds

Produkt ID: HSB320SATBK

  • Holds up to three SATA drives across two 5.25" bays
  • Trayless design: drives are not mounted into separate trays/enclosures
  • Internal rubber shock absorbers

This 3 Bay SATA Mobile Rack lets you swap between 3.5in SATA hard drives in seconds.

A time saving storage solution, the mobile rack offers three trayless SATA hard drive bays, allowing you to hot swap Serial ATA hard drives but avoid having to mount the drives to trays for deployment or unfasten them for replacement.

To maximize performance and utilize the full speed potential of your SATA III hard drives, this HDD Backplane supports SATA III for transfer speeds up to 6 Gbps when paired with a compatible controller.

Supporting up to three hard drives, the mobile SATA hot swap rack only takes up two 5.25in drive bays inside a host computer - maximizing space-efficiency within the computer. With support for SATA HDD speeds up to 6.0 Gbps, the mobile rack/backplane is fully compatible with RAID installations to ensure maximum performance and versatility for enhanced storage applications.

Using Terabyte hard drives? Don’t expose your Hard Drive and valuable data to unnecessary heat!
The HSB320SATBK has two built-in 40mm fans that re-distribute the heat build-up generated as a result of typical drive operation. This feature is especially important for larger volume storage drives, and faster “spinning" drives (i.e 7200 RPM), as it can help optimize drive operability and in turn preserve stored data integrity.
 

Användning

  • Imaging - For System Builders or configuring new systems - Use Hot Swap Bay in master system to copy Windows OS quickly to multiple blank hard drives as part of system building process
  • IT environments where just need to quickly insert/replace removable hard drive - no protection required for mobility reasons for hard drive
  • Serial ATA servers and storage subsystems
  • High-end workstations
  • Serial ATA Drive Arrays
  • Network Attached Storage
  • Enterprises replacing IDE/Parallel ATA hard drives with SATA hard drives

Fördelarna med StarTech.com

  • Quickly and easily install or remove hard drives without having to open the chassis with the innovative trayless design
  • Rubber shock absorbers, a solid aluminum construction and 10,000+ insertion rating ensures longevity from both the drives and bay
  • Maximize performance, with file transfer speeds up to 6Gbps when paired with SATA III HDD and controller

Partnernummer

  • UPC 065030821711

Kompatibilitet

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Length 26,8 cm [10,6 in]
Package Width 14,3 cm [5,6 in]
Package Height 21,8 cm [8,6 in]
Fraktvikt (förpackning) 1,6 kg [3,6 lb]
Hårdvara Antal enheter 3
Enhetsstorlek 3.5in
Enhetstyp SATA
2 - Flaktar 40 mm
Indikatorer 3 - LED-indikatorer Drive Power
Drive Activity
Kontakt(er) 3 - Enhetskontakter SATA (7-stifts, data)
SATA-ström (15-stifts)
3 - Värdkontakter SATA (7-stifts, data)
SATA-ström (15-stifts)
Miljö Drifttemperatur 0°C to 50°C (32°F to 122°F)
Förvaringstemperatur 0°C to 50°C (32°F to 122°F)
Luftfuktighet Operating - 5~85% RH Non-condensing
Storage - 5~95%
Mjukvara OS-kompatibilitet OS independent; No software or drivers required
Prestanda Hot swap-förmåga Ja
Inlänkningshastighet 10, 000+ Cycles
Bullernivå 24 dBA
Utseende Färg Svart
Kabinettyp Aluminium och plast
Produktlängd 19,4 cm [7,6 in]
Produktbredd 14,6 cm [5,7 in]
Produkthöjd 8,5 cm [3,3 in]
Produktvikt 1,1 kg [2,4 lb]
Vad det är i lådan 1 - Ingår i paketet 5.25" Tray-Less SATA Hot-Swap Bay
Screw kit
Instruction Manual
3 - Ingår i paketet SATA cable
SATA to LP4 Molex + LED Cable

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

When you troubleshoot issues with a hard drive rack, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • SATA and SAS cables
  • Hard drives
  • Hard drive rack

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive rack in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive rack in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive rack, it is recommended that you do the following:

  • To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter.  Check to see if your hard drive is listed.
  • If the hard drive is listed with unallocated space, it needs to be formatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.

  • If the hard drive is listed as healthy but does not have a drive letter assigned to it, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Vänta...
Tillbaka till toppen