Produktsökning
Utgått

Dockningsstation för SATA-hårddisk-duplikator - eSATA USB

Skapa en exakt kopia av en 2,5 tums eller 3,5 tums SATA-hårdisk till en annan, utan ansträngning och utan dator

Produkt ID: SATDOCK22RE

  • Fristående sektor till sektorkopiering, inklusive HPA
  • LED-förloppsindikator som visar dupliceringsstatus
  • Knappväxling mellan hårddiskduplikatorläge och dockningsstationsläge

Med SATDOCK22RE USB och eSATA-dockningsstation för hårddiskduplikator kan du duplicera/klona befintliga hårddiskar utan att använda ett värddatorsystem. Den kan även kopplas till ett datorsystem och användas som extern hårddiskdocka.

Som hårddiskduplikator kan du skapa en exakt 1 till 1 sektorklon från en hårddisk till en annan, inklusive partition- och startsektorinformation, med en hastighet på 72 MB/sekund – vilket säkerställer fullständig data och konsekvens vid känsliga operationer som dataåterställning.

Som extern hårddiskdocka stödjer duplikatorn/dockningsstationen plug-and-play-installation och ansluts till datorn via USB 2.0 eller eSATA, vilket ger dataöverföringshastigheter på upp till 480 Mbps respektive 3 Gbps, från hårddiskarna till ditt datorsystem. Enheter med hög kapacitet (testad med upp till 4 TB 3,5"- och 1 TB 2,5"-enheter per fack) kan användas för att förbättra datorns lagrings/kopieringsmöjligheter.

Att inte behöva installera hårddiskar i ett kabinett eller system för hårddiskbrickor gör installationen snabb – en perfekt lösning för situationer när man måste växla mellan flera hårddiskar. Detta tillsammans med att det inte behövs några särskilda program eller drivrutiner ger en smidig och mångsidig lagringslösning. Värdet på dockningsstationen kan höjas med en SAT2IDEADP (SAT2IDEADP) som gör så att du kan använda en 2,5"- eller 3,5"-IDE-hårddisk i ett fack för SATA-hårddiskar.

Användning

  • Disksektor-spegling/kloning för att skapa en exakt kopia av källdiskten på en annan hårddisk.
  • Skapa identiska säkerhetskopior när det är av yttersta vikt att datan är komplett, som till exempel vid dataåterställning och rättsapplikationer.
  • Perfekt för tekniker som behöver åtkomst till hårddiskar för säkerhetskopiering/återställning eller som regelbundet växlar mellan olika hårddiskar.
  • Snabb dataåtkomst från en hårddisk utan att behöva installera den i chassit eller i ett kabinett.

Fördelarna med StarTech.com

  • Fristående duplikator med LED-förloppsindikator gör det möjligt att skapa 1:1-kopior av hårddiskar utan att ansluta till värddatorn.
  • Supersnabb växling från duplikator till USB 2.0- eller eSATA-anslutning med endast en knapptryckning gör att anslutna datorsystem kan läsa/skriva till hårddiskarna.
  • Designen med toppmatning och den unika utmatningsmekanismen ger snabb och enkel åtkomst till datan utan att man behöver installera hårddiskarna i ett kabinett eller en hårddiskbricka.

