USB 3.0/eSATA-kabinett med 4 fack och inbyggd HDD-fläkt & UASP för 3,5" SATA III-hårddiskar – SATA 6 Gbps

Lägg till fyra 3,5" SATA III-hårddiskar till datorn externt genom USB 3.0 med UASP eller eSATA

Produkt ID: S3540BU33E

  • Stöder SATA III (6 Gbps) och UASP (5 Gbps) för optimal prestanda
  • Kompatibel med SATA-hårddiskar revision I/II/III (1,5/3,0/6,0 Gbps)
  • Kompatibel med USB 3.0/2.0/1.1 (5 Gbps / 480 Mbps / 1,5 Mbps)
Ditt pris
€187,99 EUR excl. VAT
€234,99 EUR incl. VAT

S3540BU33E kabinettet med 4 fack låter dig installera fyra 3,5” SATA-hårddiskar i ett externt kabinett och ansluta till datorn genom USB 3.0 eller eSATA.

För snabb prestanda och effektiva dataöverföringar stöder kabinettet SATA III-överföringshastigheter - upp till 6 Gbps vid anslutning genom eSATA. Detta mångsidiga kabinett kan även anslutas genom USB 3.0, med stöd för UASP och med upp till 70 % snabbare prestanda än vanlig USB 3.0 vid användning med en UASP-kapabel värdkontroller. Se våra UASP-testresultat nedan för mer information.

S3540BU33E täcks av StarTech.coms 2-årsgaranti och gratis livstidsgaranti på teknisk support.

Förbättrad prestanda med UASP

UASP stöds av Windows 8, Mac OSX (10.8 eller senare) och Linux. Vid tester ger UASP 70 % snabbare läshastigheter och 40 % snabbare skrivhastigheter över vanlig USB 3.0.

UASP Speed Diagram

Samtidigt visade UASP-testerna på 80 % reducerad åtgång av processorns resurser.

UASP Speed Diagram

Testerna utfördes med ett Intel® Ivy Bridge-system, ett UASP-kapabelt kabinett från StarTech.com och en SATA III solid state-enhet.

Användning

  • Använd externa hårddiskar för högpresterande tillämpningar som videoredigering eller fotografi
  • Skapa en extern säkerhetskopia av viktig data
  • Bygg en extern mjukvaru-RAID-array
  • Få mer lagringsutrymme på den stationära eller bärbara datorn genom en extern eSATA-anslutning

Fördelarna med StarTech.com

  • Mångsidiga anslutningsalternativ genom antingen USB eller eSATA
  • Maximera prestandan med filöverföringshastigheter på upp till 6 Gbps använda eSATA
  • Håll enheterna svala med en inbyggd fläkt

Partnernummer

  • UPC 065030858045

Kompatibilitet

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Height 19,7 cm [7,8 in]
Package Length 28,2 cm [11,1 in]
Package Width 22,2 cm [8,7 in]
Fraktvikt (förpackning) 2,2 kg [4,9 lb]
Hårdvara Busstyp USB 3.0
Gränssnitt USB 3.0 & eSATA
Antal enheter 4
Enhetsstorlek 3.5in
Enhetstyp SATA
Enhetsinstallation Fixerad
Antal interna 3,5 tums fack 4
Fläkt(ar) Ja
1 - Flaktar 80 mm
Chipset-ID JMicron - JMS567
JMicron - JMB575
Indikatorer 1 - LED-indikatorer Ström-LED
4 - LED-indikatorer LED för HDD-aktivitet
Kontakt(er) 4 - Enhetskontakter SATA data- & ström-kombo (7+15-stifts)
1 - Värdkontakter eSATA (7-stifts, data)
Miljö Drifttemperatur 5°C to 35°C (41°F to 95°F)
Förvaringstemperatur -20°C to 50°C (-4°F to 122°F)
Luftfuktighet 20 ~ 80 % RH
Mjukvara OS-kompatibilitet OS independent; No software or drivers required
Prestanda Maximal dataöverföringshastighet 6 Gbps (eSATA)
5 Gbps (USB 3.0)
Typ och hastighet USB 3.0 - 5 Gbit/s
UASP-stöd Ja
Typ och hastighet SATA III (6 Gbps)
Port Multiplier Ja
RAID Nej
Maximal enhetskapacitet För närvarande testad med hårddiskar på upp till 6 TB 7200 RPM
Hot swap-förmåga Nej
Allmänna specifikationer Stöder 2,5" solid state-enheter (SSD) och hårddiskar (HDD) med en 2,5" till 3,5" hårddiskadapter som till exempel 25SAT35HDD & 25SATSAS35
Ström Power Source AC-adapter medföljer
Inspänning 100 - 240 AC
Inström 2.5 A
Utspänning 12V DC
Utström 6.5 A
Strömförbrukning 78
Utseende Produktlängd 20,0 cm [7,9 in]
Produktbredd 11,4 cm [4,5 in]
Produkthöjd 14,3 cm [5,6 in]
Produktvikt 1,0 kg [2,3 lb]
Vad det är i lådan 1 - Ingår i paketet USB 3.0/eSATA-kabinett med 4 fack för 3,5" SATA-hårddiskar
eSATA-kabel
USB 3.0-kabel
Universell strömadapter (NA/UK/EU)
Instruktionsbok

