Produktsökning

USB 3.0 eSATA till fristående dockningsstation med 4 fack för 1:3 SATA hårddisk-duplikator

Duplicera en SATA-hårddisk till tre hårddiskar samtidigt

Produkt ID: SATDOCK4U3RE

  • Sektion-för-sektion-hårddiskduplicering, inklusive HPA (skyddade minnesplatser)
  • Integrerad LCD-skärm för dupliceringsförlopp och valmeny
  • SuperSpeed USB 3.0-kompatibelt värdgränssnitt med stöd för dataöverföringshastigheter på upp till 5 Gbps
Ditt pris
€717,99 EUR excl. VAT
€897,49 EUR incl. VAT

SATDOCK4U3RE fristående USB 3.0- och eSATA-1-till-3-hårddiskduplikatordocka gör att du kan duplicera/klona en enda SATA-hårddisk till upp till 3 SATA-hårddiskar samtidigt. Det går även att använda hårddiskduplikatorn som en vanlig hårddiskdockningsstation med fyra fack genom att ansluta den till ett värddatorsystem. Enheter med hög kapacitet (testad med upp till 4 TB 3,5"- och 1 TB 2,5"-enheter per fack) kan användas för att förbättra datorns lagrings/kopieringsmöjligheter.

Eftersom det går att utföra 1:3-sektionsduplicering, inklusive HPA, från en enda SATA-hårddisk till tre andra samtidigt (med en hastighet på upp till 72 Mbps) sparar duplikatorn/dockningsstationen både tid och besvär. Som extern HDD-dockningsstation går den att ansluta till datorn via USB 3.0 eller eSATA, vilket ger dataöverföringshastigheter på upp till 5 Gbps respektive 3 Gbps, från hårddiskarna till ditt datorsystem.

Har snabba och säkra raderingsfunktioner och stöd för IDE-hårddiskar via den medföljande SAT2IDEADP (SAT2IDEADP). Har snabba och säkra raderingsfunktioner och stöd för IDE-hårddiskar via den medföljande SAT2IDEADP (SAT2IDEADP). Denna hårddiskraderare säkerställer att data rensas (säkert radering), vilket krävs av myndigheter och organisationer med strikta riktlinjer för borttagning av data. Wipe är en mycket säker metod för att radera data från din lagringsenhet och den uppfyller NIST 800-88 Rev. 1 media sanitetsstandard som fastställts av National Institute of Standards and Technology.

Användning

  • Skapa flera exakta kopior av en källhårddisk till en ny hårddisk för stora antal identiska datorsystem
  • Brottsbekämpande organ och kriminaltekniker som behöver en eller fler exakta kopior av den ursprungliga hårddisken för testning och undersökning
  • SMB:er, OEM:er, systemintegratörer, IT- och servicetekniker som behöver snabb åtkomst till rent externt hårddiskinnehåll eller möjlighet att klona data för data-/diskåterställning.

Fördelarna med StarTech.com

  • Skapa 3 exakta kopior av en SATA-källhårddisk samtidigt, utan att behöva ansluta till en dator
  • Tillgång till upp till 4 SATA-hårddiskar samtidigt via en enda USB 3.0- eller eSATA-anslutning
  • Dubbla, fläktar med justerbar hastighet gör att du kan anpassa nedkylningsgraden till alla sorters miljöer eller hårddiskmodeller