Partnernummer

  • UPC 065030840729

Kompatibilitet

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Length 18,5 cm [7,3 in]
Package Width 12 cm [4,7 in]
Package Height 21 cm [8,3 in]
Fraktvikt (förpackning) 820 g [28,9 oz]
Hårdvara Gränssnitt USB 2.0 & eSATA
Antal enheter 2
Enhetsstorlek 2.5in & 3.5in
Enhetstyp SATA
Chipset-ID JMicron - JMB352U
Indikatorer 1 - LED-indikatorer Strömindikator (blå)
Förloppsindikator (blå)
Lägesindikator (blå – JBOD, röd – duplicering)
2 - LED-indikatorer Hårddiskstatus (blå – hårddisk inaktiverad, röd ingen hårddisk har upptäckts, blinkande röd – aktivitet)
Kontakt(er) 2 - Enhetskontakter SATA data- & ström-kombo (7+15-stifts)
1 - Värdkontakter USB B (4-stifts)
eSATA (7-stifts, data)
Miljö Drifttemperatur 5°C to 80°C (41°F to 176°F)
Förvaringstemperatur -40°C to 70°C (-40°F to 158°F)
Luftfuktighet 8~90 % RH
Mjukvara OS-kompatibilitet OS independent; No software or drivers required
Prestanda Typ och hastighet USB 2.0 - 480 Mbit/s
SATA II (3 Gbps)
Maximal enhetskapacitet För närvarande testad med upp till 4 TB 5400 RPM-hårddiskar per fack (totalt 8 TB) och 1 TB 5400 RPM 2,5"-hårddiskar (totalt 2 TB)
Inlänkningshastighet 15,000 cycles
Ström Power Source AC-adapter medföljer
Inspänning 110V-240V AC
Utspänning 12/5V DC
Utström 3A
Strömförbrukning 36
Särskilda anmärkningar/krav Obs. Vid duplicering måste målenheten ha lika stor eller större kapacitet än ursprungsenheten.

Om källenheten har en EISA-partition (Extended Industry Standard Architecture) måste den tas bort före kopiering.

eSATA-drift med två hårddiskar installerade kräver en eSATA-värdkontroller med stöd för port-multiplicering.

Utseende Färg Svart
Kabinettyp Av plast
Produktlängd 14,7 cm [5,8 in]
Produktbredd 13,2 cm [5,2 in]
Produkthöjd 70 mm [2,8 in]
Produktvikt 547 g [19,3 oz]
Vad det är i lådan 1 - Ingår i paketet SATA HDD-dockningsstation för hårddiskduplikator
eSATA-kabel
USB 2.0-kabel
Universell strömadapter
Instruktionsbok
3 - Ingår i paketet Strömkabel (NA/BG/EU)

Tillbehör

SAT2IDEADP

SATA till 2,5" eller 3,5" IDE-hårddisk-adapter för HDD-dockningsstationer

Använd 2,5 tums eller 3,5 tums IDE-hårddiskar i en SATA HDD-dockningsstation

Ditt pris
€31,99 EUR excl. VAT
€39,99 EUR incl. VAT
HDDSLEV25

2.5in Silicone Laptop Hard Drive Protector Sleeve with Connector Cap

Provide protection against shocks/impacts to a 2.5in hard drive

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
HDDSLEV35

3,5" skyddshylsa i silikon med kontaktlock för hårddiskar

Skydda en 3,5" hårddisk mot elstötar/sammanstötningar

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25YW

2.5in Anti-Static Hard Drive Protector Case - Yellow (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25WH

2.5in Anti-Static Hard Drive Protector Case - White (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25OR

2.5in Anti-Static Hard Drive Protector Case - Orange (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25GN

2.5in Anti-Static Hard Drive Protector Case - Green (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25BL

2.5in Anti-Static Hard Drive Protector Case - Blue (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
HDDCASE25BK

2,5" antistatiskt skyddsfodral för hårddiskar - Svart (3-pack)

Passar de flesta 2,5 tums hårddiskar och gör hanteringen säker samt skyddar mot statisk elektricitet

Ditt pris
€19,99 EUR excl. VAT
€24,99 EUR incl. VAT
ESATAPLT1LP

1ft Low Profile SATA to eSATA Plate Adapter

Add an eSATA port to your PC, extended from internal Serial ATA connection port

Ditt pris
€6,99 EUR excl. VAT
€8,74 EUR incl. VAT
ESATAPLATE1

SATA till eSATA PCI-täckplåtsanslutning med 1 port

Gör om en standard SATA-moderkortsanslutning till en extern eSATA-port

Ditt pris
€6,99 EUR excl. VAT
€8,74 EUR incl. VAT
ESATA6

1,8 m skärmad extern eSATA-kabel M/M

Anslut dina externa SATA-lagringsenheter till din bärbara eller stationära dator.

Ditt pris
€12,99 EUR excl. VAT
€16,24 EUR incl. VAT
ESATA3

3 ft Shielded External eSATA Cable M/M

Connect your external SATA storage devices to your Laptop or desktop.

