Produkt ID: S251BU31C3CB
Här är ett bra sätt att lägga till supersnabb, superbärbar datalagring till din USB-C™-kapabla surfplatta eller bärbara dator, inklusive MacBook, Chromebook Pixel™ och Dell XPS 12. Detta USB 3.1 Gen 2-hårddiskkabinett har en inbyggd USB-C-kabel som gör det enkelt att ansluta en 2,5" SATA-hårddisk (HDD) eller -solid state-enhet (SSD) till din dator genom dess USB-C-port.
Bärbar lagring med en inbyggd USB-C-kabel
Detta bärbara hårddiskkabinett gör om din 2,5" SATA solid state-enhet eller hårddisk till extern datalagring som är enkel att ta med sig. Dess kompakta och lätta design får enkelt plats din datorväska.
För att maximera bärbarheten har kabinettet en inbyggd USB-C-kabel så att du aldrig behöver oroa dig för att glömma att ta med dig din anslutningskabel var du än går. Kabeln viras säkert runt kabinettet när det inte används för att förhindra skador eller trassel och tar upp mindre plats i datorväskan. USB Type-C™-kontakten är liten och vändbar vilket ger enklare inkopplingar och mindre risk för portskador. Hårddiskkabinettet är USB-drivet och ingen extern strömadapter behövs, vilket innebär en sak mindre att ta med sig.
Superhöga dataöverföringshastigheter
Hårddiskkabinettet ansluts enkelt till USB-C-porten på din bärbara dator eller surfplatta så att du kan nå och lagra filer snabbare än någonsin. Med detta USB 3.1 Gen 2-hårddiskkabinett kan du utnyttja den höga prestandan från de senaste SSD-enheterna och hårddiskarna. Det stöder dataöverföringshastigheter på upp till 10 Gbps - dubbelt så snabbt som USB 3.0-teknik (USB 3.1 Gen 1).
Hårddiskkabinettet stöder SATA I, II och III (upp till 6 Gbps) och dessutom UASP för förbättrad prestanda.
Slimmad design i hållbart aluminium
Kabinettet är tillverkad med ett slimmat och hållbart aluminiumhölje och är väl rustat att hålla din data säker var du än går. Aluminiumhöljet hjälper dessutom till med att fördela värme för att underlätta värmeavledning.
S251BU31C3CB täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.
Warranty Information | Warranty | 2 Years |
---|---|---|
Förpackning | Package Height | 41,0 mm [1,6 in] |
Package Length | 18,9 cm [7,4 in] | |
Fraktvikt (förpackning) | 226,0 g [8,0 oz] | |
Package Width | 15,3 cm [6,0 in] | |
Hårdvara | Gränssnitt | USB 3.1 Gen 2 |
Busstyp | USB 3.1 Gen 2 | |
Antal enheter | 1 | |
Enhetsstorlek | 2.5in | |
Enhetstyp | SATA | |
Enhetsinstallation | Fixerad | |
Stödda enhetshöjd(er) | 5mm | |
Fläkt(ar) | Nej | |
Stödda enhetshöjd(er) | 7mm | |
9.5mm | ||
Chipset-ID | ASMedia - ASM1351 | |
Indikatorer | 1 - LED-indikatorer | Ström och aktivitet |
Kontakt(er) | 1 - Kontakttyp(er) | USB Type-C (24-stifts) USB 3.1 (10 Gbps) |
1 - Enhetskontakter | 22 pin SATA Data + Power (7 + 15 pin) Plug | |
1 - Värdkontakter | USB Type-C (24-stifts) USB 3.1 (10 Gbps) | |
Miljö | Drifttemperatur | 0°C to 40°C (32°F to 104°F) |
Förvaringstemperatur | -10°C to 65°C (14°F to 149°F) | |
Luftfuktighet | Luftfuktighet vid användning: 10% ~ 90% RH
Luftfuktighet vid förvaring: 5% ~ 95% RH |
|
Mjukvara | OS-kompatibilitet | OS independent; No software or drivers required |
Prestanda | Maximal dataöverföringshastighet | 10 Gbps |
Typ och hastighet | USB 3.1 Gen 2 - 10 Gbit/s | |
UASP-stöd | Ja | |
4Kn Support | Ja | |
Typ och hastighet | SATA III (6 Gbps) | |
TRIM Support | Ja | |
Maximal enhetskapacitet | För närvarande testad med hårddiskar på upp till 2 TB vid 7200 RPM | |
Medeltid mellan fel (MTBF) | 100000 | |
Särskilda anmärkningar/krav | Obs. | Windows 7 and earlier Windows versions do not support TRIM with USB to SATA devices. |
Utseende | Färg | Svart |
Kabinettyp | Aluminium och plast | |
Kabellängd | 27,3 cm [10,7 in] | |
Maximal enhetshöjd | 9,5 mm [0,4 in] | |
Produktlängd | 13,9 cm [5,5 in] | |
Produktbredd | 82,8 mm [3,3 in] | |
Produkthöjd | 15,4 mm [0,6 in] | |
Produktvikt | 126,0 g [4,4 oz] | |
Vad det är i lådan | 1 - Ingår i paketet | USB 3.1 2,5" SATA SSD/HDD-kabinett med USB-C-kabel |
3 - Ingår i paketet | monteringsskruvar för kabinett | |
hårdvaruskruvar för hårddiskmontering | ||
1 - Ingår i paketet | Skruvmejsel | |
Snabbinstallationsguide |
Uppgradera din dator till 10 Gbps-hastighet med USB 3.1 Gen 2 genom att lägga till två USB Type-C-portar
Uppgradera din dator till 10 Gbps-hastighet med USB 3.1 Gen 2 genom att lägga till både USB Type-C- och USB Type-A-portar
Gör om en USB Type-C-port på din bärbara dator till tre USB Type-A-portar (5 Gbps) och en USB Type-C-port
Gör om en USB Type-C-port på din bärbara dator till tre USB Type-A-portar för laddning och synkning (5 Gbps) och en USB Type-C-port
Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)When you troubleshoot issues with a hard drive enclosure, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:
To test your setup components, try the following:
When you test the hard drive and hard drive enclosure, it is recommended that you do the following:
Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.
Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.
If your setup components support USB 3.1 but you are experiencing slower transfer speeds than you expected, consider the following:
To confirm the functionality of your USB host connection, its ports, and any other devices in your setup, refer to the information provided by the manufacturer.
Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.
Du bör inte uppgradera enhetens inbyggda programvara om du inte har några problem med enhetens funktioner. Du behöver bara uppgradera om du har problem med enheten och är säker på att problemet är den inbyggda programvaran. Du kan bekräfta detta genom att läsa igenom den medföljande dokumentationen eller kontakta vår tekniska avdelning. Felaktig uppgradering av inbyggd programvara kan resultera i minskade prestanda så vi rekommenderar att du kontaktar StarTech.com först.
Yes, this device supports the TRIM command. If the OS issues a TRIM command, the command will be passed to the connected device.
To determine if your hard drive will work in this enclosure, on the product page, click the Technical Specifications tab, and do the following:
USB 3.1 is the most recent version of the USB (Universal Serial Bus) standard for connecting computers and electronic devices. It is capable of data transfer speeds up to 10Gbps, and while it can use the USB-C connector type, it can also use a variety of other connector types. To achieve USB 3.1 transfer speeds, your USB host connection, cables, and device must all support USB 3.1. USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps).
USB 3.0 is capable of data transfer speeds up to 5Gbps. USB 3.0 is also known as USB 3.1 Gen 1 (5Gbps).
USB 3.1 is backwards compatible with USB 3.0 and USB 2.0, except in the following scenarios:
To transfer data at speeds of 10Gbps, you need to confirm that the following components in your setup support USB 3.1:
Note: USB 3.1 is also known as USB 3.1 Gen 2 (10Gbps). Devices that support USB 3.1 should have the USB 3.1 symbol on them. If the USB 3.1 symbol does not appear on your USB source or device, refer to the information provided by the manufacturer to confirm whether the USB source or device support USB 3.1.
The included USB cable for this USB 3.1 Gen 2 device has been tested and verified to perform at USB 3.1 Gen 2 speeds of 10Gbps.
USB-C is a type of USB connector that is capable of supporting the following:
If using Thunderbolt 3 over USB-C, the connection is capable of additional features. For example, Thunderbolt 3 is capable of 40Gbps of total bandwidth. For more information, refer to the following FAQ: https://www.startech.com/faq/thunderbolt-3-port-capabilities.
Not all USB-C ports or devices are capable of supporting all of the features listed above, or all of the features at the maximum capabilities. If you require a specific USB-C feature, your USB host connection, cables, and device must all support the feature that you require. For more information about whether your components support specific USB-C features, refer to the information provided by the manufacturers.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).
Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.
Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.
Navigate to Disk Management.
When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.
Click OK.
Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.
Right-click Unallocated or RAW volume, and select New Simple Volume.
In the New Partition Wizard, click Next.
Select Primary partition.
Leave the partition size set to default, and click Next.
Assign a drive letter or leave it set to the default, and click Next.
Enter the following settings to format the partition:
The new drive should appear in Windows Explorer.
Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).
Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.
Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.
To create a partition on a new drive, complete the following:
Open Finder.
Navigate to Applications and click Utilities.
Open Disk Utility.
Select the new drive and click the Partition tab.
Click Options and verify that it is set to GUID Partition Table.
Enter a name for the partition.
Click Partition.
The drive should now be accessible in Finder.