Partnernummer

  • Ingram Micro Sweden V931530
  • UPC 065030843881

Kompatibilitet

Specifikationer

Warranty Information Warranty 2 Years
Förpackning Package Length 34,3 cm [13,5 in]
Package Width 17,0 cm [6,7 in]
Package Height 21,5 cm [8,5 in]
Fraktvikt (förpackning) 2,7 kg [6,0 lb]
Hårdvara Antal enheter 4
Enhetsstorlek 2.5in & 3.5in
Enhetstyp SATA
2 - Flaktar 60 mm
Chipset-ID JMicron - JMB394
JMicron - JMS539
Indikatorer 4 - LED-indikatorer Enhet ström/aktivitet
Kontakt(er) 4 - Enhetskontakter SATA data- & ström-kombo (7+15-stifts)
1 - Värdkontakter USB Type-B (9-stifts) USB 3.0
eSATA (7-stifts, data)
Miljö Drifttemperatur 5°C to 80°C (41°F to 176°F)
Förvaringstemperatur -40°C to 70°C (-40°F to 158°F)
Luftfuktighet 8~90 % RH
Mjukvara OS-kompatibilitet OS independent; No software or drivers required
Prestanda Maximal dataöverföringshastighet 3 Gbps
Typ och hastighet USB 3.0 - 5 Gbit/s
SATA II (3 Gbps)
Port Multiplier Ja
Duplication Modes Sector by Sector (Whole Drive)
Raderingslägen Quick Erase
Secure Erase (NIST SP 800-88 Rev 1 - Purge)
Maximal enhetskapacitet För närvarande testad med upp till 4 TB 5400 RPM 3.5" hårddiskar per fack (totalt 16 TB) och 1 TB 5400 RPM 2,5"-hårddiskar (totalt 4 TB)
Duplication Speed 4.2GBpm
Inlänkningshastighet 15,000 cycles per bay
Ström Power Source AC-adapter medföljer
Inspänning 100 - 240 AC
Inström 2.0 A
Utspänning 12V DC
Utström 6.5 A
Strömförbrukning 78
Utseende Färg Svart
Kabinettyp Av plast
Produktlängd 28,4 cm [11,2 in]
Produktbredd 17,2 cm [6,8 in]
Produkthöjd 96,0 mm [3,8 in]
Produktvikt 1,1 kg [2,4 lb]
Vad det är i lådan 1 - Ingår i paketet SATA-dockningsstation för hårddiskduplikator
SATA till IDE-adapter
USB 3.0-kabel
eSATA-kabel
SP4 till LP4-strömkabel
40 stifts IDE-kabel
Förpackning med monteringsskruvar
44 stifts till 40 stifts IDE-kabel
universell strömadapter (NA/JP, UK, EU, ANZ)
Instruktionsbok

Tillbehör

SAT2IDEADP

SATA till 2,5" eller 3,5" IDE-hårddisk-adapter för HDD-dockningsstationer

Använd 2,5 tums eller 3,5 tums IDE-hårddiskar i en SATA HDD-dockningsstation

Ditt pris
€31,99 EUR excl. VAT
€39,99 EUR incl. VAT
HDDSLEV25

2.5in Silicone Laptop Hard Drive Protector Sleeve with Connector Cap

Provide protection against shocks/impacts to a 2.5in hard drive

Ditt pris
€4,99 EUR excl. VAT
€6,24 EUR incl. VAT
HDDSLEV35

3,5" skyddshylsa i silikon med kontaktlock för hårddiskar

Skydda en 3,5" hårddisk mot elstötar/sammanstötningar

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
SVA12DN4NEUA

DC-strömadapter - 12 V, 6,5 A

Byt ut din borttappade eller trasiga strömadapter

Ditt pris
€53,99 EUR excl. VAT
€67,49 EUR incl. VAT
HDDCASE25BK

2,5" antistatiskt skyddsfodral för hårddiskar - Svart (3-pack)

Passar de flesta 2,5 tums hårddiskar och gör hanteringen säker samt skyddar mot statisk elektricitet

Ditt pris
€19,99 EUR excl. VAT
€24,99 EUR incl. VAT
Utgått
HDDCASE25BL

2.5in Anti-Static Hard Drive Protector Case - Blue (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25GN

2.5in Anti-Static Hard Drive Protector Case - Green (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25OR

2.5in Anti-Static Hard Drive Protector Case - Orange (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25WH

2.5in Anti-Static Hard Drive Protector Case - White (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
HDDCASE25YW

2.5in Anti-Static Hard Drive Protector Case - Yellow (3pk)

Provides safe handling and anti-static protection for most 2.5in hard drives

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
USB3SAB3BK

3 ft Black SuperSpeed USB 3.0 Cable A to B - M/M

Connect to your external solutions and transfer data at 10x the speed of USB 2.0

Ditt pris
€6,99 EUR excl. VAT
€8,74 EUR incl. VAT
ESATA6

1,8 m skärmad extern eSATA-kabel M/M

Anslut dina externa SATA-lagringsenheter till din bärbara eller stationära dator.

Ditt pris
€12,99 EUR excl. VAT
€16,24 EUR incl. VAT
ESATA3

3 ft Shielded External eSATA Cable M/M

Connect your external SATA storage devices to your Laptop or desktop.

