Produkt ID: IDE2SAT2
IDE2SAT2 adaptern för anslutning mellan 40 stifts IDE och SATA låter dig ansluta en SATA I/II/III-enhet till en tillgänglig IDE/ATA 33/66/100/133-moderkortsport - en kostnadseffektiv lösning som låter dig lägga till nyare SATA-enheter och behålla ditt befintliga moderkort.
IDE/SATA-adaptern är en kostnadseffektiv lösning för att ansluta en nyare 2,5"/3,5"/5,25" SATA-enhet till en äldre IDE-moderkortsport. IDE2SAT2 har även stöd för ODD (Optical Disk Drive) och låter dig lägga till Blu-ray-, DVD- eller CD-ROM-enheter till ett äldre IDE-moderkort.
IDE/SATA-adaptern täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.
Warranty Information | Warranty | 2 Years |
---|---|---|
Förpackning | Package Height | 33 mm [1,3 in] |
Package Length | 14,5 cm [5,7 in] | |
Fraktvikt (förpackning) | 89 g [3,1 oz] | |
Package Width | 17,5 cm [6,9 in] | |
Hårdvara | Gränssnitt | IDE |
Antal enheter | 1 | |
Enhetsstorlek | 2.5in & 3.5in | |
Enhetstyp | SATA | |
Chipset-ID | Marvell - 88SA8052 | |
Kontakt(er) | 1 - Kontakttyp(er) | SP4 (4-stifts, ström till liten enhet) |
IDE (40-stifts, EIDE/PATA) | ||
SATA data- & ström-kombo (7+15-stifts) | ||
Miljö | Drifttemperatur | 5°C to 50°C (40°F to 122°F) |
Förvaringstemperatur | -25°C to 80°C (-13°F to 176°F) | |
Luftfuktighet | 15~90% RH | |
Mjukvara | OS-kompatibilitet | OS independent; No software or drivers required |
Prestanda | Maximal dataöverföringshastighet | 133 MB/s |
RAID | Nej | |
Särskilda anmärkningar/krav | System- och kabelkrav | En IDE-kontroller och ATA-kabel (ingår ej) |
Utseende | Produktvikt | 29 g [1,0 oz] |
Kabinettyp | Stål | |
Produktlängd | 75,5 mm [3,0 in] | |
Produktbredd | 20 mm [0,8 in] | |
Produkthöjd | 23 mm [0,9 in] | |
Vad det är i lådan | 1 - Ingår i paketet | IDE till SATA-adapter |
LP4 Molex till SP4 strömkabel | ||
Instruktionsbok |
Anslut två LP4-enheter (CD/DVD-ROM-enheter etc.) till en enda LP4-kontakt
Omvandlar i stort sett alla 2,5 tums SATA- och SAS-hårddiskar till en 3,5 tums SATA-hårddisk
Montera en 3,5 tums hårddisk i vilken stationär dator som helst med ett tillgängligt 5,25 tums fack
Connect two ATA 100/133 drives to a computer IDE controller
Connect two hard drives to a computer IDE controller
Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size
If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.
When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.
There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.
Note: For more information on how to detect an IDE hard drive, visit http://www.startech.com/faq/hard_drive_accessories_ide_detection.
Older IDE drives are not supported by current StarTech.com products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.
There are a number of reasons that older IDE drives may not be detected, including the following:
The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).
The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).
The sector size is not 512 bytes.
Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.