Produkt ID: SAT2IDEADP
SAT2IDEADP SATA till IDE-hårddiskadapter gör att du kan använda 2,5/3,5 tums IDE baserade hårddiskar (PATA) i de flesta StarTech.coms SATA-baserade HDD-dockningsstationer och hårddiskduplikatorer. SATA-IDE-adaptern är tillverkad helt i metall för att säkerställa lång livslängd och är helt kompatibel med IDE-hårddiskar upp till ATA-133 (133 Mbps).
SATA/IDE-adapterns unika monteringsdesign gör att det går snabbt att installera den på en IDE/ATA-hårddisk och placera den i en SATA-hårddiskdocka vilket gör det snabbt och smidigt att hämta data från äldre HDD:er. Adaptern kan även användas till att installera IDE-hårddiskar i stationära datorer med endast SATA eller om man behöver ansluta en IDE-hårddisk via seriell ATA.
SAT2IDEADP hårddiskadapter fungerar med de flesta av StarTech.coms SATA HDD-dockningsstationer och -duplikatorer.
Täcks av StarTech.coms 2 års-garanti och gratis livstidsgaranti på teknisk support.
Warranty Information | Warranty | 2 Years |
---|---|---|
Förpackning | Package Height | 52 mm [2.0 in] |
Package Length | 14.7 cm [5.8 in] | |
Fraktvikt (förpackning) | 218 g [7.7 oz] | |
Package Width | 11 cm [4.3 in] | |
Hårdvara | Antal enheter | 1 |
Enhetsstorlek | 2.5in & 3.5in | |
Enhetstyp | IDE (ATA) | |
Enhetsinstallation | Fixerad | |
Fläkt(ar) | Nej | |
Chipset-ID | JMicron - JM20330 | |
LBA-stöd | 48-bit | |
Kontakt(er) | 1 - Kontakttyp(er) | SP4 (4-stifts, ström till liten enhet) |
1 - Enhetskontakter | LP4 (4-stift, Molex-type Large Drive Power) | |
IDE (44-stifts, EIDE/PATA, 2,5" HDD) | ||
IDE (40-stifts, EIDE/PATA) | ||
1 - Värdkontakter | SATA-ström (15-stifts) | |
SATA (7-stifts, data) | ||
Miljö | Drifttemperatur | 5°C to 80°C (41°F to 176°F) |
Förvaringstemperatur | -40°C to 70°C (-40°F to 158°F) | |
Luftfuktighet | 8% ~ 90% RH | |
Mjukvara | OS-kompatibilitet | OS independent; No software or drivers required |
Prestanda | RAID | Nej |
Utseende | Produktvikt | 104 g [3.7 oz] |
Färg | Svart | |
Kabinettyp | Stål | |
Produktlängd | 10.1 cm [4.0 in] | |
Produktbredd | 78 mm [3.1 in] | |
Produkthöjd | 26 mm [1.0 in] | |
Vad det är i lådan | 1 - Ingår i paketet | SATA till IDE-adapter |
40 stifts IDE-kabel | ||
SP4 till LP4-strömkabel | ||
40 stifts till 44 stifts IDE-kabel med ström | ||
Förpackning med monteringsskruvar | ||
Instruktionsbok |
Skapa en exakt kopia av en 2,5 tums eller 3,5 tums SATA-hårdisk till en annan, utan ansträngning och utan dator
Få snabb tillgång till fyra 2,5"/3,5" SATA HDD över USB 3.0 eller eSATA
Enable quick access to four 2.5”/3.5” SATA HDD from multiple computers
Möjliggör snabb växlingsbar åtkomst till din 2,5 tums- eller 3,5 tums-hårddisk via USB 3.0
Easily connect and swap a 2.5in or 3.5in SATA hard drive through USB
Easily connect and swap a 2.5in or 3.5in SATA hard drive through USB or eSATA
Anslut både en IDE- och SATA-hårddisk till en dator genom USB 2.0
Klona en kombination av 2,5" eller 3,5" IDE- eller SATA-hårddiskar
Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Vi är alltid redo att hjälpa dig med alla dina frågor.
Direktchatt (opens in new window)Note: If you are using an IDE hard drive 1 Gigabyte in size or smaller, refer to the following FAQ: http://www.startech.com/faq/hard_drive_accessories_minimum_ide_hard_drive_size
If you are unable to detect your IDE (PATA) drive using a StarTech.com product, you may need to change the jumper settings on your drive. The jumpers switch the drive between Master, Slave, and Cable Select for most drives. A jumper is a small plastic piece that slides on top of two pins to electrically short them together.
When it does not mention what IDE drive configuration is required or if there is only one drive in the setup, the drive should be configured as Master. If Master is not working, try using the drive in Cable Select.
There is no standard position for the jumpers on IDE drives. On some drives, the jumper diagram is on the label that is on the top of the drive. On other drives, there are markings on the circuit board for CS, MA, and SL, which means a jumper shorts the pins vertically in that position. For more information, refer to the documentation provided by the manufacturer.
Note: For more information on how to detect an IDE hard drive, visit http://www.startech.com/faq/hard_drive_accessories_ide_detection.
Older IDE drives are not supported by current StarTech.com products. Typically, these drives were made earlier than the mid-to-late 1990s and are smaller than 1 Gigabyte in size.
There are a number of reasons that older IDE drives may not be detected, including the following:
The drive uses PIO (Programmed Input/Output) mode and not DMA (Direct Memory Access).
The drive is non-ATA or is using an ATA mode that predates the chipset's compatibility (usually older than ATA-4).
The sector size is not 512 bytes.
Unfortunately there is no workaround in these situations. An older system or an older IDE controller card must be used to access older IDE drives.