Ditt pris
€9,99 EUR excl. VAT
€12,49 EUR incl. VAT
Utgått
PEXESATA1

1 Port PCI Express eSATA II Controller Card

Add an eSATA port to a desktop computer through a PCI Express slot

Ditt pris
€7,99 EUR excl. VAT
€9,99 EUR incl. VAT
Utgått
ECUSB3S2

2 Port ExpressCard SuperSpeed USB 3.0 Card Adapter with UASP Support

Add two USB 3.0 ports to your laptop through an ExpressCard slot

Ditt pris
€21,99 EUR excl. VAT
€27,49 EUR incl. VAT
Utgått
PEXUSB3S2

PCI Express SuperSpeed USB 3.0-kortadapter med 2 portar och UASP-stöd

Lägg till två USB 3.0-portar till din stationära dator genom en PCI Express-utbyggnadskortplats

Ditt pris
€34,99 EUR excl. VAT
€43,74 EUR incl. VAT
Utgått
ECESATA1

1 Port Flush Mount ExpressCard 34mm eSATA II Controller Adapter Card

Add a slim flush mounting eSATA port to a laptop through ExpressCard

Ditt pris
€27,99 EUR excl. VAT
€34,99 EUR incl. VAT
Utgått
ECUSB3S1

1 Port Flush Mount ExpressCard SuperSpeed USB 3.0 Card Adapter with UASP Support

Flush mount a USB 3.0 ExpressCard adapter into a laptop ExpressCard slot

Ditt pris
€22,46 EUR excl. VAT
€28,08 EUR incl. VAT
ECESATA254F

2 Port Flush Mount ExpressCard 54mm eSATA II Controller Adapter Card

Add 2 flush mounted eSATA ports to a laptop through an ExpressCard/54 slot

Ditt pris
€32,99 EUR excl. VAT
€41,24 EUR incl. VAT

Drivers/Downloads

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Manual(er):

Datasheet

Produktsupport

Prata med en rådgivare.

Vi är alltid redo att hjälpa dig med alla dina frågor.

Direktchatt (opens in new window)

Vanliga frågor

Problemsökning

When you troubleshoot issues with a hard drive dock or duplicator, there are some quick tests that you can complete to rule out potential problems. You can test to make sure that the following components are working correctly and are not the source of the issue:

  • IDE, SATA, and eSATA cables
  • Hard drives
  • Hard drive dock or duplicator

To test your setup components, try the following:

  • Use the cables, hard drives, and hard drive dock or duplicator in another setup to see if the problem is with the components or the setup.
  • Use a different cable, hard drive, and hard drive dock or duplicator in your setup to see if the problem persists. Ideally, you should test a component that you know works in another setup.

When you test the hard drive and hard drive dock or duplicator, it is recommended that you do the following:

Note: For a hard drive duplicator you may need to switch the device to PC mode (if available).

  1. To check Disk Management, press the Windows key + R, type diskmgmt.msc, and press Enter. Check to see if your hard drive is listed.
  2. Do one of the following:
  • If the hard drive is listed with unallocated space, the hard drive needs to be reformatted. Right-click unallocated and click New Simple Volume. Follow the on-screen instructions to complete the reformatting.​

Note: Formatting a hard drive erases all of the data on it. Make sure that you back up all of your data before you reformat the hard drive. 

  • If the hard drive is listed as healthy but does not have a drive letter, for example, C:, right-click healthy and click Change Drive Letter and Paths. Click Add, assign a drive letter, and click OK.

Note: A formatted hard drive will not show up in Computer or My Computer until it has a drive letter assigned to it.

This docking station allows the hard drive to enforce its own power state, as opposed to enforcing a power state that keeps the hard drive active at all times. Since most newer hard drives have low-power energy conservation modes, this will cause the hard drive to enter an idle state if it is not used for a certain amount of time. 

 

You do not need to format your target hard drive before you begin to duplicate it, because the target hard drive is automatically overwritten during the duplication process.

The hard drive duplicator copies the exact partition from the source drive to the target drive. Since it is required that you use a target drive that is equal or larger in size than the source drive a portion of the target drive appears as free space. You can append free space to the live partition on the target drive so that the full size of the drive can be utilized.

Note: A partition cannot be extended on an operating system drive that is in use. You must extend the partition when it not being used by the operating system, and ideally when it is still connected to the duplicator.