Ditt pris
€9,99 EUR excl. VAT
€12,49 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

SATA hard drive controllers require a feature called port multiplier to read more than one hard drive per SATA or eSATA port. The port multiplier feature is not standard on many SATA hard drive controllers.

If your computer is only recognizing one of your hard drives, you need to plug the eSATA cable into a SATA controller that includes the port multiplier feature. If none of your current hard drive controllers include this feature, you can add a hard drive controller that does support port multiplier in any available expansion slot (for example, PCI, PCI-Express, PCMCIA, CardBus, or ExpressCard). StarTech.com has hard drive controllers available that support the port multiplier feature. To view the hard drive controllers, click here: http://startech.com/Cards-Adapters/HDD-Controllers/SATA-Cards/?filter_PORTMULTIPLIER=Yes.

If you have a hard drive controller card that does support the port multiplier feature but it is only reading one hard drive at a time, update the drivers of the hard drive controller. To find the most current StarTech.com drivers, click here: http://www.startech.com/Support.

When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables
  • Hard drives
  • Hard drive dock or duplicator

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive dock or duplicator in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive dock or duplicator in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:

Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  2. Do one of the following:
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive. 

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

This docking station allows the hard drive to enforce its own power state, as opposed to enforcing a power state that keeps the hard drive active at all times. Since most newer hard drives have low-power energy conservation modes, this will cause the hard drive to enter an idle state if it is not used for a certain amount of time. 

 

You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.

The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.

Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.

Extend a partition on a computer running Windows

Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.

After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:

  1. Press the Windows key + R.
  2. Type compmgmt.msc and click Ok.
  3. In Computer Management, on the left side of the screen, click Disk Management.
  4. Find the target drive. It will most likely be at the bottom of the list, have a partition that is the same size as the source drive, and have an unallocated area on the drive.
  5. On the target drive, right-click the last partition on the right side of the screen and click Extend Volume.
  6. In the Extend Volume wizard, click Next. By default, the remaining drive area is the amount of space used.
  7. Click Next > Finish.

The primary partition on the drive now uses the entire drive area.

StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode .  A duplication that fails or halts will not cause a problem with the source drive.

You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.

Hur man

To confirm that Windows detects your USB device, complete the following:

  1. Press the Windows key+R, type devmgmt.msc, and press Enter.
  2. In Device Manager, under the appropriate heading, confirm that your expansion card is listed and that there isn't an exclamation mark next to it.  For example, a USB controller card would be under Universal Serial Bus controllers.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

To confirm that the Mac OS detects your USB device, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your USB device is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

You may need to refresh the System Information page after you plug in your device.  To do so, press Command R with the System Information page open.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Before You Buy

StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.

If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.

Solid-state drives (SSDs) use SATA connectors to access power and transfer data. Any duplicator that can copy to or from SATA hard drives will work with a StarTech.com duplicator.

Note: If you use a dock to duplicate SSDs, keep in mind that the StarTech.com disk duplicators execute a sector by sector read and write. SSDs are rated by a number of reads and writes. Repeated duplication and sector by sector reads and writes of SSDs can reduce the life cycle of the drive.

Software-level encryption on the drive poses no issue to StarTech.com duplicators, as the duplicators copy encrypted data sector by sector over to the new drive.

Hardware-level encryption or BIOS level hard drive locks cause the duplication to halt and fail, as the drive is unable to read or write the sectors that are encrypted.

Duplication of Hidden Protected Area (HPA) Partitions or Extended Industry Standard Architecture (EISA) cause the duplicator to halt and fail, as the drive cannot read and write the protected partitions on the drive.

Note: Our UNIDUPDOCKSATDOCK22RE and SATDOCK4U3RE do include the ability to copy HPA partitions, but the duplication is still dependent on how the HPA partition is written to the hard drive, whether or not it is encrypted and how it is encrypted.

StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.

SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.

To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the device supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the device was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the device. For example, IDE, SATA, or M.2.
  • Make sure that the device supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the device. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the docking station.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Vänta...
Tillbaka till toppen