Tillbehör

Utgått
PEXUSB3S2

PCI Express SuperSpeed USB 3.0-kortadapter med 2 portar och UASP-stöd

Lägg till två USB 3.0-portar till din stationära dator genom en PCI Express-utbyggnadskortplats

Ditt pris
€34,99 EUR excl. VAT
€43,74 EUR incl. VAT
Utgått
PEXESATA1

1 Port PCI Express eSATA II Controller Card

Add an eSATA port to a desktop computer through a PCI Express slot

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
PEXUSB3S4

SuperSpeed USB 3.0 PCI Express-kort med 4 portar och UASP - SATA-ström

Lägg till fyra USB 3.0-portar till din stationära dator genom en PCI Express-utbyggnadskortplats

Ditt pris
€50,99 EUR excl. VAT
€63,74 EUR incl. VAT
Utgått
MPEXUSB3S2

2 Port Mini PCI Express SuperSpeed USB 3.0 Card Adapter with UASP Support

Add 2 USB 3.0 ports through a mini PCI Express slot

Ditt pris
€46,46 EUR excl. VAT
€58,08 EUR incl. VAT
Utgått
PCIUSB3S2

2 Port PCI SuperSpeed USB 3.0 Card Adapter

Add 2 USB 3.0 ports to a desktop computer through a PCI slot

Ditt pris
€72,10 EUR excl. VAT
€90,13 EUR incl. VAT
ECUSB3S254F

54 mm flush mount ExpressCard SuperSpeed USB 3.0-kortadapter med 2 portar

Lägg till två flush mount USB 3.0-portar till en ExpressCard-kompatibel bärbar dator

Ditt pris
€59,99 EUR excl. VAT
€74,99 EUR incl. VAT
Utgått
ECUSB3S1

1 Port Flush Mount ExpressCard SuperSpeed USB 3.0 Card Adapter with UASP Support

Flush mount a USB 3.0 ExpressCard adapter into a laptop ExpressCard slot

Ditt pris
€22,46 EUR excl. VAT
€28,08 EUR incl. VAT
PEXUSB3S11

PCI Express SuperSpeed USB 3.0-kort med 2 portar och UASP-stöd - 1 Intern, 1 extern

Lägg till en intern och en extern SuperSpeed USB 3.0 till din dator

Ditt pris
€44,99 EUR excl. VAT
€56,24 EUR incl. VAT
Utgått
PEXESATA2

2 Port PCI Express eSATA Controller Adapter Card

Add 2 eSATA ports to your desktop computer through a PCI Express expansion slot

Ditt pris
€25,99 EUR excl. VAT
€32,49 EUR incl. VAT
Utgått
PEXESATA2I

1 Port eSATA + 1 Port SATA II PCI Express SATA Controller Card

Add an internal SATA port and an external SATA (eSATA) port to your desktop computer through a PCI Express expansion slot