Extend a partition on a computer running Windows

Note: Do not extend a System Reserved partition. Only extend the primary partition, which is typically the largest in size and formatted with NTFS or FAT32.

After you have successfully duplicated a drive and the target drive is still connected to your computer system (for example, through the duplicator), complete the following:

  1. Press the Windows key + R.
  2. Type compmgmt.msc and click Ok.
  3. In Computer Management, on the left side of the screen, click Disk Management.
  4. Find the target drive. It will most likely be at the bottom of the list, have a partition that is the same size as the source drive, and have an unallocated area on the drive.
  5. On the target drive, right-click the last partition on the right side of the screen and click Extend Volume.
  6. In the Extend Volume wizard, click Next. By default, the remaining drive area is the amount of space used.
  7. Click Next > Finish.

The primary partition on the drive now uses the entire drive area.

You can use the SATDOCK4U3RE to skip bad sectors on a hard drive. For more information, visit the following FAQ: http://www.startech.com/ca/faq/hard_drive_duplicators_failing_drives.

To use the SATDOCK4U3RE to skip bad sectors, you need to enable Read Error Skip. By default, Read Error Skip is disabled.

To enable Read Error Skip, complete the following:

  1. Turn on the SATDOCK4U3RE.

  2. Press ENT four times to enable Duplicator mode.

  3. Press ESC to open the menu.

  4. Press UP to open the Advanced Setup menu.

  5.  Press ENT twice to open the ReadErr Skip menu.

  6. Select Enable and then press ENT twice.

  7. Wait a few seconds for the unit to exit the menu.

StarTech.com hard drive duplicators only read from the source drive and only write to the target drives while in standalone duplication mode .  A duplication that fails or halts will not cause a problem with the source drive.

You can use this device to duplicate an internal hard drive with the stand alone duplicator function if you remove the hard drive from the computer and connect it directly to this device.

Hur man

To confirm that the Mac OS detects your USB device, complete the following:

  1. Click the Apple icon.
  2. Click About This Mac.
  3. Click More Info or System Report.
  4. Under the appropriate heading, confirm that your USB device is listed and that there isn't an error. For example, a network card would be under Ethernet Cards.

You may need to refresh the System Information page after you plug in your device.  To do so, press Command R with the System Information page open.

Your USB device is listed according to the name of the chipset. To determine the name of the chipset of your USB device, navigate to www.StarTech.com and look on the Technical Specifications tab for your product.

Before You Buy

StarTech.com hard drive and flash drive duplicators perform a sector by sector copy, which means that the target drive must be the exact same size (down to the sector) or larger than the hard drive or flash drive that is being copied. During a sector by sector copy, each individual sector is copied over to the target drive, regardless of whether or not any data is present. A 500 GB hard drive with 50 GB of data on it will take the same amount of time to copy as a 500 GB hard drive with 450 GB of data on it.

If you have two hard drives or flash drives that are listed as the same size but are different makes or models, you need to check how large both drives are down to the sector to ensure that the target drive is is the exact same size or larger.

Solid-state drives (SSDs) use SATA connectors to access power and transfer data. Any duplicator that can copy to or from SATA hard drives will work with a StarTech.com duplicator.

Note: If you use a dock to duplicate SSDs, keep in mind that the StarTech.com disk duplicators execute a sector by sector read and write. SSDs are rated by a number of reads and writes. Repeated duplication and sector by sector reads and writes of SSDs can reduce the life cycle of the drive.

Software-level encryption on the drive poses no issue to StarTech.com duplicators, as the duplicators copy encrypted data sector by sector over to the new drive.

Hardware-level encryption or BIOS level hard drive locks cause the duplication to halt and fail, as the drive is unable to read or write the sectors that are encrypted.

Duplication of Hidden Protected Area (HPA) Partitions or Extended Industry Standard Architecture (EISA) cause the duplicator to halt and fail, as the drive cannot read and write the protected partitions on the drive.

Note: Our UNIDUPDOCKSATDOCK22RE and SATDOCK4U3RE do include the ability to copy HPA partitions, but the duplication is still dependent on how the HPA partition is written to the hard drive, whether or not it is encrypted and how it is encrypted.

StarTech.com duplicators were not designed to recover failing or damaged drives. If the duplicator encounters a corrupt or unreadable sector, the duplication halts and fails.

SATDOCK4U3RE, SATDUP13 ,and UNIDUPDOCK all include a function that allows the duplicators to skip over corrupt or unreadable sectors. However, if the duplicators encounter too many errors, they still halt and fail. If this happens, you will need third-party recovery software or custom-built recovery hardware to copy from a failing or damaged drive.

Quick and secure erase functions

Quick erase and secure erase are functions the duplicators call on the hard drives themselves. How they work depends on the manufacturer of the hard drive.

Department of Defense erase function

A Department of Defense (DoD) erase is a function performed by the duplicator where it does three passes. The first pass writes all 0s. The second pass writes all 1s. The third pass writes 0s and 1s randomly.

Note: Not all duplicators will feature all of these erase modes. It is important to review the product manual to confirm the available erase modes.

To determine if your hard drive will work in this device, on the product page, click the Technical Specifications tab, and do the following:

  • Make sure that the device supports the storage size of your hard drive. If the storage size of your hard drive is larger than what the device was tested with, the hard drive will likely still work with the enclosure.
  • Confirm that your hard drive uses the same interface type as the device. For example, IDE, SATA, or M.2.
  • Make sure that the device supports the physical size of your hard drive, such as 2.5 inches or 3.5 inches.
  • Verify that the power consumption of your hard drive doesn’t exceed the power output of the device. If you’re using multiple hard drives, make sure that the combined power consumption of all of the hard drives doesn’t exceed the power output of the docking station.

Hard Drives

Windows 10 

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, ex-FAT, NTFS, and so on).

Initialize a drive

Note: You typically only need to initialize a drive if the drive is new. If you cannot find an uninitialized drive in Disk Management, skip the following steps and try to partition your device.

  1. Press the Windows key + R, type compmgmt.msc, and click Run to open Computer Management.

  2. Navigate to Disk Management.

  3. When prompted to, initialize your disk(s). If you are running Windows® 7 or later and are using a drive larger than 2TB, initialize the disk(s) with GPT. If you are running an earlier version of Windows, initialize the disk(s) with MBR. For more information, visit the following FAQ: https://www.startech.com/support/faqs/technical-support?topic=hard-drives#mbr-vs-gpt.

  4. Click OK.

Create a partition in a drive

Note: The following steps create an NTFS partition that uses the entire drive space. To use a different file system, select a different option in step 6.

  1. Right-click Unallocated or RAW volume, and select New Simple Volume.

  2. In the New Partition Wizard, click Next.

  3. Select Primary partition.

  4. Leave the partition size set to default, and click Next.

  5. Assign a drive letter or leave it set to the default, and click Next.

  6. Enter the following settings to format the partition:

  • In the File System field, enter NTFS.
  • Set the Allocation unit size to Default.
  • In the Volume label field, enter <your name/reference>.
  • Select the Perform a quick format check box.
  • Clear the Enable file and folder compression check box.
  1. Click Next > Finish.

The new drive should appear in Windows Explorer.

Mac OS

Before you can access a new or formatted drive in your operating system, you need to initialize it first and then create a partition on the drive. A partition defines an area of the drive to use for storing data. The partition uses a file system (for example, HFS+, ex-FAT, NTFS, and so on).

Initialize a drive

Mac OSX detects a drive that needs to be initialized and automatically prompts you to initialize the drive. If you are prompted to initialize the drive, click Initialize. If you are not prompted to initialize the drive and you cannot find the drive in Finder, you will need to create a partition on the drive.

Create a partition on a drive

Note: The following steps create an HFS+ (Mac OS Extended (Journaled)) partition that uses the entire drive space.

To create a partition on a new drive, complete the following:

  1. Open Finder.

  2. Navigate to Applications and click Utilities.

  3. Open Disk Utility.

  4. Select the new drive and click the Partition tab.

  5. Click Options and verify that it is set to GUID Partition Table.

  6. Enter a name for the partition.

  7. Click Partition.

The drive should now be accessible in Finder.

Compliance and safety

Compliance letters

Safety Measures

  • If product has an exposed circuit board, do not touch the product under power.
  • If Class 1 Laser Product. Laser radiation is present when the system is open.
  • Wiring terminations should not be made with the product and/or electric lines under power.
  • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.
  • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
* Produkters utseende och specifikationer kan komma att ändras utan förvarning.
Vänta...
Tillbaka till toppen