Ditt pris
€24,82 EUR excl. VAT
€31,03 EUR incl. VAT
Utgått
ECESATUSB1

1 Port ExpressCard Power eSATA Controller Adapter Card

Add an eSATAp (eSATA + USB 2.0) port to a computer through an ExpressCard slot

Ditt pris
€16,99 EUR excl. VAT
€21,24 EUR incl. VAT
Utgått
ECESATA22

2 Port ExpressCard eSATA Controller Adapter Card

Add 2 eSATA ports through your laptop ExpressCard slot

Ditt pris
€43,24 EUR excl. VAT
€54,05 EUR incl. VAT
Utgått
CBESAT2

2 Port CardBus eSATA Laptop Controller Adapter Card

Adds 2 eSATA ports to a laptop through a CardBus slot

Ditt pris
€9,99 EUR excl. VAT
€12,49 EUR incl. VAT
ESATA3

3 ft Shielded External eSATA Cable M/M

Connect your external SATA storage devices to your Laptop or desktop.

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
ESATA6

1,8 m skärmad extern eSATA-kabel M/M

Anslut dina externa SATA-lagringsenheter till din bärbara eller stationära dator.

Ditt pris
€10,99 EUR excl. VAT
€13,74 EUR incl. VAT
SVA12DN4NEUA

DC-strömadapter - 12 V, 6,5 A

Byt ut din borttappade eller trasiga strömadapter

Ditt pris
€50,99 EUR excl. VAT
€63,74 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

SATA hard drive controllers require a feature called port multiplier to read more than one hard drive per SATA or eSATA port. The port multiplier feature is not standard on many SATA hard drive controllers.

If your computer is only recognizing one of your hard drives, you need to plug the eSATA cable into a SATA controller that includes the port multiplier feature. If none of your current hard drive controllers include this feature, you can add a hard drive controller that does support port multiplier in any available expansion slot (for example, PCI, PCI-Express, PCMCIA, CardBus, or ExpressCard). StarTech.com has hard drive controllers available that support the port multiplier feature. To view the hard drive controllers, click here: http://startech.com/Cards-Adapters/HDD-Controllers/SATA-Cards/?filter_PORTMULTIPLIER=Yes.

If you have a hard drive controller card that does support the port multiplier feature but it is only reading one hard drive at a time, update the drivers of the hard drive controller. To find the most current StarTech.com drivers, click here: http://www.startech.com/Support.

When you troubleshoot issues with a hard drive enclosure, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • Cables
  • Hard drives
  • Hard drive enclosure

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive enclosure in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive enclosure in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive enclosure, it is recommended that you do the following:

  • To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive.​

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

Hur man

To confirm that the Mac OS detects your USB device, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your USB device is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

You may need to refresh the System Information page after you plug in your device.  To do so, press Command R with the System Information page open.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Before You Buy

To determine if your hard drive will work in this enclosure, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the enclosure supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the enclosure was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the enclosure. For example, IDE, SATA, or M.2.
  • Make sure that the enclosure supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Make sure that the enclosure supports the height of your hard drive. For example, 9 mm or 15 mm.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the enclosure. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the enclosure.

Hard Drives

Windows 10 

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).

Initialize a drive

Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.

  1. Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.

  2. Navigate to Disk Management.

  3. When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.

  4. Click OK.

Create a partition in a drive

Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.

  1. Right-click Unallocated or RAW volume, and select New Simple Volume.

  2. In the New Partition Wizard, click Next.

  3. Select Primary partition.

  4. Leave the partition size set to default, and click Next.

  5. Assign a drive letter or leave it set to the default, and click Next.

  6. Enter the following settings to format the partition:

  • In the File System field, enter NTFS.
  • Set the Allocation unit size to Default.
  • In the Volume label field, enter <your name/reference>.
  • Select the Perform a quick format check box.
  • Clear the Enable file and folder compression check box.
  1. Click Next > Finish.

The new drive should appear in Windows Explorer.

Mac OS

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).

Initialize a drive

Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.

Create a partition on a drive

Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.

To create a partition on a new drive, complete the following:

  1. Open Finder.

  2. Navigate to Applications and click Utilities.

  3. Open Disk Utility.

  4. Select the new drive and click the Partition tab.

  5. Click Options and verify that it is set to GUID Partition Table.

  6. Enter a name for the partition.

  7. Click Partition.

The drive should now be accessible in Finder.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Tillbaka till toppen
Vänta...